[PATCH v3 4/4] ARM: dts: stm32: add support for Protonic PRTT1x boards

Marc Kleine-Budde mkl at pengutronix.de
Mon Apr 25 06:49:41 PDT 2022 

On 25.04.2022 15:28:44, Oleksij Rempel wrote:
> This boards are based on STM32MP151AAD3 and use 10BaseT1L for communication.
> 
> - PRTT1C - 10BaseT1L switch
> - PRTT1S - 10BaseT1L CO2 sensor board
> - PRTT1A - 10BaseT1L multi functional controller
> 
> Signed-off-by: Oleksij Rempel <o.rempel at pengutronix.de>
> ---
>  arch/arm/boot/dts/Makefile                |   3 +
>  arch/arm/boot/dts/stm32mp151a-prtt1a.dts  |  52 ++++
>  arch/arm/boot/dts/stm32mp151a-prtt1c.dts  | 304 ++++++++++++++++++++++
>  arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi | 229 ++++++++++++++++
>  arch/arm/boot/dts/stm32mp151a-prtt1s.dts  |  63 +++++
>  5 files changed, 651 insertions(+)
>  create mode 100644 arch/arm/boot/dts/stm32mp151a-prtt1a.dts
>  create mode 100644 arch/arm/boot/dts/stm32mp151a-prtt1c.dts
>  create mode 100644 arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
>  create mode 100644 arch/arm/boot/dts/stm32mp151a-prtt1s.dts

[...]

> diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
> new file mode 100644
> index 000000000000..0d542c8ff2c7
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
> @@ -0,0 +1,304 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) Protonic Holland
> + * Author: David Jander <david at protonic.nl>
> + */
> +/dts-v1/;
> +
> +#include "stm32mp151a-prtt1l.dtsi"
> +
> +/ {
> +	model = "Protonic PRTT1C";
> +	compatible = "prt,prtt1c", "st,stm32mp151";
> +
> +	clock_ksz9031: clock-ksz9031 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <25000000>;
> +	};
> +
> +	clock_sja1105: clock-sja1105 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <25000000>;
> +	};
> +
> +	mdio0: mdio {
> +		compatible = "virtual,mdio-gpio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
> +			 &gpioa 2 GPIO_ACTIVE_HIGH>;
> +
> +	};
> +
> +	wifi_pwrseq: wifi-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&ethernet0 {
> +	fixed-link {
> +		speed = <100>;
> +		full-duplex;
> +	};
> +};
> +
> +&gpioa {
> +	gpio-line-names =
> +		"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
> +		"", "", "", "", "", "", "", "SPI1_nSS";
> +};
> +
> +&gpiod {
> +	gpio-line-names =
> +		"", "", "", "", "", "", "", "",
> +		"WFM_RESET", "", "", "", "", "", "", "";
> +};
> +
> +&gpioe {
> +	gpio-line-names =
> +		"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
> +		"", "", "", "", "WFM_nIRQ", "", "", "";
> +};
> +
> +&gpiog {
> +	gpio-line-names =
> +		"", "", "", "", "", "", "", "PHY3_nINT",
> +		"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
> +		"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
> +};
> +
> +&mdio0 {
> +	/* All this DP83TD510E PHYs can't be probed before switch at 0 is
> +	 * probed so we need to use compatible with PHYid
> +	 */
> +	/* TI DP83TD510E */
> +	t1l0_phy: ethernet-phy at 6 {
> +		compatible = "ethernet-phy-id2000.0181";
> +		reg = <6>;
> +		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10>;
> +		reset-deassert-us = <35>;
> +	};
> +
> +	/* TI DP83TD510E */
> +	t1l1_phy: ethernet-phy at 7 {
> +		compatible = "ethernet-phy-id2000.0181";
> +		reg = <7>;
> +		interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10>;
> +		reset-deassert-us = <35>;
> +	};
> +
> +	/* TI DP83TD510E */
> +	t1l2_phy: ethernet-phy at 10 {
> +		compatible = "ethernet-phy-id2000.0181";
> +		reg = <10>;
> +		interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10>;
> +		reset-deassert-us = <35>;
> +	};
> +
> +	/* Micrel KSZ9031 */
> +	rj45_phy: ethernet-phy at 2 {
> +		reg = <2>;
> +		interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10000>;
> +		reset-deassert-us = <1000>;
> +
> +		clocks = <&clock_ksz9031>;
> +	};
> +};
> +
> +&qspi {
> +	status = "disabled";
> +};
> +
> +&sdmmc2 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	no-1-8-v;
> +	st,neg-edge;
> +	bus-width = <8>;
> +	vmmc-supply = <&reg_3v3>;
> +	vqmmc-supply = <&reg_3v3>;
> +	status = "okay";
> +};
> +
> +&sdmmc2_b4_od_pins_a {
> +	pins1 {
> +		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
> +			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
> +			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
> +			 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
> +	};
> +};
> +
> +&sdmmc2_b4_pins_a {
> +	pins1 {
> +		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
> +			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
> +			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
> +			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
> +			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
> +	};
> +};
> +
> +&sdmmc2_b4_sleep_pins_a {
> +	pins {
> +		pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
> +			 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
> +			 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
> +			 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
> +			 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
> +			 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
> +	};
> +};
> +
> +&sdmmc2_d47_pins_a {
> +	pins {
> +		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
> +			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
> +			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
> +			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
> +	};
> +};
> +
> +&sdmmc2_d47_sleep_pins_a {
> +	pins {
> +		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
> +			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
> +			 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
> +			 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
> +	};
> +};
> +
> +&sdmmc3 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc3_b4_pins_b>;
> +	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
> +	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
> +	non-removable;
> +	no-1-8-v;
> +	st,neg-edge;
> +	bus-width = <4>;
> +	vmmc-supply = <&reg_3v3>;
> +	vqmmc-supply = <&reg_3v3>;
> +        mmc-pwrseq = <&wifi_pwrseq>;

nitpick: use tabs here, too

Marc

-- 
Pengutronix e.K.                 | Marc Kleine-Budde           |
Embedded Linux                   | https://www.pengutronix.de  |
Vertretung West/Dortmund         | Phone: +49-231-2826-924     |
Amtsgericht Hildesheim, HRA 2686 | Fax:   +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20220425/20380006/attachment.sig>

More information about the linux-arm-kernel mailing list