[PATCH] ARM: dts: ste: ux500: align SPI node name with dtschema

[Krzysztof Kozlowski]

The node names should be generic and DT schema expects certain pattern.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
---
 arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts | 2 +-
 arch/arm/boot/dts/ste-ux500-samsung-codina.dts     | 2 +-
 arch/arm/boot/dts/ste-ux500-samsung-gavini.dts     | 2 +-
 arch/arm/boot/dts/ste-ux500-samsung-janice.dts     | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts b/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts
index d6940e0afa86..17dff403f77a 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts
@@ -239,7 +239,7 @@ magnetometer at c {
 		};
 	};
 
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-codina.dts b/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
index 5f41256d7f4b..9db490cc395b 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
@@ -325,7 +325,7 @@ nfc at 2b {
 		};
 	};
 
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
index 806da3fc33cd..79d43fc68cd8 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
@@ -269,7 +269,7 @@ magnetometer at 2e {
 	/*
 	 * TODO: See if we can use the PL023 for this instead.
 	 */
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220, pin SCL */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
index ed5c79c3d04b..b34bd19ad815 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
@@ -263,7 +263,7 @@ magnetometer at 2e {
 	 * this derivative is 3wire support, so it cannot be used to drive
 	 * this panel interface. We have to use GPIO bit-banging instead.
 	 */
-	spi-gpio-0 {
+	spi {
 		compatible = "spi-gpio";
 		/* Clock on GPIO220 */
 		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
-- 
2.34.1