[RFC 2/2] PCI: imx6: Enable imx6qp pcie power management support

[Hongxing Zhu]

> -----Original Message-----
> From: Bjorn Helgaas <helgaas at kernel.org>
> Sent: 2022年2月11日 6:05
> To: Hongxing Zhu <hongxing.zhu at nxp.com>
> Cc: l.stach at pengutronix.de; bhelgaas at google.com;
> lorenzo.pieralisi at arm.com; shawnguo at kernel.org; linux-pci at vger.kernel.org;
> linux-arm-kernel at lists.infradead.org; linux-kernel at vger.kernel.org;
> kernel at pengutronix.de; dl-linux-imx <linux-imx at nxp.com>
> Subject: Re: [RFC 2/2] PCI: imx6: Enable imx6qp pcie power management
> support
> 
> On Thu, Feb 10, 2022 at 03:23:19AM +0000, Hongxing Zhu wrote:
> > > -----Original Message-----
> > > From: Bjorn Helgaas <helgaas at kernel.org>
> > > Sent: 2022年2月9日 23:37
> > > To: Hongxing Zhu <hongxing.zhu at nxp.com>
> > > Cc: l.stach at pengutronix.de; bhelgaas at google.com;
> > > lorenzo.pieralisi at arm.com; shawnguo at kernel.org;
> > > linux-pci at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> > > linux-kernel at vger.kernel.org; kernel at pengutronix.de; dl-linux-imx
> > > <linux-imx at nxp.com>
> > > Subject: Re: [RFC 2/2] PCI: imx6: Enable imx6qp pcie power
> > > management support
> > >
> > > On Wed, Feb 09, 2022 at 03:02:36PM +0800, Richard Zhu wrote:
> > > > i.MX6QP PCIe supports the RESET logic, thus it can support the L2
> > > > exit by the reset mechanism.
> > > > Enable the i.MX6QP PCIe suspend/resume operations support.
> 
> > > What does "L2 exit by reset mechanism" mean?  Is this an
> > > i.MX6-specific thing?  If not, can you point me to the relevant part
> > > of the PCIe spec?
> >
> > No, it's not i.MX6 specific thing. i.MX6Q/DL doesn't have the
> > self-reset mechanism.  Thus, it can't reset itself to an initialized
> > stat when link exit from the L2 or L3 stats.  i.MX6QP PCIe has the
> > self-reset mechanism, and it can reset itself when link exit from L2
> > or L3 stats.  The commit description might not accurate.  How about
> > change them to "i.MX6QP PCIe supports the RESET logic, thus it can
> > reset itself to the initialized stat when exit from L2 or L3 stats."
> 
> s/stat/state/
Thanks for your quickly reply.
Got that, would be changed later.
> 
> Ugh, I have all sorts of questions now, but I don't think I want to know much
> more about this ;)
> 
> Seems like this device requires software assist when bringing the link out of L2
> or L3.  Is that allowed per PCIe spec, or is this an erratum?
> 
> Does this mean the driver needs to be involved when we take a device out of
> D3 (where the link was in L2 or L3)?

Yes, the SW should be involved when bringing the link out of L2 or L3.
I looked through the SPEC, didn't find that they are forbidden by SPEC.
It might be a design limitation, I think.

Best Regards
Richard Zhu

> 
> Bjorn