[PATCH v26 07/10] soc: mediatek: mmsys: add mmsys for support 64 reset bits
Nancy.Lin
nancy.lin at mediatek.com
Wed Aug 24 19:19:58 PDT 2022
Hi Matthias,
Thanks for your comment.
On Wed, 2022-08-24 at 13:41 +0200, Matthias Brugger wrote:
>
> On 24/08/2022 04:44, Nancy.Lin wrote:
> > Hi Matthias,
> >
> > Thanks for your comment.
> >
> > On Tue, 2022-08-23 at 14:08 +0200, Matthias Brugger wrote:
> > >
> > > On 23/08/2022 13:30, Nancy.Lin wrote:
> > > > Hi Matthias,
> > > >
> > > > Thanks for the review.
> > > >
> > > > On Tue, 2022-08-23 at 12:20 +0200, Matthias Brugger wrote:
> > > > >
> > > > > On 19/08/2022 08:10, Nancy.Lin wrote:
> > > > > > Add mmsys for support 64 reset bits. It is a preparation
> > > > > > for
> > > > > > MT8195
> > > > > > vdosys1 HW reset. MT8195 vdosys1 has more than 32 reset
> > > > > > bits.
> > > > > >
> > > > > > 1. Add the number of reset bits in mmsys private data
> > > > > > 2. move the whole "reset register code section" behind the
> > > > > > "get mmsys->data" code section for getting the num_resets
> > > > > > in
> > > > > > mmsys-
> > > > > > > data.
> > > > > >
> > > > > > Signed-off-by: Nancy.Lin <nancy.lin at mediatek.com>
> > > > > > Reviewed-by: AngeloGioacchino Del Regno <
> > > > > > angelogioacchino.delregno at collabora.com>
> > > > > > Reviewed-by: CK Hu <ck.hu at mediatek.com>
> > > > > > Tested-by: Bo-Chen Chen <rex-bc.chen at mediatek.com>
> > > > > > ---
> > > > > > drivers/soc/mediatek/mtk-mmsys.c | 40
> > > > > > +++++++++++++++++++++-
> > > > > > ---
> > > > > > -------
> > > > > > drivers/soc/mediatek/mtk-mmsys.h | 1 +
> > > > > > 2 files changed, 27 insertions(+), 14 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/soc/mediatek/mtk-mmsys.c
> > > > > > b/drivers/soc/mediatek/mtk-mmsys.c
> > > > > > index 999be064103b..20ae751ad8a7 100644
> > > > > > --- a/drivers/soc/mediatek/mtk-mmsys.c
> > > > > > +++ b/drivers/soc/mediatek/mtk-mmsys.c
> > > > > > @@ -20,6 +20,8 @@
> > > > > > #include "mt8195-mmsys.h"
> > > > > > #include "mt8365-mmsys.h"
> > > > > >
> > > > > > +#define MMSYS_SW_RESET_PER_REG 32
> > > > > > +
> > > > > > static const struct mtk_mmsys_driver_data
> > > > > > mt2701_mmsys_driver_data = {
> > > > > > .clk_driver = "clk-mt2701-mm",
> > > > > > .routes = mmsys_default_routing_table,
> > > > > > @@ -86,6 +88,7 @@ static const struct mtk_mmsys_driver_data
> > > > > > mt8173_mmsys_driver_data = {
> > > > > > .routes = mmsys_default_routing_table,
> > > > > > .num_routes =
> > > > > > ARRAY_SIZE(mmsys_default_routing_table),
> > > > > > .sw0_rst_offset = MT8183_MMSYS_SW0_RST_B,
> > > > > > + .num_resets = 32,
> > > > > > };
> > > > > >
> > > > > > static const struct mtk_mmsys_match_data
> > > > > > mt8173_mmsys_match_data
> > > > > > = {
> > > > > > @@ -100,6 +103,7 @@ static const struct
> > > > > > mtk_mmsys_driver_data
> > > > > > mt8183_mmsys_driver_data = {
> > > > > > .routes = mmsys_mt8183_routing_table,
> > > > > > .num_routes =
> > > > > > ARRAY_SIZE(mmsys_mt8183_routing_table),
> > > > > > .sw0_rst_offset = MT8183_MMSYS_SW0_RST_B,
> > > > > > + .num_resets = 32,
> > > > > > };
> > > > > >
> > > > > > static const struct mtk_mmsys_match_data
> > > > > > mt8183_mmsys_match_data
> > > > > > = {
> > > > > > @@ -114,6 +118,7 @@ static const struct
> > > > > > mtk_mmsys_driver_data
> > > > > > mt8186_mmsys_driver_data = {
> > > > > > .routes = mmsys_mt8186_routing_table,
> > > > > > .num_routes =
> > > > > > ARRAY_SIZE(mmsys_mt8186_routing_table),
> > > > > > .sw0_rst_offset = MT8186_MMSYS_SW0_RST_B,
> > > > > > + .num_resets = 32,
> > > > > > };
> > > > > >
> > > > > > static const struct mtk_mmsys_match_data
> > > > > > mt8186_mmsys_match_data
> > > > > > = {
> > > > > > @@ -128,6 +133,7 @@ static const struct
> > > > > > mtk_mmsys_driver_data
> > > > > > mt8192_mmsys_driver_data = {
> > > > > > .routes = mmsys_mt8192_routing_table,
> > > > > > .num_routes =
> > > > > > ARRAY_SIZE(mmsys_mt8192_routing_table),
> > > > > > .sw0_rst_offset = MT8186_MMSYS_SW0_RST_B,
> > > > > > + .num_resets = 32,
> > > > >
> > > > > You didn't reply to Nicolas regarding the reset numbers. I
> > > > > actually
> > > > > agree with
> > > > > him that we will need the num_resets declared for all
> > > > > devices.
> > > > > Why do
> > > > > you think
> > > > > this is not the case?
> > > > >
> > > > > Regards,
> > > > > Matthias
> > > > >
> > > >
> > > > Sorry, I lost Nicolas's email.
> > > >
> > > > I checked with the mmsys git log with reset controller
> > > > function.
> > > >
> > > > 1. Enric add mmsys reset controller function in [1]/[2].
> > > > => in mtk_mmsys_reset_update(), all mmsys reset offset is
> > > > MMSYS_SW0_RST_B (0x140).
> > > >
> > > > 2. After Enric's patch, Rex add sw0_rst_offset in mmsys driver
> > > > data
> > > > in
> > > > [3].
> > > >
> > > > So, I think sw0_rst_offset is not zero. Instead of only add
> > > > num_resets
> > > > but also need to add sw0_rst_offset for all mmsys. What do you
> > > > think ?
> > > >
> > >
> > > Good point. It seems we have a bug in the driver. Either all SoCs
> > > have the
> > > reset, but it's broken since
> > > 62dc30150c06 ("soc: mediatek: mmsys: add sw0_rst_offset in mmsys
> > > driver data")
> > > or we are adding a reset controller independently if the silicon
> > > has
> > > one, which
> > > would be an error in:
> > > f27ef2856343 ("soc: mediatek: mmsys: Add reset controller
> > > support")
> > >
> > > We have to find that out.
> > >
> > > Regards,
> > > Matthias
> >
> >
> > In [2], I think the first revision of Enric's reset controller is
> > added
> > for 8173 and 8183, not for all mmsys device.
> > =>[v3,4/7] arm64: dts: mt8173: Add the mmsys reset bit to
> > reset the
> > dsi0
> > =>[v3,5/7] arm64: dts: mt8183: Add the mmsys reset bit to
> > reset the
> > dsi0
> >
> > In [3], Rex only add sw0_rst_offset in 8173 and 8183 mmsys driver
> > data.
> > >
> >
> > For other SoCs, like mt2701,mt2712..., these SoCs even don't define
> > mmsys hw reset bit[4]. So I think only set the num_resets to 32 or
> > 64
> > to those mmsys devices who really need the reset control, others
> > set to
> > 0(same as my v26 patch).
> >
>
> Thanks for looking into this, please see my comment further below.
>
>
> >
> > [4]mt2701-resets.h
> >
https://urldefense.com/v3/__https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/dt-bindings/reset/mt2701-resets.h?id=62dc30150c06774a8122c52aedd0eddaceaf5940__;!!CTRNKA9wMg0ARbw!3j1YotescyEb7vq_dITIlc-FdtaFSslPkcn3B-Sw95Zf613Z-TPG4FK0BdCyW0Fb$
> >
> >
> > Regards,
> > Nancy
> >
> >
> > > > [1]
> > > >
> >
> >
https://urldefense.com/v3/__https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/soc/mediatek/mtk-mmsys.c?id=f27ef2856343e2ddc392975d7b15120442e4d7b7__;!!CTRNKA9wMg0ARbw!3cWAYlD1mrWRmNZy0zoJs8MNiD3s7K9PteJI9cGEvu_qp3VShfqxsBTb_fKynszs$
> > > >
> > > > [2]
> > > >
> > > >
> >
> >
https://urldefense.com/v3/__https://patchwork.kernel.org/project/linux-mediatek/cover/20210825102632.601614-1-enric.balletbo@collabora.com/__;!!CTRNKA9wMg0ARbw!3cWAYlD1mrWRmNZy0zoJs8MNiD3s7K9PteJI9cGEvu_qp3VShfqxsBTb_cH-3nM8$
> > > >
> > > > [3]
> > > >
> > > >
> >
> >
https://urldefense.com/v3/__https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/soc/mediatek/mtk-mmsys.c?id=62dc30150c06774a8122c52aedd0eddaceaf5940__;!!CTRNKA9wMg0ARbw!3cWAYlD1mrWRmNZy0zoJs8MNiD3s7K9PteJI9cGEvu_qp3VShfqxsBTb_VXEsbNa$
> > > >
> > > >
> > > > Regards,
> > > > Nancy
> > > > >
> > > > > > };
> > > > > >
> > > > > > static const struct mtk_mmsys_match_data
> > > > > > mt8192_mmsys_match_data
> > > > > > = {
> > > > > > @@ -288,13 +294,19 @@ static int
> > > > > > mtk_mmsys_reset_update(struct
> > > > > > reset_controller_dev *rcdev, unsigned l
> > > > > > {
> > > > > > struct mtk_mmsys *mmsys = container_of(rcdev,
> > > > > > struct
> > > > > > mtk_mmsys,
> > > > > > rcdev);
> > > > > > unsigned long flags;
> > > > > > + u32 offset;
> > > > > > + u32 reg;
> > > > > > +
> > > > > > + offset = (id / MMSYS_SW_RESET_PER_REG) * sizeof(u32);
> > > > > > + id = id % MMSYS_SW_RESET_PER_REG;
> > > > > > + reg = mmsys->data->sw0_rst_offset + offset;
> > > > > >
> > > > > > spin_lock_irqsave(&mmsys->lock, flags);
> > > > > >
> > > > > > if (assert)
> > > > > > - mtk_mmsys_update_bits(mmsys, mmsys->data-
> > > > > > > sw0_rst_offset, BIT(id), 0, NULL);
> > > > > >
> > > > > > + mtk_mmsys_update_bits(mmsys, reg, BIT(id), 0,
> > > > > > NULL);
> > > > > > else
> > > > > > - mtk_mmsys_update_bits(mmsys, mmsys->data-
> > > > > > > sw0_rst_offset, BIT(id), BIT(id), NULL);
> > > > > >
> > > > > > + mtk_mmsys_update_bits(mmsys, reg, BIT(id),
> > > > > > BIT(id),
> > > > > > NULL);
> > > > > >
> > > > > > spin_unlock_irqrestore(&mmsys->lock, flags);
> > > > > >
> > > > > > @@ -351,18 +363,6 @@ static int mtk_mmsys_probe(struct
> > > > > > platform_device *pdev)
> > > > > > return ret;
> > > > > > }
> > > > > >
> > > > > > - spin_lock_init(&mmsys->lock);
> > > > > > -
> > > > > > - mmsys->rcdev.owner = THIS_MODULE;
> > > > > > - mmsys->rcdev.nr_resets = 32;
> > > > > > - mmsys->rcdev.ops = &mtk_mmsys_reset_ops;
> > > > > > - mmsys->rcdev.of_node = pdev->dev.of_node;
> > > > > > - ret = devm_reset_controller_register(&pdev->dev,
> > > > > > &mmsys-
> > > > > > > rcdev);
> > > > > >
> > > > > > - if (ret) {
> > > > > > - dev_err(&pdev->dev, "Couldn't register mmsys
> > > > > > reset
> > > > > > controller: %d\n", ret);
> > > > > > - return ret;
> > > > > > - }
> > > > > > -
> > > > > > res = platform_get_resource(pdev,
> > > > > > IORESOURCE_MEM, 0);
> > > > > > if (!res) {
> > > > > > dev_err(dev, "Couldn't get mmsys
> > > > > > resource\n");
> > > > > > @@ -384,6 +384,18 @@ static int mtk_mmsys_probe(struct
> > > > > > platform_device *pdev)
> > > > > > mmsys->data = match_data->drv_data[0];
> > > > > > }
> > > > > >
> > > > > > + spin_lock_init(&mmsys->lock);
> > > > > > +
> > > > > > + mmsys->rcdev.owner = THIS_MODULE;
> > > > > > + mmsys->rcdev.nr_resets = mmsys->data->num_resets;
> > > > > > + mmsys->rcdev.ops = &mtk_mmsys_reset_ops;
> > > > > > + mmsys->rcdev.of_node = pdev->dev.of_node;
> > > > > > + ret = devm_reset_controller_register(&pdev->dev,
> > > > > > &mmsys-
> > > > > > > rcdev);
> > > > > >
> > > > > > + if (ret) {
> > > > > > + dev_err(&pdev->dev, "Couldn't register mmsys
> > > > > > reset
> > > > > > controller: %d\n", ret);
> > > > > > + return ret;
> > > > > > + }
> > > > > > +
>
>
> This code is only relevant if mmsys->data->num_resets > 0. Let's
> check for that
> before setting up and registering an interrupt controller. What do
> you think?
>
> Regards,
> Matthias
>
There is no doubt that we need to check num_resets > 0 before
registering reset controller.
I will add it in the next revision.
Regards,
Nancy
> > > > > > #if IS_REACHABLE(CONFIG_MTK_CMDQ)
> > > > > > ret = cmdq_dev_get_client_reg(dev, &mmsys-
> > > > > > >cmdq_base,
> > > > > > 0);
> > > > > > if (ret)
> > > > > > diff --git a/drivers/soc/mediatek/mtk-mmsys.h
> > > > > > b/drivers/soc/mediatek/mtk-mmsys.h
> > > > > > index f01ba206481d..20a271b80b3b 100644
> > > > > > --- a/drivers/soc/mediatek/mtk-mmsys.h
> > > > > > +++ b/drivers/soc/mediatek/mtk-mmsys.h
> > > > > > @@ -92,6 +92,7 @@ struct mtk_mmsys_driver_data {
> > > > > > const struct mtk_mmsys_routes *routes;
> > > > > > const unsigned int num_routes;
> > > > > > const u16 sw0_rst_offset;
> > > > > > + const u32 num_resets;
> > > > > > };
> > > > > >
> > > > > > struct mtk_mmsys_match_data {
> > > > >
> > > > >
>
>
More information about the linux-arm-kernel
mailing list