[PATCH v2 11/11] ARM: dts: armada-385.dtsi: Add definitions for PCIe legacy INTx interrupts
Pali Rohár
pali at kernel.org
Sat Feb 19 05:36:15 PST 2022
Perfect, thanks!
On Friday 18 February 2022 21:53:43 Luís Mendes wrote:
> Successfully tested on my custom A388 system with two PCI express slots.
>
> If you wish you can add a:
> Tested-by: Luis Mendes <luis.p.mendes at gmail.com>
>
> On Tue, Feb 15, 2022 at 10:52 AM Pali Rohár <pali at kernel.org> wrote:
> >
> > Hello! armada-388.dtsi file has #include "armada-385.dtsi" line and
> > therefore is already covered by this my patch.
> >
> > Gregory's question was about A380.
> >
> > But if you want, you can test this patch series (which already covers
> > A388) on your A388 HW. It is still better to do tests on more HW.
> >
> > On Tuesday 15 February 2022 10:48:17 Luís Mendes wrote:
> > > Hello,
> > >
> > > Sorry for jumping in the conversation, but I read this thread and I
> > > have an Armada A388 HW so I can test it, if desired.
> > >
> > > Luís
> > >
> > >
> > > On Tue, Feb 15, 2022 at 10:47 AM Luís Mendes <luis.p.mendes at gmail.com> wrote:
> > > >
> > > > Hello,
> > > >
> > > > Sorry for jumping in the conversation, but I read this thread and I have an Armada A388 HW so I can test it, if desired.
> > > >
> > > > Luís
> > > >
> > > > On Mon, Feb 14, 2022 at 7:57 PM Gregory CLEMENT <gregory.clement at bootlin.com> wrote:
> > > >>
> > > >> Hello,
> > > >>
> > > >> > On Monday 14 February 2022 16:07:13 Gregory CLEMENT wrote:
> > > >> >> Hello Pali,
> > > >> >>
> > > >> >> > With this change legacy INTA, INTB, INTC and INTD interrupts are reported
> > > >> >> > separately and not mixed into one Linux virq source anymore.
> > > >> >> >
> > > >> >> > Signed-off-by: Pali Rohár <pali at kernel.org>
> > > >> >> > ---
> > > >> >> > arch/arm/boot/dts/armada-385.dtsi | 52 ++++++++++++++++++++++++++-----
> > > >> >>
> > > >> >> Is there any reason for not doing the same change in armada-380.dtsi ?
> > > >> >
> > > >> > I do not have A380 HW, so I did this change only for A385 which I have
> > > >> > tested.
> > > >>
> > > >> OK fair enough.
> > > >>
> > > >> So you can add my
> > > >> Acked-by: Gregory CLEMENT <gregory.clement at bootlin.com>
> > > >>
> > > >> Moreover to keep biscetability this patch should be merged after the
> > > >> support in the driver. So the easier is to let merge it through the PCI
> > > >> subsystem with the other patches from this series. I do not think there
> > > >> will be any other changes in this file so there won't be any merge
> > > >> conflicts.
> > > >>
> > > >> Thanks,
> > > >>
> > > >> Grégory
> > > >>
> > > >>
> > > >> >
> > > >> >> Grégory
> > > >> >>
> > > >> >> > 1 file changed, 44 insertions(+), 8 deletions(-)
> > > >> >> >
> > > >> >> > diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi
> > > >> >> > index f0022d10c715..83392b92dae2 100644
> > > >> >> > --- a/arch/arm/boot/dts/armada-385.dtsi
> > > >> >> > +++ b/arch/arm/boot/dts/armada-385.dtsi
> > > >> >> > @@ -69,16 +69,25 @@
> > > >> >> > reg = <0x0800 0 0 0 0>;
> > > >> >> > #address-cells = <3>;
> > > >> >> > #size-cells = <2>;
> > > >> >> > + interrupt-names = "intx";
> > > >> >> > + interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > #interrupt-cells = <1>;
> > > >> >> > ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> > > >> >> > 0x81000000 0 0 0x81000000 0x1 0 1 0>;
> > > >> >> > bus-range = <0x00 0xff>;
> > > >> >> > - interrupt-map-mask = <0 0 0 0>;
> > > >> >> > - interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > + interrupt-map-mask = <0 0 0 7>;
> > > >> >> > + interrupt-map = <0 0 0 1 &pcie1_intc 0>,
> > > >> >> > + <0 0 0 2 &pcie1_intc 1>,
> > > >> >> > + <0 0 0 3 &pcie1_intc 2>,
> > > >> >> > + <0 0 0 4 &pcie1_intc 3>;
> > > >> >> > marvell,pcie-port = <0>;
> > > >> >> > marvell,pcie-lane = <0>;
> > > >> >> > clocks = <&gateclk 8>;
> > > >> >> > status = "disabled";
> > > >> >> > + pcie1_intc: interrupt-controller {
> > > >> >> > + interrupt-controller;
> > > >> >> > + #interrupt-cells = <1>;
> > > >> >> > + };
> > > >> >> > };
> > > >> >> >
> > > >> >> > /* x1 port */
> > > >> >> > @@ -88,16 +97,25 @@
> > > >> >> > reg = <0x1000 0 0 0 0>;
> > > >> >> > #address-cells = <3>;
> > > >> >> > #size-cells = <2>;
> > > >> >> > + interrupt-names = "intx";
> > > >> >> > + interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > #interrupt-cells = <1>;
> > > >> >> > ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
> > > >> >> > 0x81000000 0 0 0x81000000 0x2 0 1 0>;
> > > >> >> > bus-range = <0x00 0xff>;
> > > >> >> > - interrupt-map-mask = <0 0 0 0>;
> > > >> >> > - interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > + interrupt-map-mask = <0 0 0 7>;
> > > >> >> > + interrupt-map = <0 0 0 1 &pcie2_intc 0>,
> > > >> >> > + <0 0 0 2 &pcie2_intc 1>,
> > > >> >> > + <0 0 0 3 &pcie2_intc 2>,
> > > >> >> > + <0 0 0 4 &pcie2_intc 3>;
> > > >> >> > marvell,pcie-port = <1>;
> > > >> >> > marvell,pcie-lane = <0>;
> > > >> >> > clocks = <&gateclk 5>;
> > > >> >> > status = "disabled";
> > > >> >> > + pcie2_intc: interrupt-controller {
> > > >> >> > + interrupt-controller;
> > > >> >> > + #interrupt-cells = <1>;
> > > >> >> > + };
> > > >> >> > };
> > > >> >> >
> > > >> >> > /* x1 port */
> > > >> >> > @@ -107,16 +125,25 @@
> > > >> >> > reg = <0x1800 0 0 0 0>;
> > > >> >> > #address-cells = <3>;
> > > >> >> > #size-cells = <2>;
> > > >> >> > + interrupt-names = "intx";
> > > >> >> > + interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > #interrupt-cells = <1>;
> > > >> >> > ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
> > > >> >> > 0x81000000 0 0 0x81000000 0x3 0 1 0>;
> > > >> >> > bus-range = <0x00 0xff>;
> > > >> >> > - interrupt-map-mask = <0 0 0 0>;
> > > >> >> > - interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > + interrupt-map-mask = <0 0 0 7>;
> > > >> >> > + interrupt-map = <0 0 0 1 &pcie3_intc 0>,
> > > >> >> > + <0 0 0 2 &pcie3_intc 1>,
> > > >> >> > + <0 0 0 3 &pcie3_intc 2>,
> > > >> >> > + <0 0 0 4 &pcie3_intc 3>;
> > > >> >> > marvell,pcie-port = <2>;
> > > >> >> > marvell,pcie-lane = <0>;
> > > >> >> > clocks = <&gateclk 6>;
> > > >> >> > status = "disabled";
> > > >> >> > + pcie3_intc: interrupt-controller {
> > > >> >> > + interrupt-controller;
> > > >> >> > + #interrupt-cells = <1>;
> > > >> >> > + };
> > > >> >> > };
> > > >> >> >
> > > >> >> > /*
> > > >> >> > @@ -129,16 +156,25 @@
> > > >> >> > reg = <0x2000 0 0 0 0>;
> > > >> >> > #address-cells = <3>;
> > > >> >> > #size-cells = <2>;
> > > >> >> > + interrupt-names = "intx";
> > > >> >> > + interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > #interrupt-cells = <1>;
> > > >> >> > ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
> > > >> >> > 0x81000000 0 0 0x81000000 0x4 0 1 0>;
> > > >> >> > bus-range = <0x00 0xff>;
> > > >> >> > - interrupt-map-mask = <0 0 0 0>;
> > > >> >> > - interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> > > >> >> > + interrupt-map-mask = <0 0 0 7>;
> > > >> >> > + interrupt-map = <0 0 0 1 &pcie4_intc 0>,
> > > >> >> > + <0 0 0 2 &pcie4_intc 1>,
> > > >> >> > + <0 0 0 3 &pcie4_intc 2>,
> > > >> >> > + <0 0 0 4 &pcie4_intc 3>;
> > > >> >> > marvell,pcie-port = <3>;
> > > >> >> > marvell,pcie-lane = <0>;
> > > >> >> > clocks = <&gateclk 7>;
> > > >> >> > status = "disabled";
> > > >> >> > + pcie4_intc: interrupt-controller {
> > > >> >> > + interrupt-controller;
> > > >> >> > + #interrupt-cells = <1>;
> > > >> >> > + };
> > > >> >> > };
> > > >> >> > };
> > > >> >> > };
> > > >> >> > --
> > > >> >> > 2.20.1
> > > >> >> >
> > > >> >>
> > > >> >> --
> > > >> >> Gregory Clement, Bootlin
> > > >> >> Embedded Linux and Kernel engineering
> > > >> >> http://bootlin.com
> > > >>
> > > >> --
> > > >> Gregory Clement, Bootlin
> > > >> Embedded Linux and Kernel engineering
> > > >> http://bootlin.com
More information about the linux-arm-kernel
mailing list