[PATCH] ARM: dts: mvebu: Add Ctera C-200 V2 board
Pawel Dembicki
paweldembicki at gmail.com
Wed Feb 16 03:43:09 PST 2022
Ctera C200 V2 is armada-370 based 2-Bay NAS.
Hardware:
- SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
- Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
- NAND Flash: 256MB (ESMT F59L2G81A-25T)
- Lan: 1x GBE (Marvell 88E1318-NNB2)
- Storage: 2x SATA HDD 3.5" Slot
- USB: 2x USB 3.0 port (Renesas uPD720202)
- Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
- LEDs: 13x GPIO controlled
- Buttons: 2x GPIO controlled
Signed-off-by: Pawel Dembicki <paweldembicki at gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/armada-370-c200-v2.dts | 388 +++++++++++++++++++++++
2 files changed, 389 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-370-c200-v2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31616f6ae173..bc7b3aac8135 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1416,6 +1416,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-zybo.dtb \
zynq-zybo-z7.dtb
dtb-$(CONFIG_MACH_ARMADA_370) += \
+ armada-370-c200-v2.dtb \
armada-370-db.dtb \
armada-370-dlink-dns327l.dtb \
armada-370-mirabox.dtb \
diff --git a/arch/arm/boot/dts/armada-370-c200-v2.dts b/arch/arm/boot/dts/armada-370-c200-v2.dts
new file mode 100644
index 000000000000..dd9738233b36
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-c200-v2.dts
@@ -0,0 +1,388 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Device Tree file for Ctera C200-V2
+ *
+ * Copyright (C) 2022 Pawel Dembicki <paweldembicki at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Ctera C200 V2";
+ compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>; /* 1024 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+ };
+
+ thermal-zones {
+ ethphy-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <2000>;
+
+ thermal-sensors = <ðphy0>;
+
+ trips {
+ ethphy_alert1: trip1 {
+ temperature = <65000>;
+ hysteresis = <4000>;
+ type = "passive";
+ };
+
+ ethphy_crit: trip2 {
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ beeper {
+ compatible = "pwm-beeper";
+ pinctrl-0 = <&pmx_beeper>;
+ pinctrl-names = "default";
+ pwms = <&gpio1 31 4000>;
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ };
+
+ usb1 {
+ label = "USB1 Button";
+ linux,code = <BTN_0>;
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2 {
+ label = "USB2 Button";
+ linux,code = <BTN_1>;
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+ pinctrl-names = "default";
+
+ led-0 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ function = LED_FUNCTION_USB;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ };
+
+ led-4 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-5 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ };
+
+ led-6 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ };
+
+ led-7 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-8 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ };
+
+ led-9 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+ };
+
+ led-10 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+ };
+
+ led-11 {
+ function = LED_FUNCTION_DISK;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+
+ led-12 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&coherencyfab {
+ broken-idle;
+};
+
+ð1 {
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-handle = <ðphy0>;
+ phy-connection-type = "rgmii-id";
+};
+
+&i2c0 {
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <100000>;
+ status = "okay";
+
+ hwmon at 2a {
+ compatible = "nuvoton,nct7802";
+ reg = <0x2a>;
+ };
+
+ rtc at 30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+};
+
+&mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ ethphy0: ethernet-phy at 0 { /* Marvell 88E1318 */
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ marvell,nand-keep-config;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0000000 0x200000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "certificate";
+ reg = <0x0200000 0x100000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "preset_cfg";
+ reg = <0x0300000 0x100000>;
+ read-only;
+ };
+
+ partition at 400000 {
+ label = "dev_params";
+ reg = <0x0400000 0x100000>;
+ read-only;
+ };
+ partition at 500000 {
+ label = "active_bank";
+ reg = <0x0500000 0x0100000>;
+ };
+
+ partition at 600000 {
+ label = "magic";
+ reg = <0x0600000 0x0100000>;
+ read-only;
+ };
+
+ partition at 700000 {
+ label = "bank1";
+ reg = <0x0700000 0x2800000>;
+ };
+
+ partition at 2f00000 {
+ label = "bank2";
+ reg = <0x2f00000 0x2800000>;
+ };
+
+ /* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+ partition at 5a00000 {
+ label = "reserved";
+ reg = <0x5a00000 0x2000000>;
+ };
+
+ partition at 7a00000 {
+ label = "rootfs";
+ reg = <0x7a00000 0x8600000>;
+ };
+ };
+ };
+};
+
+&pciec {
+ status = "okay";
+
+ pcie at 1,0 { /* Renesas uPD720202 USB 3.0 controller */
+ pinctrl-0 = <&pmx_pcie>;
+ pinctrl-names = "default";
+ status = "okay";
+ reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ pmx_poweroff: pmx-poweroff {
+ marvell,pins = "mpp7";
+ marvell,function = "gpo";
+ };
+
+ pmx_power_cpu: pmx-power-cpu {
+ marvell,pins = "mpp4";
+ marvell,function = "vdd";
+ };
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
+ marvell,function = "gpio";
+ };
+
+ pmx_leds1: pmx-leds1 {
+ marvell,pins = "mpp47";
+ marvell,function = "gpo";
+ };
+
+ pmx_leds2: pmx-leds2 {
+ marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
+ "mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
+ marvell,function = "gpio";
+ };
+
+ pmx_pcie: pmx-pcie {
+ marvell,pins = "mpp59";
+ marvell,function = "gpio";
+ };
+
+ pmx_beeper: pmx-beeper {
+ marvell,pins = "mpp63";
+ marvell,function = "gpio";
+ };
+};
+
+&pmsu {
+ pinctrl-0 = <&pmx_power_cpu>;
+ pinctrl-names = "default";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&sata {
+ nr-ports = <2>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdd0_temp: sata-port at 0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ hdd1_temp: sata-port at 1 {
+ reg = <1>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--
2.25.1
More information about the linux-arm-kernel
mailing list