[PATCH v4 02/11] soc: imx: add i.MX8MP HSIO blk-ctrl

[Lucas Stach]

Am Donnerstag, dem 07.04.2022 um 01:43 +0200 schrieb Marek Vasut:
> On 4/6/22 17:33, Lucas Stach wrote:
> 
> [...]
> 
> > +static const struct imx8mp_blk_ctrl_data imx8mp_hsio_blk_ctl_dev_data = {
> > +	.max_reg = 0x24,
> 
> Doesn't the HSIO_BLK_CTL go up to 0x10c ?

Technically yes, but there is already a driver for the USB glue
(fsl,imx8mp-dwc3) that occupies the USB registers at and above 0x100.
 
> 
> > +	.power_on = imx8mp_hsio_blk_ctrl_power_on,
> > +	.power_off = imx8mp_hsio_blk_ctrl_power_off,
> > +	.power_notifier_fn = imx8mp_hsio_power_notifier,
> > +	.domains = imx8mp_hsio_domain_data,
> > +	.num_domains = ARRAY_SIZE(imx8mp_hsio_domain_data),
> > +};
> > +
> > +static int imx8mp_blk_ctrl_power_on(struct generic_pm_domain *genpd)
> > +{
> > +	struct imx8mp_blk_ctrl_domain *domain = to_imx8mp_blk_ctrl_domain(genpd);
> > +	const struct imx8mp_blk_ctrl_domain_data *data = domain->data;
> > +	struct imx8mp_blk_ctrl *bc = domain->bc;
> > +	int ret;
> > +
> > +	/* make sure bus domain is awake */
> > +	ret = pm_runtime_resume_and_get(bc->bus_power_dev);
> > +	if (ret < 0) {
> > +		dev_err(bc->dev, "failed to power up bus domain\n");
> > +		return ret;
> > +	}
> > +
> > +	/* enable upstream clocks */
> > +	ret = clk_bulk_prepare_enable(data->num_clks, domain->clks);;
> > +	if (ret) {
> > +		dev_err(bc->dev, "failed to enable clocks\n");
> > +		goto bus_put;
> > +	}
> > +
> > +	/* domain specific blk-ctrl manipulation */
> > +	bc->power_on(bc, domain);
> 
> Would it make sense to add error checking ?
> 
I don't expect those functions to do any more than a bit of blk-ctrl
MMIO register poking. If that fails you are in much more trouble than
what you can reasonably fix with some error checking.

Regards,
Lucas

> > +	/* power up upstream GPC domain */
> > +	ret = pm_runtime_resume_and_get(domain->power_dev);
> > +	if (ret < 0) {
> > +		dev_err(bc->dev, "failed to power up peripheral domain\n");
> > +		goto clk_disable;
> > +	}
> > +
> > +	clk_bulk_disable_unprepare(data->num_clks, domain->clks);
> > +
> > +	return 0;
> > +
> > +clk_disable:
> > +	clk_bulk_disable_unprepare(data->num_clks, domain->clks);
> > +bus_put:
> > +	pm_runtime_put(bc->bus_power_dev);
> > +
> > +	return ret;
> > +}
> 
> [...]