[PATCH v10 09/18] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

Andre Przywara andre.przywara at arm.com
Fri Feb 11 04:26:34 PST 2022


The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 512MiB/1GiB DDR3 DRAM
  - AXP305 PMIC
  - Raspberry-Pi-1 compatible GPIO header
  - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
  - 1 USB 2.0 host port
  - 1 USB 2.0 type C port (power supply + OTG)
  - MicroSD slot
  - on-board 2MiB bootable SPI NOR flash
  - 1Gbps Ethernet port (via RTL8211F PHY)
  - micro-HDMI port
  - unsupported Allwinner WiFi/BT chip

For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2

Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 203 ++++++++++++++++++
 2 files changed, 204 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 8fa5c060a4fe..df2214e6d946 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..ca07cae698ce
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy at 1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic at 745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.25.1




More information about the linux-arm-kernel mailing list