[PATCH v5] arm64: dts: marvell: add Globalscale MOCHAbin
Robert Marko
robert.marko at sartura.hr
Fri Oct 8 06:28:38 PDT 2021
On Fri, Oct 8, 2021 at 2:08 PM Pali Rohár <pali at kernel.org> wrote:
>
> Hello! See some notes below.
>
> On Friday 08 October 2021 13:43:43 Robert Marko wrote:
> > Globalscale MOCHAbin is a Armada 7040 based development board.
> >
> > Specifications:
> > * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
> > * 2 / 4 / 8 GB of DDR4 DRAM
> > * 16 GB eMMC
> > * 4MB SPI-NOR (Bootloader)
> > * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
> > * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
> > * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
> > * 1x SATA 7+15 socket (SATA3)
> > * 1x 16-pin (2×8) MikroBus Connector
> > * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
> > * 2x USB3.0 Type-A ports via SMSC USB5434B hub
> > * Cortex 2x5 JTAG
> > * microUSB port for UART (PL2303GL/PL2303SA onboard)
> > * 1x 10G SFP+
> > * 1x 1G SFP (Connected to 88E1512 PHY)
> > * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
> > * 4x 1G RJ45 ports via Topaz 88E6141 switch
> > * RTC with battery holder (SoC provided, requires CR2032 battery)
> > * 1x 12V DC IN
> > * 1x Power switch
> > * 1x 12V fan header (3-pin, power only)
> > * 1x mini-PCIe LED header (2x0.1" pins)
> > * 1x M.2-2280 LED header (2x0.1" pins)
> > * 6x Bootstrap jumpers
> > * 1x Power LED (Green)
> > * 3x Tri-color RGB LEDs (Controllable)
> > * 1x Microchip ATECC608B secure element
> >
> > Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
> > parallel connected to the same PHY.
>
> + Marek
>
> Robert, how it works? Is there some detection which source port (SFP or
> WAN) should be activated? And what happens if you plug SFP module and
> also 1G WAN at the same time?
Hi, Pali.
It works due to the Marvell PHY driver adding support for attaching an
SFP recently
specifically for the 88E151x family.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/net/phy/marvell.c?h=v5.15-rc4&id=b697d9d38a5a5ab405d7cc4743d39fe2c5d7517c
It simply uses the standard SFP driver as the SFP cage is properly
connected to see if a
the compatible module is connected and if so configures the 88E1512 to
SGMII/1000Base-X/100Base-FX modes
and attaches the SFP bus to the upstream ethernet controller so that
you can use ethtool on it.
So if you plug in an SFP module and then copper it will continue using
the SFP module until its removed at which
the time it will reconfigure the PHY back to copper mode.
And if you plug in SFP after copper it will use it again as the
presence status triggers it.
>
> > Signed-off-by: Robert Marko <robert.marko at sartura.hr>
> > Reviewed-by: Andrew Lunn <andrew at lunn.ch>
> > ---
> > Changes in v5:
> > * Change LED labels to use the common "color:name" format instead
> >
> > Changes in v4:
> > * Rename the "u-boot" partition to "firmware" which is more appropriate
> > as it a concatenation of mv-ddr + TF-A + U-boot
> >
> > Changes in v3:
> > * Use IRQ_TYPE_LEVEL_LOW instead of IRQ_TYPE_EDGE_FALLING as both the
> > PCA9554 and Topaz switch have an active LOW IRQ signal.
> >
> > Changes in v2:
> > * Use "10gbase-r" instead of "10gbase-kr"
> > ---
> > arch/arm64/boot/dts/marvell/Makefile | 1 +
> > .../boot/dts/marvell/armada-7040-mochabin.dts | 452 ++++++++++++++++++
> > 2 files changed, 453 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
> >
> > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> > index 34efe0fb6f37..4d3a2ae9adbd 100644
> > --- a/arch/arm64/boot/dts/marvell/Makefile
> > +++ b/arch/arm64/boot/dts/marvell/Makefile
> > @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> > +dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
> > diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
> > new file mode 100644
> > index 000000000000..61f3104a18cf
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
> > @@ -0,0 +1,452 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Device Tree file for Globalscale MOCHAbin
> > + * Copyright (C) 2019 Globalscale technologies, Inc.
> > + * Copyright (C) 2021 Sartura Ltd.
> > + *
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include "armada-7040.dtsi"
> > +
> > +/ {
> > + model = "Globalscale MOCHAbin";
> > + compatible = "globalscale,mochabin", "marvell,armada7040",
> > + "marvell,armada-ap806-quad", "marvell,armada-ap806";
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + aliases {
> > + ethernet0 = &cp0_eth0;
> > + ethernet1 = &cp0_eth1;
> > + ethernet2 = &cp0_eth2;
> > + ethernet3 = &swport1;
> > + ethernet4 = &swport2;
> > + ethernet5 = &swport3;
> > + ethernet6 = &swport4;
> > + };
> > +
> > + /* SFP+ 10G */
> > + sfp_eth0: sfp-eth0 {
> > + compatible = "sff,sfp";
> > + i2c-bus = <&cp0_i2c1>;
> > + los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
> > + mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
> > + tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
> > + tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + /* SFP 1G */
> > + sfp_eth2: sfp-eth2 {
> > + compatible = "sff,sfp";
> > + i2c-bus = <&cp0_i2c0>;
> > + los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
> > + mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
> > + tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
> > + tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
> > + };
> > +};
> > +
> > +/* microUSB UART console */
> > +&uart0 {
> > + status = "okay";
> > +
> > + pinctrl-0 = <&uart0_pins>;
> > + pinctrl-names = "default";
> > +};
> > +
> > +/* eMMC */
> > +&ap_sdhci0 {
> > + status = "okay";
> > +
> > + bus-width = <4>;
> > + non-removable;
> > + /delete-property/ marvell,xenon-phy-slow-mode;
> > + no-1-8-v;
> > +};
> > +
> > +&cp0_pinctrl {
> > + cp0_uart0_pins: cp0-uart0-pins {
> > + marvell,pins = "mpp6", "mpp7";
> > + marvell,function = "uart0";
> > + };
> > +
> > + cp0_spi0_pins: cp0-spi0-pins {
> > + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59";
> > + marvell,function = "spi0";
> > + };
> > +
> > + cp0_spi1_pins: cp0-spi1-pins {
> > + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> > + marvell,function = "spi1";
> > + };
> > +
> > + cp0_i2c0_pins: cp0-i2c0-pins {
> > + marvell,pins = "mpp37", "mpp38";
> > + marvell,function = "i2c0";
> > + };
> > +
> > + cp0_i2c1_pins: cp0-i2c1-pins {
> > + marvell,pins = "mpp2", "mpp3";
> > + marvell,function = "i2c1";
> > + };
> > +
> > + pca9554_int_pins: pca9554-int-pins {
> > + marvell,pins = "mpp27";
> > + marvell,function = "gpio";
> > + };
> > +
> > + cp0_rgmii1_pins: cp0-rgmii1-pins {
> > + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
> > + "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
> > + marvell,function = "ge1";
> > + };
> > +
> > + is31_sdb_pins: is31-sdb-pins {
> > + marvell,pins = "mpp30";
> > + marvell,function = "gpio";
> > + };
> > +
> > + cp0_pcie_reset_pins: cp0-pcie-reset-pins {
> > + marvell,pins = "mpp9";
> > + marvell,function = "gpio";
>
> Now I spotted this. Why is PERST# pin configured into gpio mode? Is
> there some issue that this pin in pcie mode is not working properly,
> that PCIe controller cannot handle it correctly? Or something else?
Its because I have seen way too many broken controllers when it comes
to PERST and
other Armada 7k/8k devices are using it in GPIO mode as well.
Just look at the number of conversions back to GPIO for other
platforms as there is always some bug.
>
> > + };
> > +
> > + cp0_switch_pins: cp0-switch-pins {
> > + marvell,pins = "mpp0", "mpp1";
> > + marvell,function = "gpio";
> > + };
> > +
> > + cp0_phy_pins: cp0-phy-pins {
> > + marvell,pins = "mpp12";
> > + marvell,function = "gpio";
> > + };
> > +};
> > +
> > +/* mikroBUS UART */
> > +&cp0_uart0 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_uart0_pins>;
> > +};
> > +
> > +/* mikroBUS SPI */
> > +&cp0_spi0 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_spi0_pins>;
> > +};
> > +
> > +/* SPI-NOR */
> > +&cp0_spi1{
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_spi1_pins>;
> > +
> > + spi-flash at 0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "jedec,spi-nor";
> > + reg = <0>;
> > + spi-max-frequency = <20000000>;
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition at 0 {
> > + label = "firmware";
> > + reg = <0x0 0x3e0000>;
> > + read-only;
> > + };
> > +
> > + partition at 3e0000 {
> > + label = "hw-info";
> > + reg = <0x3e0000 0x10000>;
> > + read-only;
> > + };
> > +
> > + partition at 3f0000 {
> > + label = "u-boot-env";
> > + reg = <0x3f0000 0x10000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +/* mikroBUS, 1G SFP and GPIO expander */
> > +&cp0_i2c0 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_i2c0_pins>;
> > + clock-frequency = <100000>;
> > +
> > + sfp_gpio: pca9554 at 39 {
> > + compatible = "nxp,pca9554";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pca9554_int_pins>;
> > + reg = <0x39>;
> > +
> > + interrupt-parent = <&cp0_gpio1>;
> > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > +
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > +
> > + /*
> > + * IO0_0: SFP+_TX_FAULT
> > + * IO0_1: SFP+_TX_DISABLE
> > + * IO0_2: SFP+_PRSNT
> > + * IO0_3: SFP+_LOSS
> > + * IO0_4: SFP_TX_FAULT
> > + * IO0_5: SFP_TX_DISABLE
> > + * IO0_6: SFP_PRSNT
> > + * IO0_7: SFP_LOSS
> > + */
> > + };
> > +};
> > +
> > +/* IS31FL3199, mini-PCIe and 10G SFP+ */
> > +&cp0_i2c1 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_i2c1_pins>;
> > + clock-frequency = <100000>;
> > +
> > + leds at 64 {
> > + compatible = "issi,is31fl3199";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&is31_sdb_pins>;
> > + shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>;
> > + reg = <0x64>;
> > +
> > + led1_red: led at 1 {
> > + label = "red:led1";
> > + reg = <1>;
> > + led-max-microamp = <20000>;
> > + };
> > +
> > + led1_green: led at 2 {
> > + label = "green:led1";
> > + reg = <2>;
> > + };
> > +
> > + led1_blue: led at 3 {
> > + label = "blue:led1";
> > + reg = <3>;
> > + };
> > +
> > + led2_red: led at 4 {
> > + label = "red:led2";
> > + reg = <4>;
> > + };
> > +
> > + led2_green: led at 5 {
> > + label = "green:led2";
> > + reg = <5>;
> > + };
> > +
> > + led2_blue: led at 6 {
> > + label = "blue:led2";
> > + reg = <6>;
> > + };
> > +
> > + led3_red: led at 7 {
> > + label = "red:led3";
> > + reg = <7>;
> > + };
> > +
> > + led3_green: led at 8 {
> > + label = "green:led3";
> > + reg = <8>;
> > + };
> > +
> > + led3_blue: led at 9 {
> > + label = "blue:led3";
> > + reg = <9>;
> > + };
> > + };
> > +};
> > +
> > +&cp0_mdio {
> > + status = "okay";
> > +
> > + /* 88E1512 PHY */
> > + eth2phy: ethernet-phy at 1 {
> > + reg = <1>;
> > + sfp = <&sfp_eth2>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_phy_pins>;
> > + reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + /* 88E6141 Topaz switch */
> > + switch: switch at 3 {
> > + compatible = "marvell,mv88e6085";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <3>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_switch_pins>;
> > + reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>;
> > +
> > + interrupt-parent = <&cp0_gpio1>;
> > + interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + swport1: port at 1 {
> > + reg = <1>;
> > + label = "lan0";
> > + phy-handle = <&swphy1>;
> > + };
> > +
> > + swport2: port at 2 {
> > + reg = <2>;
> > + label = "lan1";
> > + phy-handle = <&swphy2>;
> > + };
> > +
> > + swport3: port at 3 {
> > + reg = <3>;
> > + label = "lan2";
> > + phy-handle = <&swphy3>;
> > + };
> > +
> > + swport4: port at 4 {
> > + reg = <4>;
> > + label = "lan3";
> > + phy-handle = <&swphy4>;
> > + };
> > +
> > + port at 5 {
> > + reg = <5>;
> > + label = "cpu";
> > + ethernet = <&cp0_eth1>;
> > + phy-mode = "2500base-x";
> > + managed = "in-band-status";
> > + };
> > + };
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + swphy1: swphy1 at 17 {
> > + reg = <17>;
> > + };
> > +
> > + swphy2: swphy2 at 18 {
> > + reg = <18>;
> > + };
> > +
> > + swphy3: swphy3 at 19 {
> > + reg = <19>;
> > + };
> > +
> > + swphy4: swphy4 at 20 {
> > + reg = <20>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&cp0_ethernet {
> > + status = "okay";
> > +};
> > +
> > +/* 10G SFP+ */
> > +&cp0_eth0 {
> > + status = "okay";
> > +
> > + phy-mode = "10gbase-r";
> > + phys = <&cp0_comphy4 0>;
> > + managed = "in-band-status";
> > + sfp = <&sfp_eth0>;
> > +};
> > +
> > +/* Topaz switch uplink */
> > +&cp0_eth1 {
> > + status = "okay";
> > +
> > + phy-mode = "2500base-x";
> > + phys = <&cp0_comphy0 1>;
> > +
> > + fixed-link {
> > + speed = <2500>;
> > + full-duplex;
> > + };
> > +};
> > +
> > +/* 1G SFP or 1G RJ45 */
> > +&cp0_eth2 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_rgmii1_pins>;
> > +
> > + phy = <ð2phy>;
> > + phy-mode = "rgmii-id";
> > +};
> > +
> > +&cp0_utmi {
> > + status = "okay";
> > +};
> > +
> > +/* SMSC USB5434B hub */
> > +&cp0_usb3_0 {
> > + status = "okay";
> > +
> > + phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
> > + phy-names = "cp0-usb3h0-comphy", "utmi";
> > +};
> > +
> > +/* miniPCI-E USB */
> > +&cp0_usb3_1 {
> > + status = "okay";
> > +};
> > +
> > +&cp0_sata0 {
> > + status = "okay";
> > +
> > + /* 7 + 12 SATA connector (J24) */
> > + sata-port at 0 {
> > + phys = <&cp0_comphy2 0>;
> > + phy-names = "cp0-sata0-0-phy";
> > + };
> > +
> > + /* M.2-2250 B-key (J39) */
> > + sata-port at 1 {
> > + phys = <&cp0_comphy3 1>;
> > + phy-names = "cp0-sata0-1-phy";
> > + };
> > +};
> > +
> > +/* miniPCI-E (J5) */
> > +&cp0_pcie2 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cp0_pcie_reset_pins>;
> > + phys = <&cp0_comphy5 2>;
> > + phy-names = "cp0-pcie2-x1-phy";
> > + reset-gpio = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>;
>
> Per snps,dw-pcie.yaml file is 'reset-gpio' property deprecated. There
> is 'reset-gpios' property which should be used according pci.txt file.
Yeah, just saw it now, will update the property.
Regards,
Robert
>
> > +};
> > --
> > 2.33.0
> >
--
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko at sartura.hr
Web: www.sartura.hr
More information about the linux-arm-kernel
mailing list