[PATCH v14 2/5] dt-bindings: pinctrl: mt8195: change pull up/down description

Rob Herring robh at kernel.org
Wed Sep 29 14:47:56 PDT 2021


On Fri, Sep 24, 2021 at 04:06:29PM +0800, Zhiyong Tao wrote:
> For supporting SI units in "bias-pull-down" & "bias-pull-up",
> change pull up/down description
> and add "mediatek,rsel_resistance_in_si_unit" description.
> 
> Signed-off-by: Zhiyong Tao <zhiyong.tao at mediatek.com>
> ---
>  .../bindings/pinctrl/pinctrl-mt8195.yaml      | 86 ++++++++++++++++++-
>  1 file changed, 84 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> index 2f12ec59eee5..5f642bef72af 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> @@ -49,6 +49,12 @@ properties:
>      description: The interrupt outputs to sysirq.
>      maxItems: 1
>  
> +  mediatek,rsel_resistance_in_si_unit:

s/_/-/

> +    type: boolean
> +    description: |
> +      Identifying i2c pins pull up/down type which is RSEL. It can support
> +      RSEL define or si unit value(ohm) to set different resistance.

Aren't the RSEL and ohms disjoint values? 0-207 for RSEL and >1000 for 
ohms. Why is this property even needed.

> +
>  #PIN CONFIGURATION NODES
>  patternProperties:
>    '-pins$':
> @@ -85,9 +91,85 @@ patternProperties:
>            2/4/6/8/10/12/14/16mA in mt8195.
>          enum: [0, 1, 2, 3, 4, 5, 6, 7]
>  
> -      bias-pull-down: true
> +      bias-pull-down:
> +        description: |
> +          For pull down type is normal, it don't need add RSEL & R1R0 define
> +          and resistance value.
> +          For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
> +          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> +          define in mt8195.
> +          For pull down type is RSEL, it can add RSEL define & resistance value(ohm)
> +          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> +          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +          define in mt8195. It can also support resistance value(ohm) "75000" & "5000" in mt8195.
> +          oneOf:

Because of the indentation, this is all just part of 'description'.

> +            - enum: [100, 101, 102, 103]
> +            - description: mt8195 pull down PUPD/R0/R1 type define value.

This entry is always true.

> +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]

Are these supposed to be hex?

> +            - description: mt8195 pull down RSEL type define value.

And so is this one. That makes 'oneOf' always false.

> +            - enum: [75000, 5000]
> +            - description: mt8195 pull down RSEL type si unit value(ohm).
> +
> +          An example of using RSEL define:
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-down = <MTK_PULL_SET_RSEL_001>;
> +            };
> +          };
> +          An example of using si unit resistance value(ohm):
> +          &pio {
> +            mediatek,rsel_resistance_in_si_unit;
> +          }
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-down = <75000>;
> +            };
> +          };
>  
> -      bias-pull-up: true
> +      bias-pull-up:
> +        description: |
> +          For pull up type is normal, it don't need add RSEL & R1R0 define
> +          and resistance value.
> +          For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
> +          set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> +          "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> +          define in mt8195.
> +          For pull up type is RSEL, it can add RSEL define & resistance value(ohm)
> +          to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> +          It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> +          & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> +          & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> +          define in mt8195. It can also support resistance value(ohm)
> +          "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8195.
> +          oneOf:
> +            - enum: [100, 101, 102, 103]
> +            - description: mt8195 pull up PUPD/R0/R1 type define value.
> +            - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> +            - description: mt8195 pull up RSEL type define value.
> +            - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
> +            - description: mt8195 pull up RSEL type si unit value(ohm).

Same issues here.

> +          An example of using RSEL define:
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> +            };
> +          };
> +          An example of using si unit resistance value(ohm):
> +          &pio {
> +            mediatek,rsel_resistance_in_si_unit;
> +          }
> +          pincontroller {
> +            i2c0_pin {
> +              pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> +              bias-pull-up = <1000>;
> +            };
> +          };
>  
>        bias-disable: true
>  
> -- 
> 2.25.1
> 
> 



More information about the linux-arm-kernel mailing list