[PATCH v2 04/15] dt-bindings: ufs: drop unused/old ufs-qcom PHY bindings

[Bjorn Andersson]

On Tue 22 Feb 06:58 PST 2022, Krzysztof Kozlowski wrote:

> The Qualcomm UFS PHY bindings are documented in
> bindings/phy/qcom,qmp-phy.yaml and the compatibles from separate file
> bindings/ufs/ufs-qcom.txt are not used at all.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski at canonical.com>

Reviewed-by: Bjorn Andersson <bjorn.andersson at linaro.org>

> ---
>  .../devicetree/bindings/ufs/ufs-qcom.txt      | 63 -------------------
>  1 file changed, 63 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/ufs/ufs-qcom.txt
> 
> diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt
> deleted file mode 100644
> index fd59f93e9556..000000000000
> --- a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt
> +++ /dev/null
> @@ -1,63 +0,0 @@
> -* Qualcomm Technologies Inc Universal Flash Storage (UFS) PHY
> -
> -UFSPHY nodes are defined to describe on-chip UFS PHY hardware macro.
> -Each UFS PHY node should have its own node.
> -
> -To bind UFS PHY with UFS host controller, the controller node should
> -contain a phandle reference to UFS PHY node.
> -
> -Required properties:
> -- compatible        : compatible list, contains one of the following -
> -			"qcom,ufs-phy-qmp-20nm" for 20nm ufs phy,
> -			"qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy,
> -			"qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy
> -			 present on MSM8996 chipset.
> -- reg               : should contain PHY register address space (mandatory),
> -- reg-names         : indicates various resources passed to driver (via reg proptery) by name.
> -                      Required "reg-names" is "phy_mem".
> -- #phy-cells        : This property shall be set to 0
> -- vdda-phy-supply   : phandle to main PHY supply for analog domain
> -- vdda-pll-supply   : phandle to PHY PLL and Power-Gen block power supply
> -- clocks	    : List of phandle and clock specifier pairs
> -- clock-names       : List of clock input name strings sorted in the same
> -		      order as the clocks property. "ref_clk_src", "ref_clk",
> -		      "tx_iface_clk" & "rx_iface_clk" are mandatory but
> -		      "ref_clk_parent" is optional
> -
> -Optional properties:
> -- vdda-phy-max-microamp : specifies max. load that can be drawn from phy supply
> -- vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply
> -- vddp-ref-clk-supply   : phandle to UFS device ref_clk pad power supply
> -- vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply
> -- resets : specifies the PHY reset in the UFS controller
> -
> -Example:
> -
> -	ufsphy1: ufsphy at fc597000 {
> -		compatible = "qcom,ufs-phy-qmp-20nm";
> -		reg = <0xfc597000 0x800>;
> -		reg-names = "phy_mem";
> -		#phy-cells = <0>;
> -		vdda-phy-supply = <&pma8084_l4>;
> -		vdda-pll-supply = <&pma8084_l12>;
> -		vdda-phy-max-microamp = <50000>;
> -		vdda-pll-max-microamp = <1000>;
> -		clock-names = "ref_clk_src",
> -			"ref_clk_parent",
> -			"ref_clk",
> -			"tx_iface_clk",
> -			"rx_iface_clk";
> -		clocks = <&clock_rpm clk_ln_bb_clk>,
> -			<&clock_gcc clk_pcie_1_phy_ldo >,
> -			<&clock_gcc clk_ufs_phy_ldo>,
> -			<&clock_gcc clk_gcc_ufs_tx_cfg_clk>,
> -			<&clock_gcc clk_gcc_ufs_rx_cfg_clk>;
> -		resets = <&ufshc 0>;
> -	};
> -
> -	ufshc: ufshc at fc598000 {
> -		#reset-cells = <1>;
> -		...
> -		phys = <&ufsphy1>;
> -		phy-names = "ufsphy";
> -	};
> -- 
> 2.32.0
>