[PATCH] ARM: dts: spear13xx: Drop malformed 'interrupt-map' on PCI nodes

[Viresh Kumar]

On 21-10-21, 16:12, Rob Herring wrote:
> On Mon, Oct 4, 2021 at 1:14 AM Viresh Kumar <viresh.kumar at linaro.org> wrote:
> >
> > On 28-09-21, 14:21, Rob Herring wrote:
> > > The spear13xx PCI 'interrupt-map' property is not parse-able.
> > > '#interrupt-cells' is missing and there are 3 #address-cells. Based on the
> > > driver, the only supported interrupt is for MSI. Therefore, 'interrupt-map'
> > > is not needed.
> > >
> > > Cc: Viresh Kumar <vireshk at kernel.org>
> > > Cc: Shiraz Hashim <shiraz.linux.kernel at gmail.com>
> > > Cc: linux-arm-kernel at lists.infradead.org
> > > Signed-off-by: Rob Herring <robh at kernel.org>
> > > ---
> > >  arch/arm/boot/dts/spear1310.dtsi | 6 ------
> > >  arch/arm/boot/dts/spear1340.dtsi | 2 --
> > >  2 files changed, 8 deletions(-)
> > >
> > > diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi
> > > index c4b49baf9804..2f746a9428a7 100644
> > > --- a/arch/arm/boot/dts/spear1310.dtsi
> > > +++ b/arch/arm/boot/dts/spear1310.dtsi
> > > @@ -82,8 +82,6 @@ pcie0: pcie at b1000000 {
> > >                       reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
> > >                       reg-names = "dbi", "config";
> > >                       interrupts = <0 68 0x4>;
> > > -                     interrupt-map-mask = <0 0 0 0>;
> > > -                     interrupt-map = <0x0 0 &gic 0 68 0x4>;
> > >                       num-lanes = <1>;
> > >                       phys = <&miphy0 1>;
> > >                       phy-names = "pcie-phy";
> > > @@ -101,8 +99,6 @@ pcie1: pcie at b1800000 {
> > >                       reg = <0xb1800000 0x4000>, <0x90000000 0x20000>;
> > >                       reg-names = "dbi", "config";
> > >                       interrupts = <0 69 0x4>;
> > > -                     interrupt-map-mask = <0 0 0 0>;
> > > -                     interrupt-map = <0x0 0 &gic 0 69 0x4>;
> > >                       num-lanes = <1>;
> > >                       phys = <&miphy1 1>;
> > >                       phy-names = "pcie-phy";
> > > @@ -120,8 +116,6 @@ pcie2: pcie at b4000000 {
> > >                       reg = <0xb4000000 0x4000>, <0xc0000000 0x20000>;
> > >                       reg-names = "dbi", "config";
> > >                       interrupts = <0 70 0x4>;
> > > -                     interrupt-map-mask = <0 0 0 0>;
> > > -                     interrupt-map = <0x0 0 &gic 0 70 0x4>;
> > >                       num-lanes = <1>;
> > >                       phys = <&miphy2 1>;
> > >                       phy-names = "pcie-phy";
> > > diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi
> > > index 1a8f5e8b10e3..827e887afbda 100644
> > > --- a/arch/arm/boot/dts/spear1340.dtsi
> > > +++ b/arch/arm/boot/dts/spear1340.dtsi
> > > @@ -47,8 +47,6 @@ pcie0: pcie at b1000000 {
> > >                       reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
> > >                       reg-names = "dbi", "config";
> > >                       interrupts = <0 68 0x4>;
> > > -                     interrupt-map-mask = <0 0 0 0>;
> > > -                     interrupt-map = <0x0 0 &gic 0 68 0x4>;
> > >                       num-lanes = <1>;
> > >                       phys = <&miphy0 1>;
> > >                       phy-names = "pcie-phy";
> >
> > Acked-by: Viresh Kumar <viresh.kumar at linaro.org>
> 
> Are you going to apply this?

No, you or Arnd can directly apply it. I don't send pull requests for SPEAr
anymore due to very low traffic.

-- 
viresh