[PATCH v8 01/13] arm64: dts: freescale: Add the top level dtsi support for imx8dxl

[Krzysztof Kozlowski]

On 19/04/2022 13:35, Abel Vesa wrote:
> From: Jacky Bai <ping.bai at nxp.com>
> 
> The i.MX8DXL is a device targeting the automotive and industrial
> market segments. The flexibility of the architecture allows for
> use in a wide variety of general embedded applications. The chip
> is designed to achieve both high performance and low power consumption.
> The chip relies on the power efficient dual (2x) Cortex-A35 cluster.
> 
> Add the reserved memory node property for dsp reserved memory,
> the wakeup-irq property for SCU node, the rpmsg and the cm4 rproc
> support.
> 
> Signed-off-by: Jacky Bai <ping.bai at nxp.com>
> Signed-off-by: Abel Vesa <abel.vesa at nxp.com>


(...)

> +	thermal_zones: thermal-zones {
> +		cpu-thermal0 {

Same concerns as you DTS.

> +			polling-delay-passive = <250>;
> +			polling-delay = <2000>;
> +			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
> +
> +			trips {
> +				cpu_alert0: trip0 {
> +					temperature = <107000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpu_crit0: trip1 {
> +					temperature = <127000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu_alert0>;
> +					cooling-device =
> +					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +	};
> +
> +	clk_dummy: clock-dummy {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <0>;
> +		clock-output-names = "clk_dummy";
> +	};
> +
> +	xtal32k: clock-xtal32k {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		clock-output-names = "xtal_32KHz";
> +	};
> +
> +	xtal24m: clock-xtal24m {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <24000000>;
> +		clock-output-names = "xtal_24MHz";
> +	};
> +
> +	/* sorted in register address */
> +	#include "imx8-ss-adma.dtsi"
> +	#include "imx8-ss-conn.dtsi"
> +	#include "imx8-ss-ddr.dtsi"
> +	#include "imx8-ss-lsio.dtsi"
> +};
> +
> +#include "imx8dxl-ss-adma.dtsi"

There is no such file. Your changes are not bisectable.

> +#include "imx8dxl-ss-conn.dtsi"
> +#include "imx8dxl-ss-lsio.dtsi"
> +#include "imx8dxl-ss-ddr.dtsi"


Best regards,
Krzysztof