[PATCH] ARM: dts: BCM5301X: Add DT for Buffalo WZR-1166DHP2

[SHIMAMOTO Takayoshi]

Buffalo WZR-1166DHP2  wireless router with

 - BCM4708A0
 - 256MiB DDR2 SDRAM
 - 128MiB NAND flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 4x 10/100M ethernet switch

The hardware configuration is very similar to the WZR-1750DHP,
except for memory size and number of antennas.

Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360 at gmail.com>
---
 .../boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts | 189 ++++++++++++++++++
 1 file changed, 189 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts

diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 000000000000..22e54a0a202a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5 at gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360 at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP2 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		gpio-sck = <&chipcommon 7 0>;
+		gpio-mosi = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi at 0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		power0 {
+			label = "bcm53xx:red:power";
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		power1 {
+			label = "bcm53xx:white:power";
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		router0 {
+			label = "bcm53xx:blue:router";
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		router1 {
+			label = "bcm53xx:amber:router";
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		wireless0 {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless1 {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		sw_ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port at 0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port at 1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port at 2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port at 3 {
+			reg = <3>;
+			label = "lan4";
+		};
+
+		port at 4 {
+			reg = <4>;
+			label = "wan";
+		};
+
+		port at 5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+		};
+	};
+};
-- 
2.30.2