[PATCH v4 07/11] media: atmel: atmel-isc: change format propagation to subdev into only verification
Eugen.Hristev at microchip.com
Eugen.Hristev at microchip.com
Fri Feb 11 02:38:56 PST 2022
On 2/10/22 8:43 PM, Jacopo Mondi wrote:
> Hi Eugen
>
> On Fri, Jan 21, 2022 at 03:14:12PM +0200, Eugen Hristev wrote:
>> As a top MC video driver, the atmel-isc should not propagate the format to the
>> subdevice.
>> It should rather check at start_streaming() time if the subdev is properly
>> configured with a compatible format.
>> Removed the whole format finding logic, and reworked the format verification
>> at start_streaming time, such that the ISC will return an error if the subdevice
>> is not properly configured. To achieve this, media_pipeline_start
>> is called and a link_validate callback is created to check the formats.
>> With this being done, the module parameter 'sensor_preferred' makes no sense
>> anymore. The ISC should not decide which format the sensor is using. The
>> ISC should only cope with the situation and inform userspace if the streaming
>> is possible in the current configuration.
>
> This sounds right!
>
>> The redesign of the format propagation has also risen the question of the
>> enumfmt callback. If enumfmt is called with an mbus_code, the enumfmt handler
>> should only return the formats that are supported for this mbus_code.
>> To make it more easy to understand the formats, changed the report order
>> to report first the native formats, and after that the formats that the ISC
>> can convert to.
>>
>> Signed-off-by: Eugen Hristev <eugen.hristev at microchip.com>
>> ---
>> Changes in v4:
>> - moved validation code into link_validate and used media_pipeline_start
>> - merged this patch with the enum_fmt patch which was previously in v3 of
>> the series
>>
>> Changes in v3:
>> - clamp to maximum resolution once the frame size from the subdev is found
>>
>> drivers/media/platform/atmel/atmel-isc-base.c | 335 ++++++++++--------
>> .../media/platform/atmel/atmel-isc-scaler.c | 5 +
>> drivers/media/platform/atmel/atmel-isc.h | 3 +
>> 3 files changed, 191 insertions(+), 152 deletions(-)
>>
>> diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
>> index f7a88399bd54..31c79313aadc 100644
>> --- a/drivers/media/platform/atmel/atmel-isc-base.c
>> +++ b/drivers/media/platform/atmel/atmel-isc-base.c
>> @@ -36,11 +36,6 @@ static unsigned int debug;
>> module_param(debug, int, 0644);
>> MODULE_PARM_DESC(debug, "debug level (0-2)");
>>
>> -static unsigned int sensor_preferred = 1;
>> -module_param(sensor_preferred, uint, 0644);
>> -MODULE_PARM_DESC(sensor_preferred,
>> - "Sensor is preferred to output the specified format (1-on 0-off), default 1");
>> -
>> #define ISC_IS_FORMAT_RAW(mbus_code) \
>> (((mbus_code) & 0xf000) == 0x3000)
>>
>> @@ -337,6 +332,10 @@ static int isc_start_streaming(struct vb2_queue *vq, unsigned int count)
>> unsigned long flags;
>> int ret;
>>
>> + ret = media_pipeline_start(&isc->video_dev.entity, &isc->mpipe);
>> + if (ret)
>> + goto err_pipeline_start;
>> +
>> /* Enable stream on the sub device */
>> ret = v4l2_subdev_call(isc->current_subdev->sd, video, s_stream, 1);
>> if (ret && ret != -ENOIOCTLCMD) {
>> @@ -384,6 +383,9 @@ static int isc_start_streaming(struct vb2_queue *vq, unsigned int count)
>> v4l2_subdev_call(isc->current_subdev->sd, video, s_stream, 0);
>>
>> err_start_stream:
>> + media_pipeline_stop(&isc->video_dev.entity);
>> +
>> +err_pipeline_start:
>> spin_lock_irqsave(&isc->dma_queue_lock, flags);
>> list_for_each_entry(buf, &isc->dma_queue, list)
>> vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED);
>> @@ -420,6 +422,9 @@ static void isc_stop_streaming(struct vb2_queue *vq)
>> if (ret && ret != -ENOIOCTLCMD)
>> v4l2_err(&isc->v4l2_dev, "stream off failed in subdev\n");
>>
>> + /* Stop media pipeline */
>> + media_pipeline_stop(&isc->video_dev.entity);
>> +
>> /* Release all active buffers */
>> spin_lock_irqsave(&isc->dma_queue_lock, flags);
>> if (unlikely(isc->cur_frm)) {
>> @@ -496,21 +501,56 @@ static int isc_enum_fmt_vid_cap(struct file *file, void *priv,
>> u32 index = f->index;
>> u32 i, supported_index;
>>
>> - if (index < isc->controller_formats_size) {
>> - f->pixelformat = isc->controller_formats[index].fourcc;
>> - return 0;
>> + supported_index = 0;
>> +
>> + for (i = 0; i < isc->formats_list_size; i++) {
>> + if (!isc->formats_list[i].sd_support)
>> + continue;
>
> Sorry to ask again about sd_support, but if the ISC formats
> enumeration is not constrained to a specific mbus_code, shouldn't all
> the formats be enumerated regardless if they're supported from the
> sensor or not ?
Yes. this slipped a little. I have to rework a bit the format reporting
to user space.
>
>> + /*
>> + * If specific mbus_code is requested, provide only
>> + * supported formats with this mbus code
>> + */
>> + if (f->mbus_code && f->mbus_code !=
>> + isc->formats_list[i].mbus_code)
>
> nit: for clarity
> if (f->mbus_code &&
> f->mbus_code != isc->formats_list[i].mbus_code)
>
>> + continue;
>> + if (supported_index == index) {
>> + f->pixelformat = isc->formats_list[i].fourcc;
>> + return 0;
>> + }
>> + supported_index++;
>> }
>>
>> - index -= isc->controller_formats_size;
>> + /*
>> + * If the sensor does not support this mbus_code whatsoever,
>> + * there is no reason to advertise any of our output formats
>> + */
>> + if (supported_index == 0)
>> + return -EINVAL;
>>
>> + /*
>> + * If the sensor uses a format that is not raw, then we cannot
>> + * convert it to any of the formats that we usually can with a
>> + * RAW sensor. Thus, do not advertise them.
>> + */
>> + if (isc->config.sd_format &&
>> + !ISC_IS_FORMAT_RAW(isc->config.sd_format->mbus_code))
>> + return -EINVAL;
>> +
>> + /*
>> + * Iterate again through the formats that we can convert to.
>> + * However, to avoid duplicates, skip the formats that
>> + * the sensor already supports directly
>> + */
>> + index -= supported_index;
>> supported_index = 0;
>>
>> - for (i = 0; i < isc->formats_list_size; i++) {
>> - if (!ISC_IS_FORMAT_RAW(isc->formats_list[i].mbus_code) ||
>> - !isc->formats_list[i].sd_support)
>> + for (i = 0; i < isc->controller_formats_size; i++) {
>> + /* if this format is already supported by sensor, skip it */
>> + if (find_format_by_fourcc(isc, isc->controller_formats[i].fourcc))
>> continue;
>> if (supported_index == index) {
>> - f->pixelformat = isc->formats_list[i].fourcc;
>> + f->pixelformat =
>> + isc->controller_formats[i].fourcc;
>
> I trust this last part to work correctly, as it's not 100% clear to me :)
>
I think I will remove this and just report all the formats to userspace.
Let libcamera handle this ;)
>> return 0;
>> }
>> supported_index++;
>> @@ -581,20 +621,30 @@ static int isc_try_validate_formats(struct isc_device *isc)
>> break;
>> default:
>> /* any other different formats are not supported */
>> + v4l2_err(&isc->v4l2_dev, "Requested unsupported format.\n");
>> ret = -EINVAL;
>> }
>> v4l2_dbg(1, debug, &isc->v4l2_dev,
>> "Format validation, requested rgb=%u, yuv=%u, grey=%u, bayer=%u\n",
>> rgb, yuv, grey, bayer);
>>
>> - /* we cannot output RAW if we do not receive RAW */
>> - if ((bayer) && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
>> + if ((bayer) &&
>
> just 'bayer' ?
not sure what you mean ?
Have to check if we can output raw bayer , and we can only do that if we
receive raw bayer from the sensor.
>
>> + !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code)) {
>> + v4l2_err(&isc->v4l2_dev, "Cannot output RAW if we do not receive RAW.\n");
>> return -EINVAL;
>> + }
>>
>> - /* we cannot output GREY if we do not receive RAW/GREY */
>> if (grey && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code) &&
>> - !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code))
>> + !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
>> + v4l2_err(&isc->v4l2_dev, "Cannot output GREY if we do not receive RAW/GREY.\n");
>> + return -EINVAL;
>> + }
>> +
>> + if ((rgb || bayer || yuv) &&
>> + ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
>> + v4l2_err(&isc->v4l2_dev, "Cannot convert GREY to another format.\n");
>> return -EINVAL;
>> + }
>>
>> return ret;
>> }
>> @@ -822,7 +872,7 @@ static void isc_try_fse(struct isc_device *isc,
>> * If we do not know yet which format the subdev is using, we cannot
>> * do anything.
>> */
>> - if (!isc->try_config.sd_format)
>> + if (!isc->config.sd_format)
>> return;
>>
>> fse.code = isc->try_config.sd_format->mbus_code;
>> @@ -843,180 +893,141 @@ static void isc_try_fse(struct isc_device *isc,
>> }
>> }
>>
>> -static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f,
>> - u32 *code)
>> +static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f)
>> {
>> - int i;
>> - struct isc_format *sd_fmt = NULL, *direct_fmt = NULL;
>> struct v4l2_pix_format *pixfmt = &f->fmt.pix;
>> - struct v4l2_subdev_pad_config pad_cfg = {};
>> - struct v4l2_subdev_state pad_state = {
>> - .pads = &pad_cfg
>> - };
>> - struct v4l2_subdev_format format = {
>> - .which = V4L2_SUBDEV_FORMAT_TRY,
>> - };
>> - u32 mbus_code;
>> - int ret;
>> - bool rlp_dma_direct_dump = false;
>> + unsigned int i;
>>
>> if (f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
>> return -EINVAL;
>>
>> - /* Step 1: find a RAW format that is supported */
>> - for (i = 0; i < isc->num_user_formats; i++) {
>> - if (ISC_IS_FORMAT_RAW(isc->user_formats[i]->mbus_code)) {
>> - sd_fmt = isc->user_formats[i];
>> + isc->try_config.fourcc = isc->user_formats[0]->fourcc;
>> +
>> + /* find if the format requested is supported */
>> + for (i = 0; i < isc->controller_formats_size; i++)
>> + if (isc->controller_formats[i].fourcc == pixfmt->pixelformat) {
>> + isc->try_config.fourcc = pixfmt->pixelformat;
>> break;
>> }
>> - }
>> - /* Step 2: We can continue with this RAW format, or we can look
>> - * for better: maybe sensor supports directly what we need.
>> - */
>> - direct_fmt = find_format_by_fourcc(isc, pixfmt->pixelformat);
>> -
>> - /* Step 3: We have both. We decide given the module parameter which
>> - * one to use.
>> - */
>> - if (direct_fmt && sd_fmt && sensor_preferred)
>> - sd_fmt = direct_fmt;
>> -
>> - /* Step 4: we do not have RAW but we have a direct format. Use it. */
>> - if (direct_fmt && !sd_fmt)
>> - sd_fmt = direct_fmt;
>> -
>> - /* Step 5: if we are using a direct format, we need to package
>> - * everything as 8 bit data and just dump it
>> - */
>> - if (sd_fmt == direct_fmt)
>> - rlp_dma_direct_dump = true;
>> -
>> - /* Step 6: We have no format. This can happen if the userspace
>> - * requests some weird/invalid format.
>> - * In this case, default to whatever we have
>> - */
>> - if (!sd_fmt && !direct_fmt) {
>> - sd_fmt = isc->user_formats[isc->num_user_formats - 1];
>> - v4l2_dbg(1, debug, &isc->v4l2_dev,
>> - "Sensor not supporting %.4s, using %.4s\n",
>> - (char *)&pixfmt->pixelformat, (char *)&sd_fmt->fourcc);
>> - }
>> -
>> - if (!sd_fmt) {
>> - ret = -EINVAL;
>> - goto isc_try_fmt_err;
>> - }
>> -
>> - /* Step 7: Print out what we decided for debugging */
>> - v4l2_dbg(1, debug, &isc->v4l2_dev,
>> - "Preferring to have sensor using format %.4s\n",
>> - (char *)&sd_fmt->fourcc);
>> -
>> - /* Step 8: at this moment we decided which format the subdev will use */
>> - isc->try_config.sd_format = sd_fmt;
>> -
>> - /* Limit to Atmel ISC hardware capabilities */
>> - if (pixfmt->width > isc->max_width)
>> - pixfmt->width = isc->max_width;
>> - if (pixfmt->height > isc->max_height)
>> - pixfmt->height = isc->max_height;
>> -
>> - /*
>> - * The mbus format is the one the subdev outputs.
>> - * The pixels will be transferred in this format Sensor -> ISC
>> - */
>> - mbus_code = sd_fmt->mbus_code;
>> -
>> - /*
>> - * Validate formats. If the required format is not OK, default to raw.
>> - */
>> -
>> - isc->try_config.fourcc = pixfmt->pixelformat;
>> -
>> - if (isc_try_validate_formats(isc)) {
>> - pixfmt->pixelformat = isc->try_config.fourcc = sd_fmt->fourcc;
>> - /* Re-try to validate the new format */
>> - ret = isc_try_validate_formats(isc);
>> - if (ret)
>> - goto isc_try_fmt_err;
>> - }
>> -
>> - ret = isc_try_configure_rlp_dma(isc, rlp_dma_direct_dump);
>> - if (ret)
>> - goto isc_try_fmt_err;
>> -
>> - ret = isc_try_configure_pipeline(isc);
>> - if (ret)
>> - goto isc_try_fmt_err;
>>
>> - /* Obtain frame sizes if possible to have crop requirements ready */
>> - isc_try_fse(isc, &pad_state);
>> -
>> - v4l2_fill_mbus_format(&format.format, pixfmt, mbus_code);
>> - ret = v4l2_subdev_call(isc->current_subdev->sd, pad, set_fmt,
>> - &pad_state, &format);
>> - if (ret < 0)
>> - goto isc_try_fmt_subdev_err;
>> + /* If we did not find the requested format, we will fallback here */
>> + pixfmt->pixelformat = isc->try_config.fourcc;
>> + pixfmt->colorspace = V4L2_COLORSPACE_SRGB;
>> + pixfmt->field = V4L2_FIELD_NONE;
>>
>> - v4l2_fill_pix_format(pixfmt, &format.format);
>> + isc_try_configure_rlp_dma(isc, false);
>>
>> /* Limit to Atmel ISC hardware capabilities */
>> - if (pixfmt->width > isc->max_width)
>> - pixfmt->width = isc->max_width;
>> - if (pixfmt->height > isc->max_height)
>> - pixfmt->height = isc->max_height;
>> + v4l_bound_align_image(&pixfmt->width, 16, isc->max_width, 0,
>> + &pixfmt->height, 16, isc->max_height, 0, 0);
>>
>> pixfmt->field = V4L2_FIELD_NONE;
>> pixfmt->bytesperline = (pixfmt->width * isc->try_config.bpp_v4l2) >> 3;
>> pixfmt->sizeimage = ((pixfmt->width * isc->try_config.bpp) >> 3) *
>> pixfmt->height;
>
> Seems pixfmt->field is set twice.
>
> Could you move the assignment of all pixfmt to a single block ?
okay
>
>>
>> - if (code)
>> - *code = mbus_code;
>> + isc->try_fmt = *f;
>>
>> return 0;
>> +}
>>
>> -isc_try_fmt_err:
>> - v4l2_err(&isc->v4l2_dev, "Could not find any possible format for a working pipeline\n");
>> -isc_try_fmt_subdev_err:
>> - memset(&isc->try_config, 0, sizeof(isc->try_config));
>> +static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
>> +{
>> + isc_try_fmt(isc, f);
>>
>> - return ret;
>> + /* make the try configuration active */
>> + isc->config = isc->try_config;
>> + isc->fmt = isc->try_fmt;
>> +
>> + v4l2_dbg(1, debug, &isc->v4l2_dev, "ISC set_fmt to %.4s @%dx%d\n",
>> + (char *)&f->fmt.pix.pixelformat,
>> + f->fmt.pix.width, f->fmt.pix.height);
>> +
>> + return 0;
>> }
>>
>> -static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
>> +static int isc_validate(struct isc_device *isc)
>> {
>> + int ret;
>> + int i;
>> + struct isc_format *sd_fmt = NULL;
>> + struct v4l2_pix_format *pixfmt = &isc->fmt.fmt.pix;
>> struct v4l2_subdev_format format = {
>> .which = V4L2_SUBDEV_FORMAT_ACTIVE,
>> + .pad = isc->remote_pad,
>> + };
>> + struct v4l2_subdev_pad_config pad_cfg = {};
>> + struct v4l2_subdev_state pad_state = {
>> + .pads = &pad_cfg,
>> };
>> - u32 mbus_code = 0;
>> - int ret;
>>
>> - ret = isc_try_fmt(isc, f, &mbus_code);
>> + /* Get current format from subdev */
>> + ret = v4l2_subdev_call(isc->current_subdev->sd, pad, get_fmt, NULL,
>> + &format);
>> if (ret)
>> return ret;
>>
>> - v4l2_fill_mbus_format(&format.format, &f->fmt.pix, mbus_code);
>> - ret = v4l2_subdev_call(isc->current_subdev->sd, pad,
>> - set_fmt, NULL, &format);
>> - if (ret < 0)
>> - return ret;
>> + /* Identify the subdev's format configuration */
>> + for (i = 0; i < isc->num_user_formats; i++)
>> + if (isc->user_formats[i]->mbus_code == format.format.code) {
>> + sd_fmt = isc->user_formats[i];
>> + break;
>> + }
>> +
>> + /* Check if the format is not supported */
>> + if (!sd_fmt) {
>> + v4l2_err(&isc->v4l2_dev,
>> + "Current subdevice is streaming a media bus code that is not supported 0x%x\n",
>> + format.format.code);
>> + return -EPIPE;
>> + }
>> +
>> + /* At this moment we know which format the subdev will use */
>> + isc->try_config.sd_format = sd_fmt;
>> +
>> + /* If the sensor is not RAW, we can only do a direct dump */
>> + if (!ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
>> + isc_try_configure_rlp_dma(isc, true);
>>
>> /* Limit to Atmel ISC hardware capabilities */
>> - if (f->fmt.pix.width > isc->max_width)
>> - f->fmt.pix.width = isc->max_width;
>> - if (f->fmt.pix.height > isc->max_height)
>> - f->fmt.pix.height = isc->max_height;
>> + v4l_bound_align_image(&format.format.width, 16, isc->max_width, 0,
>> + &format.format.height, 16, isc->max_height, 0, 0);
>> +
>> + /* Check if the frame size is the same. Otherwise we may overflow */
>> + if (pixfmt->height != format.format.height ||
>> + pixfmt->width != format.format.width) {
>> + v4l2_err(&isc->v4l2_dev,
>> + "ISC not configured with the proper frame size: %dx%d\n",
>> + format.format.width, format.format.height);
>> + return -EPIPE;
>> + }
>>
>> - isc->fmt = *f;
>> + v4l2_dbg(1, debug, &isc->v4l2_dev,
>> + "Identified subdev using format %.4s with %dx%d %d bpp\n",
>> + (char *)&sd_fmt->fourcc, pixfmt->width, pixfmt->height,
>> + isc->try_config.bpp);
>>
>> + /* Reset and restart AWB if the subdevice changed the format */
>> if (isc->try_config.sd_format && isc->config.sd_format &&
>> isc->try_config.sd_format != isc->config.sd_format) {
>> isc->ctrls.hist_stat = HIST_INIT;
>> isc_reset_awb_ctrls(isc);
>> isc_update_v4l2_ctrls(isc);
>> }
>> - /* make the try configuration active */
>> +
>> + /* Validate formats */
>> + ret = isc_try_validate_formats(isc);
>> + if (ret)
>> + return ret;
>> +
>> + /* Obtain frame sizes if possible to have crop requirements ready */
>> + isc_try_fse(isc, &pad_state);
>> +
>> + /* Configure ISC pipeline for the config */
>> + ret = isc_try_configure_pipeline(isc);
>> + if (ret)
>> + return ret;
>> +
>> isc->config = isc->try_config;
>>
>> v4l2_dbg(1, debug, &isc->v4l2_dev, "New ISC configuration in place\n");
>> @@ -1040,7 +1051,7 @@ static int isc_try_fmt_vid_cap(struct file *file, void *priv,
>> {
>> struct isc_device *isc = video_drvdata(file);
>>
>> - return isc_try_fmt(isc, f, NULL);
>> + return isc_try_fmt(isc, f);
>> }
>>
>> static int isc_enum_input(struct file *file, void *priv,
>> @@ -1841,7 +1852,7 @@ static int isc_set_default_fmt(struct isc_device *isc)
>> };
>> int ret;
>>
>> - ret = isc_try_fmt(isc, &f, NULL);
>> + ret = isc_try_fmt(isc, &f);
>> if (ret)
>> return ret;
>>
>> @@ -2015,6 +2026,24 @@ int isc_pipeline_init(struct isc_device *isc)
>> }
>> EXPORT_SYMBOL_GPL(isc_pipeline_init);
>>
>> +int isc_link_validate(struct media_link *link)
>> +{
>> + struct video_device *vdev =
>> + media_entity_to_video_device(link->sink->entity);
>> + struct isc_device *isc = video_get_drvdata(vdev);
>> + int ret;
>> +
>> + ret = v4l2_subdev_link_validate(link);
>> + if (ret)
>> + return ret;
>
> Doesn't v4l2_subdev_link_validate() call
> v4l2_subdev_link_validate_default() if you don't define a .link_validate()
> pad operation ? v4l2_subdev_link_validate_default() compares format
> and sizes of both ends to the links and want them to be identical,
> something that defeat the purpose of your custom isc_validate() ?
I think so. However if I replace the validate call with my custom one, I
thought that the old default should be called as well.
Meaning, that maybe my custom validation does certain isc-related
checks, while the v4l2_subdev_link_validate does exactly what you said.
So, by defining a custom link_validate, do I lose the checks that are
done by the v4l2_subdev_link_validate ?
That's what I wanted to avoid. Chip in my checks, but keep the v4l2
standard validation in place.
Does that make sense ?
> Thanks
> j
>
>> +
>> + return isc_validate(isc);
>> +}
>> +
>> +static const struct media_entity_operations isc_entity_operations = {
>> + .link_validate = isc_link_validate,
>> +};
>> +
> };
>> int isc_mc_init(struct isc_device *isc, u32 ver)
>> {
>> const struct of_device_id *match;
>> @@ -2022,6 +2051,8 @@ int isc_mc_init(struct isc_device *isc, u32 ver)
>>
>> isc->video_dev.entity.function = MEDIA_ENT_F_IO_V4L;
>> isc->video_dev.entity.flags = MEDIA_ENT_FL_DEFAULT;
>> + isc->video_dev.entity.ops = &isc_entity_operations;
>> +
>> isc->pads[ISC_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
>>
>> ret = media_entity_pads_init(&isc->video_dev.entity, ISC_PADS_NUM,
>> diff --git a/drivers/media/platform/atmel/atmel-isc-scaler.c b/drivers/media/platform/atmel/atmel-isc-scaler.c
>> index ec95c9665883..93375a61aea6 100644
>> --- a/drivers/media/platform/atmel/atmel-isc-scaler.c
>> +++ b/drivers/media/platform/atmel/atmel-isc-scaler.c
>> @@ -155,6 +155,10 @@ static const struct v4l2_subdev_pad_ops isc_scaler_pad_ops = {
>> .init_cfg = isc_scaler_init_cfg,
>> };
>>
>> +static const struct media_entity_operations isc_scaler_entity_ops = {
>> + .link_validate = v4l2_subdev_link_validate,
>> +};
>> +
>> static const struct v4l2_subdev_ops xisc_scaler_subdev_ops = {
>> .pad = &isc_scaler_pad_ops,
>> };
>> @@ -172,6 +176,7 @@ int isc_scaler_init(struct isc_device *isc)
>>
>> isc->scaler_sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
>> isc->scaler_sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_SCALER;
>> + isc->scaler_sd.entity.ops = &isc_scaler_entity_ops;
>> isc->scaler_pads[ISC_SCALER_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
>> isc->scaler_pads[ISC_SCALER_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
>>
>> diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
>> index 04ea5e340808..e36cf9d3942a 100644
>> --- a/drivers/media/platform/atmel/atmel-isc.h
>> +++ b/drivers/media/platform/atmel/atmel-isc.h
>> @@ -270,6 +270,7 @@ enum isc_scaler_pads {
>> * @formats_list_size: size of formats_list array
>> * @pads: media controller pads for isc video entity
>> * @mdev: media device that is registered by the isc
>> + * @mpipe: media device pipeline used by the isc
>> * @remote_pad: remote pad on the connected subdevice
>> * @scaler_sd: subdevice for the scaler that isc registers
>> * @scaler_pads: media controller pads for the scaler subdevice
>> @@ -295,6 +296,7 @@ struct isc_device {
>> struct completion comp;
>>
>> struct v4l2_format fmt;
>> + struct v4l2_format try_fmt;
>> struct isc_format **user_formats;
>> unsigned int num_user_formats;
>>
>> @@ -366,6 +368,7 @@ struct isc_device {
>> struct {
>> struct media_pad pads[ISC_PADS_NUM];
>> struct media_device mdev;
>> + struct media_pipeline mpipe;
>>
>> u32 remote_pad;
>> };
>> --
>> 2.25.1
>>
More information about the linux-arm-kernel
mailing list