[PATCH resend v8 1/5] drm/bridge: nwl-dsi: Set PHY mode in nwl_dsi_mode_set()

[Robert Foss]

On Tue, 19 Apr 2022 at 03:07, Liu Ying <victor.liu at nxp.com> wrote:
>
> The Northwest Logic MIPI DSI host controller embedded in i.MX8qxp
> works with a Mixel MIPI DPHY + LVDS PHY combo to support either
> a MIPI DSI display or a LVDS display.  So, this patch calls
> phy_set_mode() from nwl_dsi_mode_set() to set PHY mode to MIPI DPHY
> explicitly.
>
> Cc: Guido Günther <agx at sigxcpu.org>
> Cc: Robert Chiras <robert.chiras at nxp.com>
> Cc: Martin Kepplinger <martin.kepplinger at puri.sm>
> Cc: Andrzej Hajda <andrzej.hajda at intel.com>
> Cc: Neil Armstrong <narmstrong at baylibre.com>
> Cc: Laurent Pinchart <Laurent.pinchart at ideasonboard.com>
> Cc: Jonas Karlman <jonas at kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec at gmail.com>
> Cc: David Airlie <airlied at linux.ie>
> Cc: Daniel Vetter <daniel at ffwll.ch>
> Cc: NXP Linux Team <linux-imx at nxp.com>
> Signed-off-by: Liu Ying <victor.liu at nxp.com>
> ---
> v7->v8:
> * Resend with Andrzej's and Jernej's mail addressed updated.
>
> v6->v7:
> * No change.
>
> v5->v6:
> * Rebase the series upon v5.17-rc1.
> * Set PHY mode in ->mode_set() instead of ->pre_enable() in the nwl-dsi
>   bridge driver due to the rebase.
> * Drop Guido's R-b tag due to the rebase.
>
> v4->v5:
> * No change.
>
> v3->v4:
> * No change.
>
> v2->v3:
> * No change.
>
> v1->v2:
> * Add Guido's R-b tag.
>
>  drivers/gpu/drm/bridge/nwl-dsi.c | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index d5945501a5ee..85bab7372af1 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -666,6 +666,12 @@ static int nwl_dsi_mode_set(struct nwl_dsi *dsi)
>                 return ret;
>         }
>
> +       ret = phy_set_mode(dsi->phy, PHY_MODE_MIPI_DPHY);
> +       if (ret < 0) {
> +               DRM_DEV_ERROR(dev, "Failed to set DSI phy mode: %d\n", ret);
> +               goto uninit_phy;
> +       }
> +
>         ret = phy_configure(dsi->phy, phy_cfg);
>         if (ret < 0) {
>                 DRM_DEV_ERROR(dev, "Failed to configure DSI phy: %d\n", ret);
> --
> 2.25.1
>

Acked-by: Robert Foss <robert.foss at linaro.org>