[PATCH v3 07/19] pinctrl: rockchip: Add RV1126 pinctrl support
Jagan Teki
jagan at edgeble.ai
Thu Aug 18 05:41:20 PDT 2022
RV1126 has five GPIOs groups - GPIO0 in PD_MMU and GPIO1-4
in PD_BUS.
In GPIO0, up to Lower C group GPIO0_C[3:0] is part of PMU
but rest of the groups from there are part of GRF.
Added pinctrl support for RV1126 and the pull, drv and schmitt
calculations are inferred from [1] authored by Jianqun Xu.
[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/pinctrl/pinctrl-rockchip.c
Cc: linux-gpio at vger.kernel.org
Cc: Linus Walleij <linus.walleij at linaro.org>
Signed-off-by: Jianqun Xu <jay.xu at rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang at rock-chips.com>
Signed-off-by: Jagan Teki <jagan at edgeble.ai>
---
Changes for v3, v2:
- none
drivers/pinctrl/pinctrl-rockchip.c | 333 ++++++++++++++++++++++++++++-
drivers/pinctrl/pinctrl-rockchip.h | 1 +
2 files changed, 327 insertions(+), 7 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index 32e41395fc76..a91061f9c2ac 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -57,6 +57,7 @@
#define IOMUX_UNROUTED BIT(3)
#define IOMUX_WIDTH_3BIT BIT(4)
#define IOMUX_WIDTH_2BIT BIT(5)
+#define IOMUX_L_SOURCE_PMU BIT(6)
#define PIN_BANK(id, pins, label) \
{ \
@@ -147,6 +148,21 @@
.pull_type[3] = pull3, \
}
+#define PIN_BANK_IOMUX_FLAGS_OFFSET(id, pins, label, iom0, iom1, iom2, \
+ iom3, offset0, offset1, offset2, \
+ offset3) \
+ { \
+ .bank_num = id, \
+ .nr_pins = pins, \
+ .name = label, \
+ .iomux = { \
+ { .type = iom0, .offset = offset0 }, \
+ { .type = iom1, .offset = offset1 }, \
+ { .type = iom2, .offset = offset2 }, \
+ { .type = iom3, .offset = offset3 }, \
+ }, \
+ }
+
#define PIN_BANK_IOMUX_DRV_FLAGS_OFFSET(id, pins, label, iom0, iom1, \
iom2, iom3, drv0, drv1, drv2, \
drv3, offset0, offset1, \
@@ -443,6 +459,37 @@ static struct rockchip_mux_recalced_data rv1108_mux_recalced_data[] = {
},
};
+static struct rockchip_mux_recalced_data rv1126_mux_recalced_data[] = {
+ {
+ .num = 0,
+ .pin = 20,
+ .reg = 0x10000,
+ .bit = 0,
+ .mask = 0xf
+ },
+ {
+ .num = 0,
+ .pin = 21,
+ .reg = 0x10000,
+ .bit = 4,
+ .mask = 0xf
+ },
+ {
+ .num = 0,
+ .pin = 22,
+ .reg = 0x10000,
+ .bit = 8,
+ .mask = 0xf
+ },
+ {
+ .num = 0,
+ .pin = 23,
+ .reg = 0x10000,
+ .bit = 12,
+ .mask = 0xf
+ },
+};
+
static struct rockchip_mux_recalced_data rk3128_mux_recalced_data[] = {
{
.num = 2,
@@ -642,6 +689,103 @@ static struct rockchip_mux_route_data px30_mux_route_data[] = {
RK_MUXROUTE_SAME(1, RK_PB7, 2, 0x184, BIT(16 + 9) | BIT(9)), /* uart3-rxm1 */
};
+static struct rockchip_mux_route_data rv1126_mux_route_data[] = {
+ RK_MUXROUTE_GRF(3, RK_PD2, 1, 0x10260, WRITE_MASK_VAL(0, 0, 0)), /* I2S0_MCLK_M0 */
+ RK_MUXROUTE_GRF(3, RK_PB0, 3, 0x10260, WRITE_MASK_VAL(0, 0, 1)), /* I2S0_MCLK_M1 */
+
+ RK_MUXROUTE_GRF(0, RK_PD4, 4, 0x10260, WRITE_MASK_VAL(3, 2, 0)), /* I2S1_MCLK_M0 */
+ RK_MUXROUTE_GRF(1, RK_PD5, 2, 0x10260, WRITE_MASK_VAL(3, 2, 1)), /* I2S1_MCLK_M1 */
+ RK_MUXROUTE_GRF(2, RK_PC7, 6, 0x10260, WRITE_MASK_VAL(3, 2, 2)), /* I2S1_MCLK_M2 */
+
+ RK_MUXROUTE_GRF(1, RK_PD0, 1, 0x10260, WRITE_MASK_VAL(4, 4, 0)), /* I2S2_MCLK_M0 */
+ RK_MUXROUTE_GRF(2, RK_PB3, 2, 0x10260, WRITE_MASK_VAL(4, 4, 1)), /* I2S2_MCLK_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PD4, 2, 0x10260, WRITE_MASK_VAL(12, 12, 0)), /* PDM_CLK0_M0 */
+ RK_MUXROUTE_GRF(3, RK_PC0, 3, 0x10260, WRITE_MASK_VAL(12, 12, 1)), /* PDM_CLK0_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PC6, 1, 0x10264, WRITE_MASK_VAL(0, 0, 0)), /* CIF_CLKOUT_M0 */
+ RK_MUXROUTE_GRF(2, RK_PD1, 3, 0x10264, WRITE_MASK_VAL(0, 0, 1)), /* CIF_CLKOUT_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA4, 5, 0x10264, WRITE_MASK_VAL(5, 4, 0)), /* I2C3_SCL_M0 */
+ RK_MUXROUTE_GRF(2, RK_PD4, 7, 0x10264, WRITE_MASK_VAL(5, 4, 1)), /* I2C3_SCL_M1 */
+ RK_MUXROUTE_GRF(1, RK_PD6, 3, 0x10264, WRITE_MASK_VAL(5, 4, 2)), /* I2C3_SCL_M2 */
+
+ RK_MUXROUTE_GRF(3, RK_PA0, 7, 0x10264, WRITE_MASK_VAL(6, 6, 0)), /* I2C4_SCL_M0 */
+ RK_MUXROUTE_GRF(4, RK_PA0, 4, 0x10264, WRITE_MASK_VAL(6, 6, 1)), /* I2C4_SCL_M1 */
+
+ RK_MUXROUTE_GRF(2, RK_PA5, 7, 0x10264, WRITE_MASK_VAL(9, 8, 0)), /* I2C5_SCL_M0 */
+ RK_MUXROUTE_GRF(3, RK_PB0, 5, 0x10264, WRITE_MASK_VAL(9, 8, 1)), /* I2C5_SCL_M1 */
+ RK_MUXROUTE_GRF(1, RK_PD0, 4, 0x10264, WRITE_MASK_VAL(9, 8, 2)), /* I2C5_SCL_M2 */
+
+ RK_MUXROUTE_GRF(3, RK_PC0, 5, 0x10264, WRITE_MASK_VAL(11, 10, 0)), /* SPI1_CLK_M0 */
+ RK_MUXROUTE_GRF(1, RK_PC6, 3, 0x10264, WRITE_MASK_VAL(11, 10, 1)), /* SPI1_CLK_M1 */
+ RK_MUXROUTE_GRF(2, RK_PD5, 6, 0x10264, WRITE_MASK_VAL(11, 10, 2)), /* SPI1_CLK_M2 */
+
+ RK_MUXROUTE_GRF(3, RK_PC0, 2, 0x10264, WRITE_MASK_VAL(12, 12, 0)), /* RGMII_CLK_M0 */
+ RK_MUXROUTE_GRF(2, RK_PB7, 2, 0x10264, WRITE_MASK_VAL(12, 12, 1)), /* RGMII_CLK_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA1, 3, 0x10264, WRITE_MASK_VAL(13, 13, 0)), /* CAN_TXD_M0 */
+ RK_MUXROUTE_GRF(3, RK_PA7, 5, 0x10264, WRITE_MASK_VAL(13, 13, 1)), /* CAN_TXD_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA4, 6, 0x10268, WRITE_MASK_VAL(0, 0, 0)), /* PWM8_M0 */
+ RK_MUXROUTE_GRF(2, RK_PD7, 5, 0x10268, WRITE_MASK_VAL(0, 0, 1)), /* PWM8_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA5, 6, 0x10268, WRITE_MASK_VAL(2, 2, 0)), /* PWM9_M0 */
+ RK_MUXROUTE_GRF(2, RK_PD6, 5, 0x10268, WRITE_MASK_VAL(2, 2, 1)), /* PWM9_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA6, 6, 0x10268, WRITE_MASK_VAL(4, 4, 0)), /* PWM10_M0 */
+ RK_MUXROUTE_GRF(2, RK_PD5, 5, 0x10268, WRITE_MASK_VAL(4, 4, 1)), /* PWM10_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PA7, 6, 0x10268, WRITE_MASK_VAL(6, 6, 0)), /* PWM11_IR_M0 */
+ RK_MUXROUTE_GRF(3, RK_PA1, 5, 0x10268, WRITE_MASK_VAL(6, 6, 1)), /* PWM11_IR_M1 */
+
+ RK_MUXROUTE_GRF(1, RK_PA5, 3, 0x10268, WRITE_MASK_VAL(8, 8, 0)), /* UART2_TX_M0 */
+ RK_MUXROUTE_GRF(3, RK_PA2, 1, 0x10268, WRITE_MASK_VAL(8, 8, 1)), /* UART2_TX_M1 */
+
+ RK_MUXROUTE_GRF(3, RK_PC6, 3, 0x10268, WRITE_MASK_VAL(11, 10, 0)), /* UART3_TX_M0 */
+ RK_MUXROUTE_GRF(1, RK_PA7, 2, 0x10268, WRITE_MASK_VAL(11, 10, 1)), /* UART3_TX_M1 */
+ RK_MUXROUTE_GRF(3, RK_PA0, 4, 0x10268, WRITE_MASK_VAL(11, 10, 2)), /* UART3_TX_M2 */
+
+ RK_MUXROUTE_GRF(3, RK_PA4, 4, 0x10268, WRITE_MASK_VAL(13, 12, 0)), /* UART4_TX_M0 */
+ RK_MUXROUTE_GRF(2, RK_PA6, 4, 0x10268, WRITE_MASK_VAL(13, 12, 1)), /* UART4_TX_M1 */
+ RK_MUXROUTE_GRF(1, RK_PD5, 3, 0x10268, WRITE_MASK_VAL(13, 12, 2)), /* UART4_TX_M2 */
+
+ RK_MUXROUTE_GRF(3, RK_PA6, 4, 0x10268, WRITE_MASK_VAL(15, 14, 0)), /* UART5_TX_M0 */
+ RK_MUXROUTE_GRF(2, RK_PB0, 4, 0x10268, WRITE_MASK_VAL(15, 14, 1)), /* UART5_TX_M1 */
+ RK_MUXROUTE_GRF(2, RK_PA0, 3, 0x10268, WRITE_MASK_VAL(15, 14, 2)), /* UART5_TX_M2 */
+
+ RK_MUXROUTE_PMU(0, RK_PB6, 3, 0x0114, WRITE_MASK_VAL(0, 0, 0)), /* PWM0_M0 */
+ RK_MUXROUTE_PMU(2, RK_PB3, 5, 0x0114, WRITE_MASK_VAL(0, 0, 1)), /* PWM0_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PB7, 3, 0x0114, WRITE_MASK_VAL(2, 2, 0)), /* PWM1_M0 */
+ RK_MUXROUTE_PMU(2, RK_PB2, 5, 0x0114, WRITE_MASK_VAL(2, 2, 1)), /* PWM1_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PC0, 3, 0x0114, WRITE_MASK_VAL(4, 4, 0)), /* PWM2_M0 */
+ RK_MUXROUTE_PMU(2, RK_PB1, 5, 0x0114, WRITE_MASK_VAL(4, 4, 1)), /* PWM2_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PC1, 3, 0x0114, WRITE_MASK_VAL(6, 6, 0)), /* PWM3_IR_M0 */
+ RK_MUXROUTE_PMU(2, RK_PB0, 5, 0x0114, WRITE_MASK_VAL(6, 6, 1)), /* PWM3_IR_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PC2, 3, 0x0114, WRITE_MASK_VAL(8, 8, 0)), /* PWM4_M0 */
+ RK_MUXROUTE_PMU(2, RK_PA7, 5, 0x0114, WRITE_MASK_VAL(8, 8, 1)), /* PWM4_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PC3, 3, 0x0114, WRITE_MASK_VAL(10, 10, 0)), /* PWM5_M0 */
+ RK_MUXROUTE_PMU(2, RK_PA6, 5, 0x0114, WRITE_MASK_VAL(10, 10, 1)), /* PWM5_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PB2, 3, 0x0114, WRITE_MASK_VAL(12, 12, 0)), /* PWM6_M0 */
+ RK_MUXROUTE_PMU(2, RK_PD4, 5, 0x0114, WRITE_MASK_VAL(12, 12, 1)), /* PWM6_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PB1, 3, 0x0114, WRITE_MASK_VAL(14, 14, 0)), /* PWM7_IR_M0 */
+ RK_MUXROUTE_PMU(3, RK_PA0, 5, 0x0114, WRITE_MASK_VAL(14, 14, 1)), /* PWM7_IR_M1 */
+
+ RK_MUXROUTE_PMU(0, RK_PB0, 1, 0x0118, WRITE_MASK_VAL(1, 0, 0)), /* SPI0_CLK_M0 */
+ RK_MUXROUTE_PMU(2, RK_PA1, 1, 0x0118, WRITE_MASK_VAL(1, 0, 1)), /* SPI0_CLK_M1 */
+ RK_MUXROUTE_PMU(2, RK_PB2, 6, 0x0118, WRITE_MASK_VAL(1, 0, 2)), /* SPI0_CLK_M2 */
+
+ RK_MUXROUTE_PMU(0, RK_PB6, 2, 0x0118, WRITE_MASK_VAL(2, 2, 0)), /* UART1_TX_M0 */
+ RK_MUXROUTE_PMU(1, RK_PD0, 5, 0x0118, WRITE_MASK_VAL(2, 2, 1)), /* UART1_TX_M1 */
+};
+
static struct rockchip_mux_route_data rk3128_mux_route_data[] = {
RK_MUXROUTE_SAME(1, RK_PB2, 1, 0x144, BIT(16 + 3) | BIT(16 + 4)), /* spi-0 */
RK_MUXROUTE_SAME(1, RK_PD3, 3, 0x144, BIT(16 + 3) | BIT(16 + 4) | BIT(3)), /* spi-1 */
@@ -877,8 +1021,12 @@ static int rockchip_get_mux(struct rockchip_pin_bank *bank, int pin)
if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY)
return RK_FUNC_GPIO;
- regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
- ? info->regmap_pmu : info->regmap_base;
+ if (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
+ regmap = info->regmap_pmu;
+ else if (bank->iomux[iomux_num].type & IOMUX_L_SOURCE_PMU)
+ regmap = (pin % 8 < 4) ? info->regmap_pmu : info->regmap_base;
+ else
+ regmap = info->regmap_base;
/* get basic quadrupel of mux registers and the correct reg inside */
mux_type = bank->iomux[iomux_num].type;
@@ -987,8 +1135,12 @@ static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
dev_dbg(dev, "setting mux of GPIO%d-%d to %d\n", bank->bank_num, pin, mux);
- regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
- ? info->regmap_pmu : info->regmap_base;
+ if (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
+ regmap = info->regmap_pmu;
+ else if (bank->iomux[iomux_num].type & IOMUX_L_SOURCE_PMU)
+ regmap = (pin % 8 < 4) ? info->regmap_pmu : info->regmap_base;
+ else
+ regmap = info->regmap_base;
/* get basic quadrupel of mux registers and the correct reg inside */
mux_type = bank->iomux[iomux_num].type;
@@ -1268,6 +1420,119 @@ static int rv1108_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
return 0;
}
+#define RV1126_PULL_PMU_OFFSET 0x40
+#define RV1126_PULL_GRF_GPIO1A0_OFFSET 0x10108
+#define RV1126_PULL_PINS_PER_REG 8
+#define RV1126_PULL_BITS_PER_PIN 2
+#define RV1126_PULL_BANK_STRIDE 16
+#define RV1126_GPIO_C4_D7(p) (p >= 20 && p <= 31) /* GPIO0_C4 ~ GPIO0_D7 */
+
+static int rv1126_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ /* The first 24 pins of the first bank are located in PMU */
+ if (bank->bank_num == 0) {
+ if (RV1126_GPIO_C4_D7(pin_num)) {
+ *regmap = info->regmap_base;
+ *reg = RV1126_PULL_GRF_GPIO1A0_OFFSET;
+ *reg -= (((31 - pin_num) / RV1126_PULL_PINS_PER_REG + 1) * 4);
+ *bit = pin_num % RV1126_PULL_PINS_PER_REG;
+ *bit *= RV1126_PULL_BITS_PER_PIN;
+ return 0;
+ }
+ *regmap = info->regmap_pmu;
+ *reg = RV1126_PULL_PMU_OFFSET;
+ } else {
+ *reg = RV1126_PULL_GRF_GPIO1A0_OFFSET;
+ *regmap = info->regmap_base;
+ *reg += (bank->bank_num - 1) * RV1126_PULL_BANK_STRIDE;
+ }
+
+ *reg += ((pin_num / RV1126_PULL_PINS_PER_REG) * 4);
+ *bit = (pin_num % RV1126_PULL_PINS_PER_REG);
+ *bit *= RV1126_PULL_BITS_PER_PIN;
+
+ return 0;
+}
+
+#define RV1126_DRV_PMU_OFFSET 0x20
+#define RV1126_DRV_GRF_GPIO1A0_OFFSET 0x10090
+#define RV1126_DRV_BITS_PER_PIN 4
+#define RV1126_DRV_PINS_PER_REG 4
+#define RV1126_DRV_BANK_STRIDE 32
+
+static int rv1126_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num, struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+
+ /* The first 24 pins of the first bank are located in PMU */
+ if (bank->bank_num == 0) {
+ if (RV1126_GPIO_C4_D7(pin_num)) {
+ *regmap = info->regmap_base;
+ *reg = RV1126_DRV_GRF_GPIO1A0_OFFSET;
+ *reg -= (((31 - pin_num) / RV1126_DRV_PINS_PER_REG + 1) * 4);
+ *reg -= 0x4;
+ *bit = pin_num % RV1126_DRV_PINS_PER_REG;
+ *bit *= RV1126_DRV_BITS_PER_PIN;
+ return 0;
+ }
+ *regmap = info->regmap_pmu;
+ *reg = RV1126_DRV_PMU_OFFSET;
+ } else {
+ *regmap = info->regmap_base;
+ *reg = RV1126_DRV_GRF_GPIO1A0_OFFSET;
+ *reg += (bank->bank_num - 1) * RV1126_DRV_BANK_STRIDE;
+ }
+
+ *reg += ((pin_num / RV1126_DRV_PINS_PER_REG) * 4);
+ *bit = pin_num % RV1126_DRV_PINS_PER_REG;
+ *bit *= RV1126_DRV_BITS_PER_PIN;
+
+ return 0;
+}
+
+#define RV1126_SCHMITT_PMU_OFFSET 0x60
+#define RV1126_SCHMITT_GRF_GPIO1A0_OFFSET 0x10188
+#define RV1126_SCHMITT_BANK_STRIDE 16
+#define RV1126_SCHMITT_PINS_PER_GRF_REG 8
+#define RV1126_SCHMITT_PINS_PER_PMU_REG 8
+
+static int rv1126_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
+ int pin_num,
+ struct regmap **regmap,
+ int *reg, u8 *bit)
+{
+ struct rockchip_pinctrl *info = bank->drvdata;
+ int pins_per_reg;
+
+ if (bank->bank_num == 0) {
+ if (RV1126_GPIO_C4_D7(pin_num)) {
+ *regmap = info->regmap_base;
+ *reg = RV1126_SCHMITT_GRF_GPIO1A0_OFFSET;
+ *reg -= (((31 - pin_num) / RV1126_SCHMITT_PINS_PER_GRF_REG + 1) * 4);
+ *bit = pin_num % RV1126_SCHMITT_PINS_PER_GRF_REG;
+ return 0;
+ }
+ *regmap = info->regmap_pmu;
+ *reg = RV1126_SCHMITT_PMU_OFFSET;
+ pins_per_reg = RV1126_SCHMITT_PINS_PER_PMU_REG;
+ } else {
+ *regmap = info->regmap_base;
+ *reg = RV1126_SCHMITT_GRF_GPIO1A0_OFFSET;
+ pins_per_reg = RV1126_SCHMITT_PINS_PER_GRF_REG;
+ *reg += (bank->bank_num - 1) * RV1126_SCHMITT_BANK_STRIDE;
+ }
+ *reg += ((pin_num / pins_per_reg) * 4);
+ *bit = pin_num % pins_per_reg;
+
+ return 0;
+}
+
#define RK3308_SCHMITT_PINS_PER_REG 8
#define RK3308_SCHMITT_BANK_STRIDE 16
#define RK3308_SCHMITT_GRF_OFFSET 0x1a0
@@ -1998,6 +2263,12 @@ static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank,
goto config;
}
+ if (ctrl->type == RV1126) {
+ rmask_bits = RV1126_DRV_BITS_PER_PIN;
+ ret = strength;
+ goto config;
+ }
+
ret = -EINVAL;
for (i = 0; i < ARRAY_SIZE(rockchip_perpin_drv_list[drv_type]); i++) {
if (rockchip_perpin_drv_list[drv_type][i] == strength) {
@@ -2168,6 +2439,7 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
break;
case PX30:
case RV1108:
+ case RV1126:
case RK3188:
case RK3288:
case RK3308:
@@ -2416,6 +2688,7 @@ static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl,
return pull ? false : true;
case PX30:
case RV1108:
+ case RV1126:
case RK3188:
case RK3288:
case RK3308:
@@ -2889,12 +3162,14 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
/* preset iomux offset value, set new start value */
if (iom->offset >= 0) {
- if (iom->type & IOMUX_SOURCE_PMU)
+ if ((iom->type & IOMUX_SOURCE_PMU) ||
+ (iom->type & IOMUX_L_SOURCE_PMU))
pmu_offs = iom->offset;
else
grf_offs = iom->offset;
} else { /* set current iomux offset */
- iom->offset = (iom->type & IOMUX_SOURCE_PMU) ?
+ iom->offset = ((iom->type & IOMUX_SOURCE_PMU) ||
+ (iom->type & IOMUX_L_SOURCE_PMU)) ?
pmu_offs : grf_offs;
}
@@ -2919,7 +3194,7 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(
inc = (iom->type & (IOMUX_WIDTH_4BIT |
IOMUX_WIDTH_3BIT |
IOMUX_WIDTH_2BIT)) ? 8 : 4;
- if (iom->type & IOMUX_SOURCE_PMU)
+ if ((iom->type & IOMUX_SOURCE_PMU) || (iom->type & IOMUX_L_SOURCE_PMU))
pmu_offs += inc;
else
grf_offs += inc;
@@ -3178,6 +3453,48 @@ static struct rockchip_pin_ctrl rv1108_pin_ctrl = {
.schmitt_calc_reg = rv1108_calc_schmitt_reg_and_bit,
};
+static struct rockchip_pin_bank rv1126_pin_banks[] = {
+ PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0",
+ IOMUX_WIDTH_4BIT | IOMUX_SOURCE_PMU,
+ IOMUX_WIDTH_4BIT | IOMUX_SOURCE_PMU,
+ IOMUX_WIDTH_4BIT | IOMUX_L_SOURCE_PMU,
+ IOMUX_WIDTH_4BIT),
+ PIN_BANK_IOMUX_FLAGS_OFFSET(1, 32, "gpio1",
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ 0x10010, 0x10018, 0x10020, 0x10028),
+ PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2",
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT),
+ PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3",
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT,
+ IOMUX_WIDTH_4BIT),
+ PIN_BANK_IOMUX_FLAGS(4, 2, "gpio4",
+ IOMUX_WIDTH_4BIT, 0, 0, 0),
+};
+
+static struct rockchip_pin_ctrl rv1126_pin_ctrl = {
+ .pin_banks = rv1126_pin_banks,
+ .nr_banks = ARRAY_SIZE(rv1126_pin_banks),
+ .label = "RV1126-GPIO",
+ .type = RV1126,
+ .grf_mux_offset = 0x10004, /* mux offset from GPIO0_D0 */
+ .pmu_mux_offset = 0x0,
+ .iomux_routes = rv1126_mux_route_data,
+ .niomux_routes = ARRAY_SIZE(rv1126_mux_route_data),
+ .iomux_recalced = rv1126_mux_recalced_data,
+ .niomux_recalced = ARRAY_SIZE(rv1126_mux_recalced_data),
+ .pull_calc_reg = rv1126_calc_pull_reg_and_bit,
+ .drv_calc_reg = rv1126_calc_drv_reg_and_bit,
+ .schmitt_calc_reg = rv1126_calc_schmitt_reg_and_bit,
+};
+
static struct rockchip_pin_bank rk2928_pin_banks[] = {
PIN_BANK(0, 32, "gpio0"),
PIN_BANK(1, 32, "gpio1"),
@@ -3568,6 +3885,8 @@ static const struct of_device_id rockchip_pinctrl_dt_match[] = {
.data = &px30_pin_ctrl },
{ .compatible = "rockchip,rv1108-pinctrl",
.data = &rv1108_pin_ctrl },
+ { .compatible = "rockchip,rv1126-pinctrl",
+ .data = &rv1126_pin_ctrl },
{ .compatible = "rockchip,rk2928-pinctrl",
.data = &rk2928_pin_ctrl },
{ .compatible = "rockchip,rk3036-pinctrl",
diff --git a/drivers/pinctrl/pinctrl-rockchip.h b/drivers/pinctrl/pinctrl-rockchip.h
index ec46f8815ac9..4759f336941e 100644
--- a/drivers/pinctrl/pinctrl-rockchip.h
+++ b/drivers/pinctrl/pinctrl-rockchip.h
@@ -186,6 +186,7 @@
enum rockchip_pinctrl_type {
PX30,
RV1108,
+ RV1126,
RK2928,
RK3066B,
RK3128,
--
2.25.1
More information about the linux-arm-kernel
mailing list