[PATCH RESEND 6/6] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju at ti.com>

J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same

Cc: Vignesh Raghavendra <vigneshr at ti.com>
Cc: Nishanth Menon <nm at ti.com>
Acked-by: Matt Ranostay <mranostay at ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 34 +++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 42 +++++++++++++++++++
 2 files changed, 76 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index aa75dc541842..cb99a97af426 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
 			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
 		>;
 	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+			J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+			J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+			J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+			J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+			J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+			J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+		>;
+	};
 };
 
 &main_gpio2 {
@@ -394,6 +408,26 @@ &usb0 {
 	maximum-speed = "high-speed";
 };
 
+&ospi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash at 0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mcu_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_mcan0_pins_default>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 76f0ceacb6d4..a05c17dd69b6 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@ transceiver0: can-phy0 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+			J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+			J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+			J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -78,6 +100,26 @@ &main_mcan16 {
 	phys = <&transceiver0>;
 };
 
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mailbox0_cluster0 {
 	status = "disabled";
 };
-- 
2.36.1