[3/3] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[CK Hu]

Hi, Xinlei:

On Fri, 2022-02-11 at 22:30 +0800, xinlei.lee at mediatek.com wrote:
> From: Jitao Shi <jitao.shi at mediatek.com>
> 
> To comply with the panel sequence, hold the mipi signal to LP00
> before the dcs cmds transmission, 
> and pull the mipi signal high from LP00 to LP11 until the start of
> the dcs cmds transmission.
> If dsi is not in cmd mode, then dsi will pull the mipi signal high in
> the mtk_output_dsi_enable function.
> 
> Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee at mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 32 +++++++++++++++++++++++++---
> ----
>  1 file changed, 25 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index e47c338..17a5270 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -203,6 +203,7 @@ struct mtk_dsi {
>  	struct mtk_phy_timing phy_timing;
>  	int refcount;
>  	bool enabled;
> +	bool lanes_ready;
>  	u32 irq_data;
>  	wait_queue_head_t irq_wait_queue;
>  	const struct mtk_dsi_driver_data *driver_data;
> @@ -654,13 +655,6 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
>  	mtk_dsi_config_vdo_timing(dsi);
>  	mtk_dsi_set_interrupt_enable(dsi);
>  
> -	mtk_dsi_rxtx_control(dsi);
> -	usleep_range(30, 100);
> -	mtk_dsi_reset_dphy(dsi);
> -	mtk_dsi_clk_ulp_mode_leave(dsi);
> -	mtk_dsi_lane0_ulp_mode_leave(dsi);
> -	mtk_dsi_clk_hs_mode(dsi, 0);
> -
>  	return 0;
>  err_disable_engine_clk:
>  	clk_disable_unprepare(dsi->engine_clk);
> @@ -682,6 +676,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
>  	mtk_dsi_reset_engine(dsi);
>  	mtk_dsi_lane0_ulp_mode_enter(dsi);
>  	mtk_dsi_clk_ulp_mode_enter(dsi);
> +	/* set the lane number as 0 */
> +	writel(0, dsi->regs + DSI_TXRX_CTRL);

If this is not related to 'sequence', separate this to another patch.

Regards,
CK

>  
>  	mtk_dsi_disable(dsi);
>  
> @@ -689,6 +685,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
>  	clk_disable_unprepare(dsi->digital_clk);
>  
>  	phy_power_off(dsi->phy);
> +
> +	dsi->lanes_ready = false;
>  }
>  
>  static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
> @@ -696,6 +694,16 @@ static void mtk_output_dsi_enable(struct mtk_dsi
> *dsi)
>  	if (dsi->enabled)
>  		return;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +	}
> +
>  	mtk_dsi_set_mode(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 1);
>  
> @@ -907,6 +915,16 @@ static ssize_t mtk_dsi_host_transfer(struct
> mipi_dsi_host *host,
>  	if (MTK_DSI_HOST_IS_READ(msg->type))
>  		irq_flag |= LPRX_RD_RDY_INT_FLAG;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +		msleep(20);
> +	}
>  	if (mtk_dsi_host_send_cmd(dsi, msg, irq_flag) < 0)
>  		return -ETIME;
>