[PATCH] arm64: dts: imx8mm: Add CSI nodes
Adam Ford
aford173 at gmail.com
Fri Oct 15 16:48:54 PDT 2021
On Fri, Oct 15, 2021 at 6:05 PM Adam Ford <aford173 at gmail.com> wrote:
>
> On Fri, Oct 15, 2021 at 5:39 PM Laurent Pinchart
> <laurent.pinchart at ideasonboard.com> wrote:
> >
> > Hi Adam,
> >
> > On Fri, Oct 15, 2021 at 05:26:03PM -0500, Adam Ford wrote:
> > > On Thu, Oct 14, 2021 at 4:16 PM Laurent Pinchart wrote:
> > > > On Thu, Oct 14, 2021 at 03:32:33PM -0500, Adam Ford wrote:
> > > > > On Wed, Oct 13, 2021 at 9:52 PM Adam Ford wrote:
> > > > > >
> > > > > > There is a csi bridge and csis interface that tie together
> > > > > > to allow csi2 capture.
> > > > > >
> > > > > > Signed-off-by: Adam Ford <aford173 at gmail.com>
> > > > >
> > > > > Laurent,
> > > > >
> > > > > Since you did some work to make the csis functional on the imx8mm, I
> > > > > was hoping you might have some insights. Please see below:
> > > > >
> > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > > > index c2f3f118f82e..8a8a5d0a4a1e 100644
> > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > > > @@ -1068,6 +1068,22 @@ aips4: bus at 32c00000 {
> > > > > > #size-cells = <1>;
> > > > > > ranges = <0x32c00000 0x32c00000 0x400000>;
> > > > > >
> > > > > > + csi: csi at 32e20000 {
> > > > > > + compatible = "fsl,imx7-csi";
> > > >
> > > > This should be
> > > >
> > > > compatible = "fsl,imx8mm-csi", "fsl,imx7-csi";;
> > > >
> > > > > > + reg = <0x32e20000 0x1000>;
> > > > > > + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> > > > > > + clocks = <&clk IMX8MM_CLK_CSI1_ROOT>;
> > > > > > + clock-names = "mclk";
> > > > > > + power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_CSI_BRIDGE>;
> > > > > > + status = "disabled";
> > > > > > +
> > > > > > + port {
> > > > > > + csi_in: endpoint {
> > > > > > + remote-endpoint = <&imx8mm_mipi_csi_out>;
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > disp_blk_ctrl: blk-ctrl at 32e28000 {
> > > > > > compatible = "fsl,imx8mm-disp-blk-ctrl", "syscon";
> > > > > > reg = <0x32e28000 0x100>;
> > > > > > @@ -1095,6 +1111,41 @@ disp_blk_ctrl: blk-ctrl at 32e28000 {
> > > > > > #power-domain-cells = <1>;
> > > > > > };
> > > > > >
> > > > > > + mipi_csi2: mipi-csi at 32e30000 {
> > > > > > + compatible = "fsl,imx8mm-mipi-csi2";
> > > > > > + reg = <0x32e30000 0x1000>;
> > > > > > + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> > > > > > + clock-frequency = <333000000>;
> > > > > > + clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>,
> > > > > > + <&clk IMX8MM_CLK_CSI1_ROOT>,
> > > > > > + <&clk IMX8MM_CLK_CSI1_PHY_REF>,
> > > > > > + <&clk IMX8MM_CLK_DISP_AXI_ROOT>;
> > > > >
> > > > > When comparing clock parents and the clock rates to one of NXP's
> > > > > kernels, it appears we need assigned-clocks and assigned-clock-parents
> > > > > to allow the CSI1 clocks to run fast enough.
> > > > >
> > > > > assigned-clocks = <&clk IMX8MM_CLK_CSI1_PHY_REF>,
> > > > > <&clk IMX8MM_CLK_CSI1_CORE>,
> > > > > <&clk IMX8MM_CLK_CSI1_ROOT>,
> > > > > <&clk IMX8MM_CLK_CSI1_ESC>;
> > > > > assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
> > > > > <&clk IMX8MM_SYS_PLL2_1000M>,
> > > > > <&clk IMX8MM_CLK_CSI1_CORE>,
> > > > > <&clk IMX8MM_SYS_PLL1_800M>;
> > > > >
> > > > > However, even with this, I am attempting to capture. While I can get
> > > > > the pipeline enabled, when I try to capture a file, I get no data. i
> > > > > can use control-c to exit gstreamer, so I know the kernel didn't hang.
> > > > > I don't get errors, but I don't get data either.
> > > > >
> > > > > Any ideas if what/if any other clock entries might be missing?
> > > >
> > > > Have you tried looking at the error interrupt counters to see if the
> > > > CSI-2 bus side operates as expected ? I'd start there before blaming the
> > > > clocks. Note that the issue could also be in the CSI bridge.
> > >
> > > I am not seeing interrupts on either the CSI, mipi-csi, or err:
> > >
> > > 54: 0 0 0 0 GICv3 48 Level csi
> > > 55: 0 0 0 0 GICv3 49 Level
> > > 32e30000.mipi-csi
> > > Err: 0
> > >
> > > > I've had issues capturing from one particular sensor on an i.MX8MM
> > > > board, where I would get images, but with heavy corruption. The problem
> > > > was solved by chance when trying a different SPL binary. I need to
> > >
> > > I wonder if the issue was related to different versions of ATF, and
> > > depending on the power domain controls used, it could have been using
> > > ATF to set the power domains.
> > > I've had issues in the past too, but I have tried a couple different
> > > binaries, and I am not seeing a change in behavior.
> >
> > We've just finished the investigation, and it turned out to be related
> > to the clock frequencies. Here's the DT changes we had to make to get it
> > working:
> >
> > assigned-clocks = <&clk IMX8MM_CLK_DISP_AXI>,
> > <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
> > <&clk IMX8MM_CLK_DISP_APB>,
> > <&clk IMX8MM_CLK_DISP_APB_ROOT>;
> > assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
> > <&clk IMX8MM_CLK_DISP_AXI>,
> > <&clk IMX8MM_SYS_PLL1_800M>,
> > <&clk IMX8MM_CLK_DISP_APB>;
> > assigned-clock-rates = <500000000>, <500000000>, <200000000>, <200000000>;
> >
> > This results in the following clock configuration:
> >
> > sys_pll2_1000m 1000000000
> > disp_axi 500000000
> > disp_axi_root_clk 500000000
> >
> > sys_pll1_800m 800000000
> > disp_apb 200000000
> > disp_apb_root_clk 200000000
> >
> > I'll check which clock is the culprit, and see if we could program the
> > clocks in the driver directly.
>
> I am using Shawn Guo's "for-next" branch, and by default the disp_axi
> and disp_apb clocks appear to already have these parents and clock
> rates. They appear to be defined in the pgc_dispmix node.
>
> disp_axi 1 1 0 500000000
> 0 0 50000 Y
> disp_axi_root_clk 2 2 0 500000000
> 0 0 50000 Y
> disp_apb 1 1 0 200000000
> 0 0 50000 Y
> disp_apb_root_clk 2 2 0 200000000
> 0 0 50000 Y
>
> Can you tell me which branch you're using? I wonder if I should
> switch branches.
>
I started investigating the power domain, and I did a dump of the
disp-blk-ctl dump, and it appears the csi power domain is remaining
off:
cat /sys/kernel/debug/regmap/32e28000.blk-ctrl/registers
00: 00000047
04: 0000103f
I compared it with pm_genpd_summary, and found the dispblk-mipi-csi
appears to be off:
dispblk-csi-bridge on
/devices/platform/soc at 0/32c00000.bus/32e20000.csi
dispblk-mipi-csi off-0
0
/devices/platform/soc at 0/32c00000.bus/32e30000.mipi-csi
suspended 0
Do you have any idea why the dispblk-mipi-csi power domain might turn
off while the dispblk-csi-bridge is on?
I added some debug code, and it looks like we're intentionally turning
it off, but it's not clear as to why.
> adam
> >
> > > > investigate the differences there, and possibly update the driver
> > > > accordingly. It may or may not be related to your issue.
> > > >
> > > > Apart from the compatible string issue mentioned above, the bindings
> > > > match what I am using, so, with the compatible string fixed,
> > >
> > > Out of curiosity, I noticed the default csi clock parents point to a
> > > 24MHz clock, but the csi-2 interface wants to set the clock to 333MHz.
> > > Any chance you could share your clk_summary?
> >
> > Is the above information what you need ?
> >
> > > > Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> > >
> > > Thanks for the review
> > >
> > > > > > + clock-names = "pclk", "wrap", "phy", "axi";
> > > > > > + power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_MIPI_CSI>;
> > > > > > + status = "disabled";
> > > > > > +
> > > > > > + ports {
> > > > > > + #address-cells = <1>;
> > > > > > + #size-cells = <0>;
> > > > > > +
> > > > > > + port at 0 {
> > > > > > + reg = <0>;
> > > > > > +
> > > > > > + imx8mm_mipi_csi_in: endpoint {
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > + port at 1 {
> > > > > > + reg = <1>;
> > > > > > +
> > > > > > + imx8mm_mipi_csi_out: endpoint {
> > > > > > + remote-endpoint = <&csi_in>;
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > + };
> > > > > > +
> > > > > > +
> > > > > > usbotg1: usb at 32e40000 {
> > > > > > compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
> > > > > > reg = <0x32e40000 0x200>;
> >
> > --
> > Regards,
> >
> > Laurent Pinchart
More information about the linux-arm-kernel
mailing list