[PATCH 3/3] thermal: mediatek: add MT8365 thermal driver support
Daniel Lezcano
daniel.lezcano at linaro.org
Sat Oct 16 13:06:28 PDT 2021
On 14/10/2021 15:56, Markus Schneider-Pargmann wrote:
> From: Fabien Parent <fparent at baylibre.com>
>
> mt8365 is similar to the other SoCs supported by the driver. It has only
> one bank and 3 sensors that can be multiplexed.
>
> Additionally the buffer has to be enabled and connected to AUXADC
> similar to the V2 version but at a different register offset. That's why
> I added three new configuration values to define the register, mask and
> bits to be set to be able to use it for both V2 and mt8365.
>
> Signed-off-by: Fabien Parent <fparent at baylibre.com>
> [Added apmixed control register logic]
> Signed-off-by: Markus Schneider-Pargmann <msp at baylibre.com>
> ---
> drivers/thermal/mtk_thermal.c | 91 ++++++++++++++++++++++++++++++++---
> 1 file changed, 85 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 93ee043d70da..7a75ae8231f2 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -31,6 +31,7 @@
> #define AUXADC_CON2_V 0x010
> #define AUXADC_DATA(channel) (0x14 + (channel) * 4)
>
> +#define APMIXED_SYS_TS_CON0 0x600
> #define APMIXED_SYS_TS_CON1 0x604
>
> /* Thermal Controller Registers */
> @@ -245,6 +246,17 @@ enum mtk_thermal_version {
> /* The calibration coefficient of sensor */
> #define MT8183_CALIBRATION 153
>
> +/* MT8365 */
> +#define MT8365_TEMP_AUXADC_CHANNEL 11
> +#define MT8365_CALIBRATION 164
> +#define MT8365_NUM_CONTROLLER 1
> +#define MT8365_NUM_BANKS 1
> +#define MT8365_NUM_SENSORS 3
> +#define MT8365_NUM_SENSORS_PER_ZONE 3
You can get rid of these macros by using ARRAY_SIZE.
eg.
static const int mt8365_bank_data[] = {
MT8365_TS1,
MT8365_TS2,
MT8365_TS3
};
...
.num_sensors = ARRAY_SIZE(mt8365_bank_data);
...
> +#define MT8365_TS1 0
> +#define MT8365_TS2 1
> +#define MT8365_TS3 2
> +
> struct mtk_thermal;
>
> struct thermal_bank_cfg {
> @@ -271,6 +283,9 @@ struct mtk_thermal_data {
> bool need_switch_bank;
> struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
> enum mtk_thermal_version version;
> + u32 apmixed_buffer_ctl_reg;
> + u32 apmixed_buffer_ctl_mask;
> + u32 apmixed_buffer_ctl_set;
> };
>
> struct mtk_thermal {
> @@ -386,6 +401,24 @@ static const int mt7622_mux_values[MT7622_NUM_SENSORS] = { 0, };
> static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 };
> static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, };
>
> +/* MT8365 thermal sensor data */
> +static const int mt8365_bank_data[MT8365_NUM_SENSORS] = {
> + MT8365_TS1, MT8365_TS2, MT8365_TS3
> +};
> +
> +static const int mt8365_msr[MT8365_NUM_SENSORS_PER_ZONE] = {
> + TEMP_MSR0, TEMP_MSR1, TEMP_MSR2
> +};
> +
> +static const int mt8365_adcpnp[MT8365_NUM_SENSORS_PER_ZONE] = {
> + TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2
> +};
> +
> +static const int mt8365_mux_values[MT8365_NUM_SENSORS] = { 0, 1, 2 };
> +static const int mt8365_tc_offset[MT8365_NUM_CONTROLLER] = { 0 };
> +
> +static const int mt8365_vts_index[MT8365_NUM_SENSORS] = { VTS1, VTS2, VTS3 };
> +
> /*
> * The MT8173 thermal controller has four banks. Each bank can read up to
> * four temperature sensors simultaneously. The MT8173 has a total of 5
> @@ -460,6 +493,40 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
> .version = MTK_THERMAL_V1,
> };
>
> +/*
> + * The MT8365 thermal controller has one bank, which can read up to
> + * four temperature sensors simultaneously. The MT8365 has a total of 3
> + * temperature sensors.
> + *
> + * The thermal core only gets the maximum temperature of this one bank,
> + * so the bank concept wouldn't be necessary here. However, the SVS (Smart
> + * Voltage Scaling) unit makes its decisions based on the same bank
> + * data.
> + */
> +static const struct mtk_thermal_data mt8365_thermal_data = {
> + .auxadc_channel = MT8365_TEMP_AUXADC_CHANNEL,
> + .num_banks = MT8365_NUM_BANKS,
> + .num_sensors = MT8365_NUM_SENSORS,
> + .vts_index = mt8365_vts_index,
> + .cali_val = MT8365_CALIBRATION,
> + .num_controller = MT8365_NUM_CONTROLLER,
> + .controller_offset = mt8365_tc_offset,
> + .need_switch_bank = false,
> + .bank_data = {
> + {
> + .num_sensors = MT8365_NUM_SENSORS,
> + .sensors = mt8365_bank_data
> + },
> + },
> + .msr = mt8365_msr,
> + .adcpnp = mt8365_adcpnp,
> + .sensor_mux_values = mt8365_mux_values,
> + .version = MTK_THERMAL_V1,
> + .apmixed_buffer_ctl_reg = APMIXED_SYS_TS_CON0,
> + .apmixed_buffer_ctl_mask = ~(u32)GENMASK(29, 28),
> + .apmixed_buffer_ctl_set = 0,
> +};
> +
> /*
> * The MT2712 thermal controller has one bank, which can read up to
> * four temperature sensors simultaneously. The MT2712 has a total of 4
> @@ -514,6 +581,9 @@ static const struct mtk_thermal_data mt7622_thermal_data = {
> .adcpnp = mt7622_adcpnp,
> .sensor_mux_values = mt7622_mux_values,
> .version = MTK_THERMAL_V2,
> + .apmixed_buffer_ctl_reg = APMIXED_SYS_TS_CON1,
> + .apmixed_buffer_ctl_mask = ~0x37,
> + .apmixed_buffer_ctl_set = 0x1,
Please change those literal into macros
> };
>
> /*
> @@ -958,19 +1028,27 @@ static const struct of_device_id mtk_thermal_of_match[] = {
> {
> .compatible = "mediatek,mt8183-thermal",
> .data = (void *)&mt8183_thermal_data,
> + },
> + {
> + .compatible = "mediatek,mt8365-thermal",
> + .data = (void *)&mt8365_thermal_data,
Is this cast really needed ?
> }, {
> },
> };
> MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
>
> -static void mtk_thermal_turn_on_buffer(void __iomem *apmixed_base)
> +static void mtk_thermal_turn_on_buffer(struct mtk_thermal *mt,
> + void __iomem *apmixed_base)
> {
> int tmp;
>
> - tmp = readl(apmixed_base + APMIXED_SYS_TS_CON1);
> - tmp &= ~(0x37);
> - tmp |= 0x1;
> - writel(tmp, apmixed_base + APMIXED_SYS_TS_CON1);
> + if (!mt->conf->apmixed_buffer_ctl_reg)
> + return;
> +
> + tmp = readl(apmixed_base + mt->conf->apmixed_buffer_ctl_reg);
> + tmp &= mt->conf->apmixed_buffer_ctl_mask;
> + tmp |= mt->conf->apmixed_buffer_ctl_set;
What is the goal of these two bits operations ?
> + writel(tmp, apmixed_base + mt->conf->apmixed_buffer_ctl_reg);
> udelay(200);
> }
>
> @@ -1070,8 +1148,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> goto err_disable_clk_auxadc;
> }
>
> + mtk_thermal_turn_on_buffer(mt, apmixed_base);
> +
> if (mt->conf->version == MTK_THERMAL_V2) {
> - mtk_thermal_turn_on_buffer(apmixed_base);
> mtk_thermal_release_periodic_ts(mt, auxadc_base);
> }
>
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
More information about the linux-arm-kernel
mailing list