[PATCH v3 0/9] add the imx8m pcie phy driver and imx8mm pcie support
Tim Harvey
tharvey at gateworks.com
Fri Oct 22 08:59:16 PDT 2021
On Thu, Oct 21, 2021 at 5:43 PM Richard Zhu <hongxing.zhu at nxp.com> wrote:
>
> > -----Original Message-----
> > From: Tim Harvey <tharvey at gateworks.com>
> > Sent: Friday, October 22, 2021 12:25 AM
> > To: Richard Zhu <hongxing.zhu at nxp.com>
> > Cc: Lucas Stach <l.stach at pengutronix.de>; Kishon Vijay Abraham I
> > <kishon at ti.com>; vkoul at kernel.org; Rob Herring <robh at kernel.org>;
> > galak at kernel.crashing.org; Shawn Guo <shawnguo at kernel.org>;
> > linux-phy at lists.infradead.org; Device Tree Mailing List
> > <devicetree at vger.kernel.org>; Linux ARM Mailing List
> > <linux-arm-kernel at lists.infradead.org>; open list
> > <linux-kernel at vger.kernel.org>; Sascha Hauer <kernel at pengutronix.de>;
> > dl-linux-imx <linux-imx at nxp.com>
> > Subject: Re: [PATCH v3 0/9] add the imx8m pcie phy driver and imx8mm pcie
> > support
> >
> > On Wed, Oct 20, 2021 at 8:32 PM Richard Zhu <hongxing.zhu at nxp.com>
> > wrote:
> > >
> > > <snipped...>
> > > >
> > > > Richard,
> > > >
> > > > What is this 'invalid resource' about? I see that with my downstream
> > > > IMX8MM PCIe driver as well and have been asked about it.
> > > >
> > > [Richard Zhu] Hi Tim:
> > > This complain is caused by the following codes in pcie-designware.c driver.
> > > I'm not sure that why there is only size assignment after the res valid check,
> > and do nothing if the res is invalid.
> > > It seems that it is an expected design logic refer to the later codes.
> > > if (!pci->atu_base) {
> > > struct resource *res =
> > >
> > platform_get_resource_byname(pdev, IORESOURCE_MEM, "atu");
> > > if (res)
> > > pci->atu_size = resource_size(res);
> > > pci->atu_base =
> > devm_ioremap_resource(dev, res);
> > > if (IS_ERR(pci->atu_base))
> > > pci->atu_base = pci->dbi_base +
> > DEFAULT_DBI_ATU_OFFSET;
> > > }
> > >
> > > Since the default offset is used on i.MX8MM, the "atu" is not specified in
> > i.MX8MM PCIe DT node, so there is no real res at all.
> > > Then, devm_ioremap_resource() would complain the invalid resource.
> >
> > I think you are saying a change should be made like this:
> > diff --git a/drivers/pci/controller/dwc/pcie-designware.c
> > b/drivers/pci/controller/dwc/pcie-designware.c
> > index a945f0c0e73d..3254f60d1713 100644
> > --- a/drivers/pci/controller/dwc/pcie-designware.c
> > +++ b/drivers/pci/controller/dwc/pcie-designware.c
> > @@ -671,10 +671,11 @@ void dw_pcie_iatu_detect(struct dw_pcie *pci)
> > if (!pci->atu_base) {
> > struct resource *res =
> >
> > platform_get_resource_byname(pdev,
> > IORESOURCE_MEM, "atu");
> > - if (res)
> > + if (res) {
> > pci->atu_size = resource_size(res);
> > - pci->atu_base = devm_ioremap_resource(dev,
> > res);
> > - if (IS_ERR(pci->atu_base))
> > + pci->atu_base =
> > devm_ioremap_resource(dev, res);
> > + }
> > + if (!pci->atu_base || IS_ERR(pci->atu_base))
> > pci->atu_base = pci->dbi_base +
> > DEFAULT_DBI_ATU_OFFSET;
> > }
> >
> > so that it looks like this:
> > if (!pci->atu_base) {
> > struct resource *res =
> >
> > platform_get_resource_byname(pdev,
> > IORESOURCE_MEM, "atu");
> > if (res) {
> > pci->atu_size = resource_size(res);
> > pci->atu_base =
> > devm_ioremap_resource(dev, res);
> > }
> > if (!pci->atu_base || IS_ERR(pci->atu_base))
> > pci->atu_base = pci->dbi_base +
> > DEFAULT_DBI_ATU_OFFSET;
> > }
> >
> > Right?
> [Richard Zhu] Yes, it is. The res shouldn't be remapped if it is invalid resource memory.
Ok, I will submit a patch for that.
>
> >
> > >
> > > > > [ 1.316305] imx6q-pcie 33800000.pcie: iATU unroll: enabled
> > > > > [ 1.321799] imx6q-pcie 33800000.pcie: Detected iATU regions: 4
> > > > outbound, 4 inbound
> > > > > [ 1.429803] imx6q-pcie 33800000.pcie: Link up
> > > > > [ 1.534497] imx6q-pcie 33800000.pcie: Link up
> > > > > [ 1.538870] imx6q-pcie 33800000.pcie: Link up, Gen2
> > > > > [ 1.550364] imx6q-pcie 33800000.pcie: Link up
> > > > > [ 1.550487] imx6q-pcie 33800000.pcie: PCI host bridge to bus
> > 0000:00
> > > > > [ 1.565545] pci_bus 0000:00: root bus resource [bus 00-ff]
> > > > > [ 1.573834] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
> > > > > [ 1.580055] pci_bus 0000:00: root bus resource [mem
> > > > 0x18000000-0x1fefffff]
> > > > > [ 1.586968] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400
> > > > > [ 1.592997] pci 0000:00:00.0: reg 0x10: [mem
> > 0x00000000-0x000fffff]
> > > > > [ 1.599282] pci 0000:00:00.0: reg 0x38: [mem
> > 0x00000000-0x0000ffff
> > > > pref]
> > > > > [ 1.606033] pci 0000:00:00.0: supports D1
> > > > > [ 1.610053] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
> > > > D3cold
> > > > > [ 1.618206] pci 0000:01:00.0: [15b7:5002] type 00 class 0x010802
> > > > > [ 1.624293] pci 0000:01:00.0: reg 0x10: [mem
> > 0x00000000-0x00003fff
> > > > 64bit]
> > > > > [ 1.631177] pci 0000:01:00.0: reg 0x20: [mem
> > 0x00000000-0x000000ff
> > > > 64bit]
> > > > > [ 1.638409] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth,
> > > > limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 31.504
> > > > Gb/s with
> > > > 8.0 GT/s PCIe x4 link)
> > > > > [ 1.664931] pci 0000:00:00.0: BAR 0: assigned [mem
> > > > 0x18000000-0x180fffff]
> > > > > [ 1.671745] pci 0000:00:00.0: BAR 14: assigned [mem
> > > > 0x18100000-0x181fffff]
> > > > > [ 1.678634] pci 0000:00:00.0: BAR 6: assigned [mem
> > > > 0x18200000-0x1820ffff pref]
> > > > > [ 1.685873] pci 0000:01:00.0: BAR 0: assigned [mem
> > > > 0x18100000-0x18103fff 64bit]
> > > > > [ 1.693222] pci 0000:01:00.0: BAR 4: assigned [mem
> > > > 0x18104000-0x181040ff 64bit]
> > > > > [ 1.700577] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
> > > > > [ 1.705814] pci 0000:00:00.0: bridge window [mem
> > > > 0x18100000-0x181fffff]
> > > > > [ 1.712972] pcieport 0000:00:00.0: PME: Signaling with IRQ 216
> > > > > "
> > > > > Regarding the log you pasted, it seems that the clock is not feed
> > > > > to PHY
> > > > properly.
> > > > >
> > > > > Anyway, let's waiting for the v4 series, then make a try. Thanks
> > > > > for your
> > > > great help to make the double tests.
> > > > >
> > > >
> > > > My boards do not use CLKREQ# so I do not have that defined in pinmux
> > > > and I found that if I add MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B
> > PCIe
> > > > works on my board but this isn't a solution just a work-around (I
> > > > have boards that use the only two possible pins for CLKREQ as other
> > features).
> > > >
> > > > Similarly you will find on the imx8mm-evk if you comment out the
> > > > CLKREQ (which isn't required) the imx8mmevk will end up hanging like my
> > boards:
> > > [Richard Zhu] Hi Tim:
> > > Regarding the SPEC, the CLKREQ# is mandatory required, and should be
> > configured as an open drain, active low signal.
> > > And this signal should be driven low by the PCIe M.2 device to request the
> > REF clock be available(active low).
> > > So, there is such kind of CLKREQ# pin definition on i.MX8MM EVK board.
> > >
> > > Anyway, I think the external OSC circuit should be always running if there is
> > no CLKREQ# on your HW board design.
> > >
> >
> > The way I understand it is CLKREQ# allows the host to disable the REFCLK
> > when not needed for power savings so it would seem optional to implement
> > that and if not implemented should be left unconnected on the card.
> >
> [Richard Zhu] No, not that way. Regarding the SPEC, this signal is mandatory required.
> Especially for the L1ss usages. This signal would be OD(open drain), bi-directional, and might be
> driven low/high by RC or EP automatically if L1ss modes are enabled.
> You can make reference to the "ECN_L1_PM_Substates_with_CLKREQ_31_May_2013_Rev10a", or
> the chapter 5.5 L1 PM Substates of "PCI Express Base Specification, Rev. 4.0 Version 1.0".
>
CLKREQ is only mandatory if you wish to support clock power
management. Many boards with a PCI host controller do not support
this.
> > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > index 5ce43daa0c8b..f0023b48f475 100644
> > > > --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > @@ -448,7 +448,9 @@
> > > >
> > > > pinctrl_pcie0: pcie0grp {
> > > > fsl,pins = <
> > > > +/*
> > > >
> > > > MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61
> > > > +*/
> > > >
> > MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21
> > > > 0x41
> > > > >;
> > > > };
> > > >
> > > > I have PCIe working with a driver that I ported from NXP's kernel
> > > > which differs from your driver in that the PCIe PHY is not
> > > > abstracted to its own driver so I think this has something to do
> > > > with the order in which the phy is reset or initialized? The configuration of
> > gpr14 bits looks correct to me.
> > > [Richard Zhu] The CLKREQ# PIN definition shouldn't be masked.
> > > In the NXP's local BSP kernel, I just force CLKREQ# low to level up the HW
> > compatibility.
> > > That's might the reason why the PCIe works on your HW board although the
> > CLKREQ# PIN is not defined.
> > > This method is a little rude and violate the SPEC, and not recommended
> > although it levels up the HW compatibility.
> > > So I drop this method in this series.
> > >
> >
> > Sorry, I don't understand what you are saying here. Is there a change you are
> > going to make to v4 that will make this work for the evk and my boards? What
> > is that change exactly?
> [Richard Zhu] No. What I said above is that the CLKREQ# is forced to be low in NXP
> local BSP kernel. I guess this might be the reason why your board works.
>
> BIT11 and BIT10 of IOMUXC_GPR14 can be used to force the CLKREQ# to be low.
> Set CLKREQ_OVERRIDE_EN(bit10) 1b1, then write one zero to CLKREQ_OVERRIDE(bit11).
>
Ok, that makes sense. Those bits are not explained well in the
IMX8MMRM. As my board's external REFCLK is always enabled that must
gate the clock internally to the host controller block.
I can confirm that asserting those GPR14 bits does resolve my issue:
#define IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_VAL BIT(11)
#define IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_EN BIT(10)
/*
* for boards that do not connect CLKREQ#,
* override CLKREQ# and drive it low internally
*/
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_VAL, 0);
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_EN, 1);
Should this be added as a 'fsl,clkreq-unsupported' flag that needs to
be set true to implement the above code?
Best regards,
Tim
More information about the linux-arm-kernel
mailing list