[PATCH v1 1/5] ARM: dts: imx6sl: use tabs for code indent

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler at toradex.com>

This fixes the following error:

arch/arm/boot/dts/imx6sl.dtsi:714: error: code indent should use tabs
where possible

Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
---

 arch/arm/boot/dts/imx6sl.dtsi | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 06a515121dfc..271f4b971a83 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -61,10 +61,10 @@ cpu0: cpu at 0 {
 				<792000  1175000>,
 				<396000  975000>;
 			fsl,soc-operating-points =
-				/* ARM kHz      SOC-PU uV */
-				<996000         1225000>,
-				<792000         1175000>,
-				<396000         1175000>;
+				/* ARM kHz	SOC-PU uV */
+				<996000		1225000>,
+				<792000		1175000>,
+				<396000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>,
@@ -222,7 +222,7 @@ ecspi4: spi at 2014000 {
 
 				uart5: serial at 2018000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -235,7 +235,7 @@ uart5: serial at 2018000 {
 
 				uart1: serial at 2020000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -248,7 +248,7 @@ uart1: serial at 2020000 {
 
 				uart2: serial at 2024000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -309,7 +309,7 @@ ssi3: ssi at 2030000 {
 
 				uart3: serial at 2034000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02034000 0x4000>;
 					interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -322,7 +322,7 @@ uart3: serial at 2034000 {
 
 				uart4: serial at 2038000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02038000 0x4000>;
 					interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -711,7 +711,7 @@ pd_pu: power-domain at 1 {
 						#power-domain-cells = <0>;
 						power-supply = <&reg_pu>;
 						clocks = <&clks IMX6SL_CLK_GPU2D_OVG>,
-						         <&clks IMX6SL_CLK_GPU2D_PODF>;
+							 <&clks IMX6SL_CLK_GPU2D_PODF>;
 					};
 
 					pd_disp: power-domain at 2 {
-- 
2.36.1