[PATCH v1 1/1] thermal: imx: implement runtime PM support
Oleksij Rempel
o.rempel at pengutronix.de
Tue Oct 19 04:51:51 PDT 2021
Hi Daniel,
On Tue, Oct 19, 2021 at 01:04:46PM +0200, Daniel Lezcano wrote:
> On 24/09/2021 13:50, Oleksij Rempel wrote:
> > Starting with commit d92ed2c9d3ff ("thermal: imx: Use driver's local
> > data to decide whether to run a measurement") this driver stared using
> > irq_enabled flag to make decision to power on/off the thermal core. This
> > triggered a regression, where after reaching critical temperature, alarm
> > IRQ handler set irq_enabled to false, disabled thermal core and was not
> > able read temperature and disable cooling sequence.
> >
> > In case the cooling device is "CPU/GPU freq", the system will run with
> > reduce performance until next reboot.
> >
> > To solve this issue, we need to move all parts implementing hand made
> > runtime power management and let it handle actual runtime PM framework.
> >
> > Fixes: d92ed2c9d3ff ("thermal: imx: Use driver's local data to decide whether to run a measurement")
> > Signed-off-by: Oleksij Rempel <o.rempel at pengutronix.de>
>
> Thanks for this fix.
>
> Petr or Oleksij,
>
> could you confirm it is tested and working without CONFIG_PM ?
Petr was right, no it is not working without PM.
> > ---
> > drivers/thermal/imx_thermal.c | 145 +++++++++++++++++++++-------------
> > 1 file changed, 91 insertions(+), 54 deletions(-)
> >
> > diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
> > index 2c7473d86a59..1db7ce6221b1 100644
> > --- a/drivers/thermal/imx_thermal.c
> > +++ b/drivers/thermal/imx_thermal.c
> > @@ -15,6 +15,7 @@
> > #include <linux/regmap.h>
> > #include <linux/thermal.h>
> > #include <linux/nvmem-consumer.h>
> > +#include <linux/pm_runtime.h>
> >
> > #define REG_SET 0x4
> > #define REG_CLR 0x8
> > @@ -194,6 +195,7 @@ static struct thermal_soc_data thermal_imx7d_data = {
> > };
> >
> > struct imx_thermal_data {
> > + struct device *dev;
> > struct cpufreq_policy *policy;
> > struct thermal_zone_device *tz;
> > struct thermal_cooling_device *cdev;
> > @@ -252,44 +254,15 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
> > const struct thermal_soc_data *soc_data = data->socdata;
> > struct regmap *map = data->tempmon;
> > unsigned int n_meas;
> > - bool wait, run_measurement;
> > u32 val;
> > + int ret;
> >
> > - run_measurement = !data->irq_enabled;
> > - if (!run_measurement) {
> > - /* Check if a measurement is currently in progress */
> > - regmap_read(map, soc_data->temp_data, &val);
> > - wait = !(val & soc_data->temp_valid_mask);
> > - } else {
> > - /*
> > - * Every time we measure the temperature, we will power on the
> > - * temperature sensor, enable measurements, take a reading,
> > - * disable measurements, power off the temperature sensor.
> > - */
> > - regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > - soc_data->power_down_mask);
> > - regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > - soc_data->measure_temp_mask);
> > -
> > - wait = true;
> > - }
> > -
> > - /*
> > - * According to the temp sensor designers, it may require up to ~17us
> > - * to complete a measurement.
> > - */
> > - if (wait)
> > - usleep_range(20, 50);
> > + ret = pm_runtime_resume_and_get(data->dev);
> > + if (ret < 0)
> > + return ret;
> >
> > regmap_read(map, soc_data->temp_data, &val);
> >
> > - if (run_measurement) {
> > - regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > - soc_data->measure_temp_mask);
> > - regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > - soc_data->power_down_mask);
> > - }
> > -
> > if ((val & soc_data->temp_valid_mask) == 0) {
> > dev_dbg(&tz->device, "temp measurement never finished\n");
> > return -EAGAIN;
> > @@ -328,6 +301,8 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
> > enable_irq(data->irq);
> > }
> >
> > + pm_runtime_put(data->dev);
> > +
> > return 0;
> > }
> >
> > @@ -335,24 +310,16 @@ static int imx_change_mode(struct thermal_zone_device *tz,
> > enum thermal_device_mode mode)
> > {
> > struct imx_thermal_data *data = tz->devdata;
> > - struct regmap *map = data->tempmon;
> > - const struct thermal_soc_data *soc_data = data->socdata;
> >
> > if (mode == THERMAL_DEVICE_ENABLED) {
> > - regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > - soc_data->power_down_mask);
> > - regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > - soc_data->measure_temp_mask);
> > + pm_runtime_get(data->dev);
> >
> > if (!data->irq_enabled) {
> > data->irq_enabled = true;
> > enable_irq(data->irq);
> > }
> > } else {
> > - regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > - soc_data->measure_temp_mask);
> > - regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > - soc_data->power_down_mask);
> > + pm_runtime_put(data->dev);
> >
> > if (data->irq_enabled) {
> > disable_irq(data->irq);
> > @@ -393,6 +360,11 @@ static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
> > int temp)
> > {
> > struct imx_thermal_data *data = tz->devdata;
> > + int ret;
> > +
> > + ret = pm_runtime_resume_and_get(data->dev);
> > + if (ret < 0)
> > + return ret;
> >
> > /* do not allow changing critical threshold */
> > if (trip == IMX_TRIP_CRITICAL)
> > @@ -406,6 +378,8 @@ static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
> >
> > imx_set_alarm_temp(data, temp);
> >
> > + pm_runtime_put(data->dev);
> > +
> > return 0;
> > }
> >
> > @@ -681,6 +655,8 @@ static int imx_thermal_probe(struct platform_device *pdev)
> > if (!data)
> > return -ENOMEM;
> >
> > + data->dev = &pdev->dev;
> > +
> > map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "fsl,tempmon");
> > if (IS_ERR(map)) {
> > ret = PTR_ERR(map);
> > @@ -801,6 +777,14 @@ static int imx_thermal_probe(struct platform_device *pdev)
> > regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > data->socdata->measure_temp_mask);
> >
> > + /* the core was configured and enabled just before */
> > + pm_runtime_set_active(&pdev->dev);
> > + pm_runtime_enable(data->dev);
> > +
> > + ret = pm_runtime_resume_and_get(data->dev);
> > + if (ret < 0)
> > + goto disable_runtime_pm;
> > +
> > data->irq_enabled = true;
> > ret = thermal_zone_device_enable(data->tz);
> > if (ret)
> > @@ -814,10 +798,17 @@ static int imx_thermal_probe(struct platform_device *pdev)
> > goto thermal_zone_unregister;
> > }
> >
> > + ret = pm_runtime_put(data->dev);
> > + if (ret < 0)
> > + goto disable_runtime_pm;
> > +
> > return 0;
> >
> > thermal_zone_unregister:
> > thermal_zone_device_unregister(data->tz);
> > +disable_runtime_pm:
> > + pm_runtime_put_noidle(data->dev);
> > + pm_runtime_disable(data->dev);
> > clk_disable:
> > clk_disable_unprepare(data->thermal_clk);
> > legacy_cleanup:
> > @@ -829,13 +820,9 @@ static int imx_thermal_probe(struct platform_device *pdev)
> > static int imx_thermal_remove(struct platform_device *pdev)
> > {
> > struct imx_thermal_data *data = platform_get_drvdata(pdev);
> > - struct regmap *map = data->tempmon;
> >
> > - /* Disable measurements */
> > - regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > - data->socdata->power_down_mask);
> > - if (!IS_ERR(data->thermal_clk))
> > - clk_disable_unprepare(data->thermal_clk);
> > + pm_runtime_put_noidle(data->dev);
> > + pm_runtime_disable(data->dev);
> >
> > thermal_zone_device_unregister(data->tz);
> > imx_thermal_unregister_legacy_cooling(data);
> > @@ -858,29 +845,79 @@ static int __maybe_unused imx_thermal_suspend(struct device *dev)
> > ret = thermal_zone_device_disable(data->tz);
> > if (ret)
> > return ret;
> > +
> > + return pm_runtime_force_suspend(data->dev);
> > +}
> > +
> > +static int __maybe_unused imx_thermal_resume(struct device *dev)
> > +{
> > + struct imx_thermal_data *data = dev_get_drvdata(dev);
> > + int ret;
> > +
> > + ret = pm_runtime_force_resume(data->dev);
> > + if (ret)
> > + return ret;
> > + /* Enabled thermal sensor after resume */
> > + return thermal_zone_device_enable(data->tz);
> > +}
> > +
> > +static int __maybe_unused imx_thermal_runtime_suspend(struct device *dev)
> > +{
> > + struct imx_thermal_data *data = dev_get_drvdata(dev);
> > + const struct thermal_soc_data *socdata = data->socdata;
> > + struct regmap *map = data->tempmon;
> > + int ret;
> > +
> > + ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
> > + socdata->measure_temp_mask);
> > + if (ret)
> > + return ret;
> > +
> > + ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
> > + socdata->power_down_mask);
> > + if (ret)
> > + return ret;
> > +
> > clk_disable_unprepare(data->thermal_clk);
> >
> > return 0;
> > }
> >
> > -static int __maybe_unused imx_thermal_resume(struct device *dev)
> > +static int __maybe_unused imx_thermal_runtime_resume(struct device *dev)
> > {
> > struct imx_thermal_data *data = dev_get_drvdata(dev);
> > + const struct thermal_soc_data *socdata = data->socdata;
> > + struct regmap *map = data->tempmon;
> > int ret;
> >
> > ret = clk_prepare_enable(data->thermal_clk);
> > if (ret)
> > return ret;
> > - /* Enabled thermal sensor after resume */
> > - ret = thermal_zone_device_enable(data->tz);
> > +
> > + ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
> > + socdata->power_down_mask);
> > + if (ret)
> > + return ret;
> > +
> > + ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
> > + socdata->measure_temp_mask);
> > if (ret)
> > return ret;
> >
> > + /*
> > + * According to the temp sensor designers, it may require up to ~17us
> > + * to complete a measurement.
> > + */
> > + usleep_range(20, 50);
> > +
> > return 0;
> > }
> >
> > -static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
> > - imx_thermal_suspend, imx_thermal_resume);
> > +static const struct dev_pm_ops imx_thermal_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(imx_thermal_suspend, imx_thermal_resume)
> > + SET_RUNTIME_PM_OPS(imx_thermal_runtime_suspend,
> > + imx_thermal_runtime_resume, NULL)
> > +};
> >
> > static struct platform_driver imx_thermal = {
> > .driver = {
> >
>
>
> --
> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>
> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
> <http://twitter.com/#!/linaroorg> Twitter |
> <http://www.linaro.org/linaro-blog/> Blog
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the linux-arm-kernel
mailing list