[RFC 0/5] arm64: imx8mm: Enable Hantro VPUs
Tim Harvey
tharvey at gateworks.com
Mon Nov 29 11:35:52 PST 2021
On Mon, Nov 29, 2021 at 10:59 AM Adam Ford <aford173 at gmail.com> wrote:
>
> On Mon, Nov 29, 2021 at 10:54 AM Ezequiel Garcia
> <ezequiel at vanguardiasur.com.ar> wrote:
> >
> > On Mon, 29 Nov 2021 at 13:48, Adam Ford <aford173 at gmail.com> wrote:
> > >
> > > On Tue, Nov 23, 2021 at 2:07 PM Nicolas Dufresne <nicolas at ndufresne.ca> wrote:
> > > >
> > > > Le lundi 22 novembre 2021 à 09:25 -0800, Tim Harvey a écrit :
> > > > > On Sat, Nov 20, 2021 at 7:36 AM Adam Ford <aford173 at gmail.com> wrote:
> > > > > >
> > > > > > On Fri, Nov 19, 2021 at 5:37 PM Adam Ford <aford173 at gmail.com> wrote:
> > > > > > >
> > > > > > > On Fri, Nov 19, 2021 at 10:29 AM Nicolas Dufresne <nicolas at ndufresne.ca> wrote:
> > > > > > > >
> > > > > > > > Hi Adam, Tim,
> > > > > > > >
> > > > > > > > [...]
> > > > > > > > > > > > Nicolas and Adam,
> > > > > > > > > > > >
> > > > > > > > > > > > For the H1 patches in this series: I've been able to test the IMX8MM
> > > > > > > > > > > > H1 JPEG encode using GStreamer 1.18.5:
> > > > > > > > > > > > $ gst-inspect-1.0 | grep -e "v4l2.*enc"
> > > > > > > > > > > > video4linux2: v4l2jpegenc: V4L2 JPEG Encoder
> > > > > > > > > > > > $ gst-launch-1.0 videotestsrc ! jpegenc ! rtpjpegpay ! udpsink
> > > > > > > > > > > ^ v4l2jpegenc
> > > > > > > > > > >
> > > > > > > > > > > This is just a transcript error ?
> > > > > > > > > >
> > > > > > > > > > Nicolas,
> > > > > > > > > >
> > > > > > > > > > No! Thanks for catching my mistake. I was testing with software encode... ooops!
> > > > > > > > > >
> > > > > > > > > > 'gst-launch-1.0 videotestsrc ! v4l2jpegenc ! fakesink' actually hangs
> > > > > > > > > > the board so likely a power-domain issue there?
> > > > > > > > >
> > > > > > > > > The v4l2-compliance tests fail on the h1 decoder with a hang, but I
> > > > > > > > > think we're writing to registers which are not documented in the Mini
> > > > > > > > > TRM. The Mini TRM doesn't explicitly show the JPEG encoding as a
> > > > > > > > > feature, but some of the registers state JPEG, but because some of the
> > > > > > > > > registers written for the H1 are not documented in the TRM. If those
> > > > > > > > > registers are restricted or not in this SoC, I am concerned that it
> > > > > > > > > might be related. I'll try to run some more tests this weekend to
> > > > > > > > > check on the status of the power-domain stuff.
> > > > > > > >
> > > > > > > > To verify if the HW support JPEG encoding you can read SWREG63 bit 25. This is
> > > > > > > > in the TRM, just not labelled properly. To mimic the decoding side, would be "HW
> > > > > > > > synthesis config register X" with the bit labelled SW_ENC_JPEG_PROF (but
> > > > > > > > PROF/profile is on or off). If your board hang while reading this, you likely
> > > > > > > > didn't get the power bit right.
> > > > > > > >
> > > > > > > > IMX8 has an undocumented control block thing that we have been fighting with in
> > > > > > > > imx8q, perhaps that's your issue. Few driver was proposed, we are still pending
> > > > > > > > on NXP solution to be submitted (they asked us to wait, still waiting =)).
> > > > > > >
> > > > > > > Nicolas,
> > > > > > >
> > > > > > > Thanks for the suggestion to read offset FC. There was an attempt
> > > > > > > made by Lucas Stach to develop a VPU blk-ctrl driver to coordinate the
> > > > > > > power-domains with the GPC driver. Unfortunately, it does appear to
> > > > > > > hang, so it might not be operating correctly.
> > > > > > >
> > > > > > > Lucas,
> > > > > > >
> > > > > > > Do you have any idea of stuff I can try to see if the power domain is
> > > > > > > coming online correctly?
> > > > > > >
> > > > > > > [ 10.434727] imx-pgc imx-pgc-domain.6: request the vpumix domain to power up
> > > > > > > [ 10.463647] imx-pgc imx-pgc-domain.6: request the vpumix ADB400 to power up
> > > > > > > [ 10.517155] imx-pgc imx-pgc-domain.6: genpd vpumix success
> > > > > > > [ 10.728927] vpu: set fuse bits to enable
> > > > > > > [ 10.825500] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-g1 GPC domain
> > > > > > > [ 10.878986] imx-pgc imx-pgc-domain.7: request the vpu-g1 domain to power up
> > > > > > > [ 10.932429] imx-pgc imx-pgc-domain.7: genpd vpu-g1 success
> > > > > > > [ 10.971988] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-g1 success
> > > > > > > [ 11.004726] hantro-vpu 38300000.video-codec: registered
> > > > > > > nxp,imx8mm-vpu-dec as /dev/video0
> > > > > > > [ 11.040760] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-g2 GPC domain
> > > > > > > [ 11.066181] imx-pgc imx-pgc-domain.8: request the vpu-g2 domain to power up
> > > > > > > [ 11.087887] imx-pgc imx-pgc-domain.8: genpd vpu-g2 success
> > > > > > > [ 11.113808] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-g2 success
> > > > > > > [ 11.139634] hantro-vpu 38310000.video-codec: registered
> > > > > > > nxp,imx8mm-vpu-g2-dec as /dev/video1
> > > > > > > [ 11.156463] imx8m-blk-ctrl 38330000.blk-ctrl: power vpublk-h1 GPC domain
> > > > > > > [ 11.170817] imx-pgc imx-pgc-domain.9: request the vpu-h1 domain to power up
> > > > > > > [ 11.232990] imx-pgc imx-pgc-domain.9: genpd vpu-h1 success
> > > > > > > [ 11.252546] imx8m-blk-ctrl 38330000.blk-ctrl: genpd vpublk-h1 success
> > > > > > > [ 11.266152] hantro-vpu 38320000.video-codec: Checking vpu->enc_base + 0xfc
> > > > > > >
> > > > > > > <hang>
> > > > > > >
> > > > > > > adam
> > > > > > >
> > > > > >
> > > > > > Nicolas, Tim, and Lucas,
> > > > > >
> > > > > > I think I have the hanging resolved in the power domains, and I'll be
> > > > > > pushing the fix to the GPCv2.
> > > > > >
> > > > > > For the H1 Encoder, I added some debugging code to read the offset
> > > > > > 0xfc and print some data based on the findings of that VPU-h1 offset.
> > > > > > I basically check the various bits per the TRM to see if they are set
> > > > > > and print some splat to indicate whether or not the function is
> > > > > > supported.
> > > > > >
> > > > > > [ 8.861865] hantro-vpu 38320000.video-codec: Checking vpu->enc_base + 0xfc
> > > > > > [ 8.870594] hantro-vpu 38320000.video-codec: Stabilization supported by HW
> > > > > > [ 8.889341] hantro-vpu 38320000.video-codec: VP8 encoding supported by HW
> > > > > > [ 8.899386] hantro-vpu 38320000.video-codec: H.264 encoding supported by HW
> > > > > > [ 8.918171] hantro-vpu 38320000.video-codec: RGB to YUV conversion
> > > > > > supported by HW
> > > > > > [ 8.934067] hantro-vpu 38320000.video-codec: registered
> > > > > > nxp,imx8mm-vpu-h1-enc as /dev/video2
> > > > > >
> > > > > > Unfortunately, JPEG is not listed as supported. :-(
> > > > >
> > > > > Adam,
> > > > >
> > > > > Well not having JPEG encode support is unfortunate, and unexpected. Do
> > > > > we not have hantro support yet for VP8/H264 encode?
> > > >
> > > > There is no mainline support yet. You can derive from RK3288 support using Google ChromeOS method (a v4l2 plugins that simulate in userspace a stateful encoder):
> > > >
> > > > - libv4l plugins / https://chromium.googlesource.com/chromiumos/third_party/libv4lplugins/+/refs/heads/master
> > > > - Kernel Driver / https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/media/platform/rockchip-vpu/
> > > >
> > > > >
> > > > > I haven't quite figured out how to build a modern mono-repo gstreamer
> > > > > on the ubuntu 20.04 rootfs I'm using so I haven't been able to test
> > > > > VPU encode/decode properly. I'll keep working on it when I'm back in
> > > > > the office the following week.
> > > >
> > > > Did a quick test to make sure there isn't any ubuntu specific blockers, here's a
> > > > dirty script that produce a minimal GStreamer, there was really nothing special
> > > > compare to other meson projects. Note that I use --wrap-mode=nofallback to avoid
> > > > letting GStreamer complete it's feature-set by downloading the planet. This
> > > > already build quite a lot and could likely be made smaller by avoid plugins-good
> > > > build-dep call, but then you need to check for v4l2odecs and video4linux devs
> > > > (mostly gudev a glib udev binding).
> > > >
> > > > # Install ubuntu
> > > > podman run -it --rm ubuntu:20.04
> > > > sed -i "s/# deb-src/deb-src/" /etc/apt/sources.list
> > > > apt update
> > > > apt build-dep gstreamer1.0-plugins-good
> > > > apt install git python3-pip flex bison
> > > >
> > > > # Need a newer meson
> > > > pip3 install --user meson
> > > > export PATH=$PATH:~/.local/bin
> > > >
> > > > # Build GStreamer
> > > > git clone https://gitlab.freedesktop.org/gstreamer/gstreamer.git
> > > > cd gstreamer
> > > > meson setup build --wrap-mode=nofallback
> > > > ninja -C build
> > > >
> > > > # Run in-place
> > > > ./gst-env.py
> > > > gst-inspect-1.0 v4l2codecs
> > > > gst-inspect 1.0 video4linux2
> > > >
> > > Thanks for the suggestions.
> > >
> > > I downloaded what's in the master repo:
> > >
> > > [gst-main] root at localhost:~/gstreamer# gst-inspect-1.0 v4l2codecs
> > >
> > > ** (gst-plugin-scanner:7317): CRITICAL **: 10:29:51.847: can't find
> > > gi.repository.Gst
> > > Plugin Details:
> > > Name v4l2codecs
> > > Description V4L2 CODEC Accelerators plugin
> > > Filename
> > > /root/gstreamer/builddir/subprojects/gst-plugins-bad/sys/v4l2codecs/libgstv4l2codecs.so
> > > Version 1.19.3.1
> > > License LGPL
> > > Source module gst-plugins-bad
> > > Binary package GStreamer Bad Plug-ins git
> > > Origin URL Unknown package origin
> > >
> > > v4l2slh264dec: V4L2 Stateless H.264 Video Decoder
> > > v4l2slmpeg2dec: V4L2 Stateless Mpeg2 Video Decoder
> > > v4l2slvp8alphadecodebin: VP8 Alpha Decoder
> > > v4l2slvp8dec: V4L2 Stateless VP8 Video Decoder
> > >
> > > 4 features:
> > > +-- 4 elements
> > >
> > > [gst-main] root at localhost:~/gstreamer# gst-inspect-1.0 video4linux2
> > > Plugin Details:
> > > Name video4linux2
> > > Description elements for Video 4 Linux
> > > Filename
> > > /root/gstreamer/builddir/subprojects/gst-plugins-good/sys/v4l2/libgstvideo4linux2.so
> > > Version 1.19.3.1
> > > License LGPL
> > > Source module gst-plugins-good
> > > Binary package GStreamer Good Plug-ins git
> > > Origin URL Unknown package origin
> > >
> > > v4l2deviceprovider: Video (video4linux2) Device Provider
> > > v4l2jpegenc: V4L2 JPEG Encoder
> > > v4l2radio: Radio (video4linux2) Tuner
> > > v4l2sink: Video (video4linux2) Sink
> > > v4l2src: Video (video4linux2) Source
> > >
> > > 5 features:
> > > +-- 4 elements
> > > +-- 1 device providers
> > >
> > > I still have the H1 encoder enabled, but I know JPEG isn't supported,
> > > so I'm going to attempt to do some decoding and pipe to fakesink since
> > > I don't have a functional display yet.
> > >
> > > gst-launch-1.0 -ev filesrc location=trailer_1080p_h264_mp3.avi !
> > > decodebin3 ! fakesink
> > >
> > > Redistribute latency...
> > > /GstPipeline:pipeline0/GstDecodebin3:decodebin3-0/v4l2slh264dec:v4l2slh264dec0.GstPad:src:
> > > caps = video/x-raw, format=(string)NV12, width=(int)1920,
> > > height=(int)1080, interlace-mode=(string)progressive,
> > > multiview-mode=(string)mono,
> > > multiview-flags=(GstVideoMultiviewFlagsSet)0:ffffffff:/right-view-first/left-flipped/left-flopped/right-flipped/right-flopped/half-aspect/mixed-mono,
> > > pixel-aspect-ratio=(fraction)1/1, framerate=(fraction)25/1
> > > /GstPipeline:pipeline0/GstDecodebin3:decodebin3-0.GstGhostPad:video_0:
> > > caps = video/x-raw, format=(string)NV12, width=(int)1920,
> > > height=(int)1080, interlace-mode=(string)progressive,
> > > multiview-mode=(string)mono,
> > > multiview-flags=(GstVideoMultiviewFlagsSet)0:ffffffff:/right-view-first/left-flipped/left-flopped/right-flipped/right-flopped/half-aspect/mixed-mono,
> > > pixel-aspect-ratio=(fraction)1/1, framerate=(fraction)25/1
> > > /GstPipeline:pipeline0/GstDecodebin3:decodebin3-0.GstGhostPad:video_0.GstProxyPad:proxypad6:
> > > caps = video/x-raw, format=(string)NV12, width=(int)1920,
> > > height=(int)1080, interlace-mode=(string)progressive,
> > > multiview-mode=(string)mono,
> > > multiview-flags=(GstVideoMultiviewFlagsSet)0:ffffffff:/right-view-first/left-flipped/left-flopped/right-flipped/right-flopped/half-aspect/mixed-mono,
> > > pixel-aspect-ratio=(fraction)1/1, framerate=(fraction)25/1
> > > /GstPipeline:pipeline0/GstDecodebin3:decodebin3-0/GstMultiQueue:multiqueue0:
> > > min-interleave-time = 300000000
> > > Redistribute latency...
> > > /GstPipeline:pipeline0/GstDecodebin3:decodebin3-0/v4l2slh264dec:v4l2slh264dec0.GstPad:sink:
> > > caps = video/x-h264, variant=(string)itu, framerate=(fraction)25/1,
> > > width=(int)1920, height=(int)1080, chroma-format=(string)4:2:0,
> > > bit-depth-luma=(uint)8, bit-depth-chroma=(uint)8,
> > > parsed=(boolean)true, stream-format=(string)avc, alignment=(string)au,
> > > profile=(string)high, level=(string)4,
> > > codec_data=(buffer)01640028ffe1001a67640028acd940780227e584000003000400000300c83c60c65801000668ebe3cb22c0
> > > New clock: GstSystemClock
> > >
> > > And it appears to stream, because the counter increases. I haven't
> > > checked the CPU utilization, but the fact that it shows v4l2slh264dec
> > > is good.
> > >
> > > Is there a way to know if/how the decoder is using the proper VPU? I
> > > assume if it wasn't using the proper one, it would fail, but was just
> > > curious.
> > >
> >
> > A few ways. You can check /proc/interrupts, which should have
> > VPU activity.
> >
> > Or enable debug messages for the module,
> > using the debug hantro parameter. V4L2 has debug messages
> > that you can enable, see /sys/class/video4linux/video0/dev_debug.
> >
> > Instead of fakesink you can output to pngenc/jpegenc and check the output
> > is visually correct. If at all possible, the proper way is to use Fluster,
> > and report the score you get:
> >
> > https://github.com/fluendo/fluster
> >
>
> I ran fluster on the VP8 decoder, but only 55/61 passed.
>
> ****************************************************************************************************
> Running test suite VP8-TEST-VECTORS with decoder GStreamer-VP8-V4L2SL-Gst1.0
> Using 4 parallel job(s)
> ****************************************************************************************************
>
> [TEST SUITE ] (DECODER ) TEST VECTOR
> ... RESULT
> ----------------------------------------------------------------------
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-004 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-001 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-002 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-003 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-005 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-006 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-007 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-008 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-011 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-009 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-012 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-013 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-014 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-010 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-016 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-017 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-018 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-01-intra-1400
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-01-intra-1416
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-01-intra-1417
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-01-intra-1411
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-02-inter-1402
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-02-inter-1412
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-02-inter-1424
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-01 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-02 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-03 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-04 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1401 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0) vp80-02-inter-1418
> ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1403 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1407 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1408 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1409 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1413 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1415 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1425 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1426 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1427 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1432 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1435 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1436 ... Fail
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-00-comprehensive-015 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1441 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1437 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-04-partitions-1404 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1442 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-04-partitions-1405 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-04-partitions-1406 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1428 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1429 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1431 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1410 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-03-segmentation-1414 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1430 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1433 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1438 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1434 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1439 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1440 ... Success
> [VP8-TEST-VECTORS] (GStreamer-VP8-V4L2SL-Gst1.0)
> vp80-05-sharpness-1443 ... Success
>
>
> =======================================================================
> FAIL: vp80-03-segmentation-01 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: 'db954c077b7a3f34a448ceaacf8f525c' !=
> '8bbb396a9bdf8afa250d3b2e45e6b367'
> - db954c077b7a3f34a448ceaacf8f525c
> + 8bbb396a9bdf8afa250d3b2e45e6b367
> : vp80-03-segmentation-01
>
> =======================================================================
> FAIL: vp80-03-segmentation-02 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: '4d2d65efeee1c83772c33a13446bd1a4' !=
> '1b2061d4a74549228769f8e292bcb15f'
> - 4d2d65efeee1c83772c33a13446bd1a4
> + 1b2061d4a74549228769f8e292bcb15f
> : vp80-03-segmentation-02
>
> =======================================================================
> FAIL: vp80-03-segmentation-03 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: '73d864433691f8db43257b88495ac8c3' !=
> 'fd1eb6ebd7100995bad11042a9bea048'
> - 73d864433691f8db43257b88495ac8c3
> + fd1eb6ebd7100995bad11042a9bea048
> : vp80-03-segmentation-03
>
> =======================================================================
> FAIL: vp80-03-segmentation-04 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: '7f846c8bd7cdfe61f8542f382f9d8eeb' !=
> '0c27a47c4fd8bbfce173d005bef8be6a'
> - 7f846c8bd7cdfe61f8542f382f9d8eeb
> + 0c27a47c4fd8bbfce173d005bef8be6a
> : vp80-03-segmentation-04
>
> =======================================================================
> FAIL: vp80-03-segmentation-1425 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: '96ffacf0c3eae59b58252be24a60e9b2' !=
> '83e8a322e8ab23e60ba16430aacad827'
> - 96ffacf0c3eae59b58252be24a60e9b2
> + 83e8a322e8ab23e60ba16430aacad827
> : vp80-03-segmentation-1425
>
> =======================================================================
> FAIL: vp80-03-segmentation-1436 (GStreamer-VP8-V4L2SL-Gst1.0.VP8-TEST-VECTORS)
> ----------------------------------------------------------------------
> Traceback (most recent call last):
> File "/root/gstreamer/fluster/fluster/test.py", line 104, in _test
> self.assertEqual(
> AssertionError: 'bfd17a557ee1ba347c755a18ce5a64a6' !=
> '5bca61a733c1936205f82de1492a1b2b'
> - bfd17a557ee1ba347c755a18ce5a64a6
> + 5bca61a733c1936205f82de1492a1b2b
> : vp80-03-segmentation-1436
>
> Ran 55/61 tests successfully in 12.104 secs
>
> I am not that familiar with this tool, but I assume failures are bad.
> However these look like Python errors and not gst errors.
>
> The H264 decoder resulted in:
>
> Ran 85/135 tests successfully in 57.821 secs
>
> I can provide the splat if you want. Those looked like gst errors,
> because most of the error messages state the gst-launch-1.0 returned
> non-zero exit status 1.
>
>
> > It should be easy to use.
>
> It was.
> >
> > > I think I'll redo the patch without the RFC and without the H1 encoder
> > > unless anyone has any objections. I know I need to rebase on
> > > linux-next anyway because the patches don't apply cleanly. Is there a
> > > specific branch I should use? I don't know if this goes through
> > > Shawn's IMX tree or the media tree (or a combination)
> > >
> >
> > You should rebase on media's master branch:
> >
> > https://git.linuxtv.org/media_tree.git/log/
>
> I'll submit the patch with a cover letter with the results of the VP8
> and H264 fluster test in the cover letter. Is there a stateless
> decoder for the VP9 decoder? gst-inspect only shows the following
> v4l2codecs.
>
> v4l2slh264dec: V4L2 Stateless H.264 Video Decoder
> v4l2slmpeg2dec: V4L2 Stateless Mpeg2 Video Decoder
> v4l2slvp8alphadecodebin: VP8 Alpha Decoder
> v4l2slvp8dec: V4L2 Stateless VP8 Video Decoder
>
> thanks for all your help. Hopefully we can get this integrated soon.
>
Adam,
What deps did you install in order to get v4l2codecs building? I
installed libgudev-1.0-dev based on Nicolas' suggestion and rebuilt
(not sure if I needed to re-configure somehow) but there is still
nothing in build/subprojects/gst-plugins-bad/sys/v4l2codecs/. A 'meson
configure' tells me that v4l2codecs is set to 'auto' but I'm not sure
how to find out what dependencies are needed or what may be missing.
Best regards,
Tim
More information about the linux-arm-kernel
mailing list