[PATCH v3 2/7] arm64: dts: freescale: add initial device tree for TQMa8MQML with i.MX8MM
Alexander Stein
alexander.stein at ew.tq-group.com
Tue Nov 30 23:29:43 PST 2021
This adds support for TQMa8MQML module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein at ew.tq-group.com>
---
Changes in v3:
* Fix node name for audio-codec
* Use matrix instead of array for 'fsl,pins'
Changes in v2:
* Fixed ordering in Makefile
* Renamed codec -> audio_codec
* Add USB interfaces & USB extcon & pinctrl nodes
* Fixed pinctrl node names
* Removed empty chosen node
* Removed regulator-always-on on non-switchable regulators
* Changed spi-tx-bus-width for spi-nor flash similar to commit 04aa946d57b2
("arm64: dts: imx8: change the spi-nor tx")
* Enabled gpu_2d and gpu_3d nodes
* Removed Ethernet PHY IRQ support (was unreliable)
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 253 +++++++++++++
.../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 335 ++++++++++++++++++
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 282 +++++++++++++++
4 files changed, 871 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a14a6173b765..33c21322bf15 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
new file mode 100644
index 000000000000..7844878788f4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
+ compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc1;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+
+ extcon_usbotg1: extcon-usbotg1 {
+ compatible = "linux,extcon-usb-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1_extcon>;
+ id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&i2c1 {
+ expander2: gpio at 27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+ <&clk IMX8MM_AUDIO_PLL2_OUT>;
+};
+
+&tlv320aic3x04 {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+};
+
+&uart1 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&uart2 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ dr_mode = "otg";
+ extcon = <&extcon_usbotg1>;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ power-active-high;
+ over-current-active-low;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ vbus-supply = <®_hub_vbus>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006>;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006>,
+ <MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006>;
+ };
+
+ pinctrl_expander: expandergrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94>;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002>,
+ <MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002>,
+ <MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14>,
+ <MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14>,
+ <MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14>,
+ <MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14>,
+ <MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90>,
+ <MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90>,
+ <MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90>,
+ <MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90>,
+ <MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14>,
+ <MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90>,
+ <MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90>,
+ <MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14>;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84>,
+ <MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84>,
+ <MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84>;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84>,
+ <MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84>;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004>,
+ <MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004>;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004>,
+ <MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004>;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004>,
+ <MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004>;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004>,
+ <MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004>;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14>;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14>;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94>,
+ <MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94>,
+ <MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94>,
+ <MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94>,
+ <MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94>,
+ <MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94>,
+ <MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94>;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16>,
+ <MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16>;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16>,
+ <MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16>;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16>,
+ <MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16>;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16>,
+ <MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16>;
+ };
+
+ pinctrl_usbotg1: usbotg1grp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84>,
+ <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84>;
+ };
+
+ pinctrl_usb1_extcon: usb1-extcongrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x1c0>;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84>;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
+ <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
+ <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
+ <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 000000000000..284e62acc0b4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,335 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+ compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ memory at 40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* identical to buck4_reg, but should never change */
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&gpu_2d {
+ status = "okay";
+};
+
+&gpu_3d {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom at 1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic at 25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM / VPU */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+
+ pcf85063: rtc at 51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom at 53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom at 57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82>,
+ <MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82>,
+ <MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82>;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004>,
+ <MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004>;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004>,
+ <MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004>;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94>;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84>;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6>,
+ <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
+ <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
+ <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
+ <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
+ <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
+ /* option USDHC3_RESET_B not defined, only in RM */
+ <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84>;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
new file mode 100644
index 000000000000..f27e3c8de916
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/* TQ-Systems GmbH MBa8Mx baseboard */
+
+/ {
+ beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm4 0 250000 0>;
+ beeper-hz = <4000>;
+ amp-supply = <®_vcc_3v3>;
+ };
+
+ chosen {
+ // bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
+ stdout-path = &uart3;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiobutton>;
+ autorepeat;
+
+ switch1 {
+ label = "switch1";
+ linux,code = <BTN_0>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ btn2: switch2 {
+ label = "switch2";
+ linux,code = <BTN_1>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ switch3 {
+ label = "switch3";
+ linux,code = <BTN_2>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ gpio_leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioled>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2: led2 {
+ label = "led2";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_hub_vbus: regulator-hub-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_HUB_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "SN65DSI83_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vcc_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "tqm-tlv320aic32";
+ ssi-controller = <&sai3>;
+ audio-codec = <&tlv320aic3x04>;
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vcc_3v3>;
+ fsl,magic-packet;
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at e {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0xe>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,dp83867-rxctrl-strap-quirk;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ enet-phy-lane-no-swap;
+ reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <500000>;
+ reset-deassert-us = <500>;
+ };
+ };
+};
+
+&i2c1 {
+ expander0: gpio at 23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ sd-mux-oe-hog {
+ gpio-hog;
+ gpios = <8 0>;
+ output-low;
+ line-name = "SD_MUX_EN#";
+ };
+
+ boot-cfg-oe-hog {
+ gpio-hog;
+ gpios = <12 0>;
+ output-high;
+ line-name = "BOOT_CFG_OE#";
+ };
+
+ rst-usb-hub-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ output-high;
+ line-name = "RST_USB_HUB#";
+ };
+ };
+
+ expander1: gpio at 24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ tlv320aic3x04: audio-codec at 18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
+ iov-supply = <®_vcc_3v3>;
+ ldoin-supply = <®_vcc_3v3>;
+ };
+
+ sensor1: sensor at 1f {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1f>;
+ };
+
+ eeprom3: eeprom at 57 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ #sound-dai-cells = <0>;
+ assigned-clock-rates = <49152000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+/* console */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+/* UART4 is assigned to Cortex-M4 */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-mmc;
+ no-sdio;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
--
2.25.1
More information about the linux-arm-kernel
mailing list