[2/3] drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs

[xinlei.lee at mediatek.com]

From: Jitao Shi <jitao.shi at mediatek.com>

In order to match the changes of DSI RX devices (for example, anx7625), 
the poweron/poweroff of dsi is extracted from enable/disable and 
defined as new funcs (pre_enable/post_disable).

Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee at mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 45 ++++++++++++++++++++++----------------
 1 file changed, 26 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 6d7b66d..e47c338 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -679,16 +679,6 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	if (--dsi->refcount != 0)
 		return;
 
-	/*
-	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
-	 * mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(),
-	 * which needs irq for vblank, and mtk_dsi_stop() will disable irq.
-	 * mtk_dsi_start() needs to be called in mtk_output_dsi_enable(),
-	 * after dsi is fully set.
-	 */
-	mtk_dsi_stop(dsi);
-
-	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_lane0_ulp_mode_enter(dsi);
 	mtk_dsi_clk_ulp_mode_enter(dsi);
@@ -703,17 +693,9 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 {
-	int ret;
-
 	if (dsi->enabled)
 		return;
 
-	ret = mtk_dsi_poweron(dsi);
-	if (ret < 0) {
-		DRM_ERROR("failed to power on dsi\n");
-		return;
-	}
-
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -727,7 +709,16 @@ static void mtk_output_dsi_disable(struct mtk_dsi *dsi)
 	if (!dsi->enabled)
 		return;
 
-	mtk_dsi_poweroff(dsi);
+	/*
+	 * mtk_dsi_stop() and mtk_dsi_start() is asymmetric, since
+	 * mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(),
+	 * which needs irq for vblank, and mtk_dsi_stop() will disable irq.
+	 * mtk_dsi_start() needs to be called in mtk_output_dsi_enable(),
+	 * after dsi is fully set.
+	 */
+	mtk_dsi_stop(dsi);
+
+	mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500);
 
 	dsi->enabled = false;
 }
@@ -765,10 +756,26 @@ static void mtk_dsi_bridge_enable(struct drm_bridge *bridge)
 	mtk_output_dsi_enable(dsi);
 }
 
+static void mtk_dsi_bridge_pre_enable(struct drm_bridge *bridge)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+
+	mtk_dsi_poweron(dsi);
+}
+
+static void mtk_dsi_bridge_post_disable(struct drm_bridge *bridge)
+{
+	struct mtk_dsi *dsi = bridge_to_dsi(bridge);
+
+	mtk_dsi_poweroff(dsi);
+}
+
 static const struct drm_bridge_funcs mtk_dsi_bridge_funcs = {
 	.attach = mtk_dsi_bridge_attach,
 	.disable = mtk_dsi_bridge_disable,
 	.enable = mtk_dsi_bridge_enable,
+	.pre_enable = mtk_dsi_bridge_pre_enable,
+	.post_disable = mtk_dsi_bridge_post_disable,
 	.mode_set = mtk_dsi_bridge_mode_set,
 };
 
-- 
2.6.4