[PATCH v2 65/66] ARM: dts: sun8i: v3s: Add support for the ISP

Paul Kocialkowski paul.kocialkowski at bootlin.com
Sat Feb 5 10:54:28 PST 2022


The V3s (and related platforms) come with an instance of the A31 ISP.
Even though it is very close to the A31 ISP, it is not exactly
register-compatible and a dedicated compatible only is used as a
result.

Just like most other blocks of the camera pipeline, the ISP uses
the common CSI bus, module and ram clock as well as reset.

A port connection to the ISP is added to CSI0 for convenience since
CSI0 serves for MIPI CSI-2 interface support, which is likely to
receive raw data that will need to be processed by the ISP to produce
a final image.

While the interconnects property is used to inherit the proper dma
ranges, the associated index for the cell is set to 0 since no
particular meaning is attached to it. This might need to be changed
later on (when identifying a proper mbus channel becomes relevant,
e.g. for things like QoS).

Signed-off-by: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 35 ++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index f5f7dfec49f9..c2e65679b9ed 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -638,6 +638,14 @@ csi0_in_mipi_csi2: endpoint {
 						remote-endpoint = <&mipi_csi2_out_csi0>;
 					};
 				};
+
+				port at 2 {
+					reg = <2>;
+
+					csi0_out_isp: endpoint {
+						remote-endpoint = <&isp_in_csi0>;
+					};
+				};
 			};
 		};
 
@@ -696,5 +704,32 @@ csi1: camera at 1cb4000 {
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
 		};
+
+		isp: isp at 1cb8000 {
+			compatible = "allwinner,sun8i-v3s-isp";
+			reg = <0x01cb8000 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			interconnects = <&mbus 0>;
+			interconnect-names = "dma-mem";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+
+					isp_in_csi0: endpoint {
+						remote-endpoint = <&csi0_out_isp>;
+					};
+				};
+			};
+		};
 	};
 };
-- 
2.34.1




More information about the linux-arm-kernel mailing list