[PATCH v7 2/3] arm64: dts: mediatek: add basic mt7986a support
Sam Shih
sam.shih at mediatek.com
Wed Nov 17 19:48:46 PST 2021
Hi
On Tue, 2021-11-16 at 12:18 +0100, Matthias Brugger wrote:
>
> On 16/11/2021 02:39, Sam Shih wrote:
> > Hi,
> >
> > On Mon, 2021-11-15 at 17:27 +0100, Matthias Brugger wrote:
> > > Hi,
> > >
> > > On 18/10/2021 13:40, Sam Shih wrote:
> > > > Add basic chip support for Mediatek mt7986a, include
> > > > basic uart nodes, rng node and watchdog node.
> > > >
> > > > Add cpu node, timer node, gic node, psci and reserved-memory
> > > > node
> > > > for ARM Trusted Firmware.
> > > >
> > >
> > > What is the exact difference between mt7986a and mt7986b? Right
> > > now,
> > > it's only
> > > the compatible, for that it makes no sense to split them.
> > >
> >
> > The difference between mt7986a and mt7986b is pinout which
> > described
> > in our pinctrl patch series
> >
https://urldefense.com/v3/__https://lore.kernel.org/all/20211022124036.5291-3-sam.shih@mediatek.com/__;!!CTRNKA9wMg0ARbw!0kseU8x1KnHHXDErh6Yj6MKqecufPEfGyeumtTBism47e99UFO2Gs-HfWjL1_jUv$
> >
> >
> > You are right, in this "basic SoC support" patch series, only show
> > compatible differences
> >
> > > It would be good to see what the exact differences are, so that
> > > we
> > > can see if it
> > > makes sense to have one of the alternatives:
> > > 1) use a common mt7986.dtsi which get included by
> > > mt7986[a,b].dtsi
> > > 2) Use on mt7986.dtsi and only add one mt7986a.dtsi or
> > > mt7986b.dtsi
> > > which has
> > > add-ons.
> > >
> >
> > In this case, can we use solution (1) to create a generic
> > mt7986.dtsi
> > in this patch series, and add mt7986[a,b].dtsi to the dts part of
> > the
> > pinctrl patch series to separate the difference nodes?
> >
>
> If the only difference is the GPIO controller then why not go with
> solution 2.
> Create a mt7986.dtsi which holds e.g. the node for pincontroller
> mt7986a and
> then create a mt7986b.dtsi that just changes compatible and gpio-
> ranges:
>
> &pio {
> compatible = "mediatek,mt7986b-pinctrl";
> gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
> }
>
> What do you think?
Ok,
For this basic patch series DTS, I will send the next version:
- Use "mt7986.dtsi" instead of "mt7986[a,b].dtsi",
And make"mt7986.dtsi" get included by "mt7986[a,b]-rfb.dts"
(No dedicated uart1/uart2 pinout for mt7986b-rfb, status of dts node
shoud be set to "disabled")
For the pinctrl patch series DTS, I will send th next version:
- Add "mt7986b.dtsi" according to your suggestion,
the new include
chain will be:
mt7986a-rfb.dts <-- mt7986.dtsi (mt7986a pinctrl)
mt7986b-rfb.dts <-- mt7986b.dtsi (mt7986b pinctrl) <-- mt7986.dtsi
(mt7986a pinctrl)
Do you agree above proposal?
Regards,
Sam
>
> Regards,
> Matthias
>
> > > > Signed-off-by: Sam Shih <sam.shih at mediatek.com>
> > > >
> > > > ---
> > > > v7: added memory node back to dts
> > > > v6: removed clock and pinctrl node, to separate basic part into
> > > > a
> > > > single
> > > > patch series
> > > >
> > > > Original thread:
> > > >
> >
> >
https://urldefense.com/v3/__https://lore.kernel.org/all/20211004124155.1404-1-sam.shih@mediatek.com/__;!!CTRNKA9wMg0ARbw!xCEW0lwTKx4k272sWASoi90y_yRyQdAx0oNJC-jSAIWnIEkprJD-gAc1ugCvo0ex$
> > > >
> > > >
> > > > v5: follow reviewr's comment: removed clock freqency node in
> > > > timer
> > > > due to
> > > > we have set CNTFRQ_EL0 in ATF firmware, and also
> > > > corrected
> > > > GICD range
> > > > v4: added missing gic register bases, and fixed range of GICR
> > > > v3: used the stdout-path instead of console=ttyS0
> > > > v2: modified clock and uart node due to clock driver updated
> > > > ---
> > > > arch/arm64/boot/dts/mediatek/Makefile | 1 +
> > > > arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 38 +++++
> > > > arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 149
> > > > +++++++++++++++++++
> > > > 3 files changed, 188 insertions(+)
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-
> > > > rfb.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > > >
> > > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile
> > > > b/arch/arm64/boot/dts/mediatek/Makefile
> > > > index 4f68ebed2e31..e6c3a73b9e4a 100644
> > > > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > > > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > > > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > > > b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > > > new file mode 100644
> > > > index 000000000000..ca074cf8e578
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > > > @@ -0,0 +1,38 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright (C) 2021 MediaTek Inc.
> > > > + * Author: Sam.Shih <sam.shih at mediatek.com>
> > > > + */
> > > > +
> > > > +/dts-v1/;
> > > > +#include "mt7986a.dtsi"
> > > > +
> > > > +/ {
> > > > + model = "MediaTek MT7986a RFB";
> > > > + compatible = "mediatek,mt7986a-rfb";
> > > > +
> > > > + aliases {
> > > > + serial0 = &uart0;
> > > > + };
> > > > +
> > > > + chosen {
> > > > + stdout-path = "serial0:115200n8";
> > > > + bootargs = "earlycon=uart8250,mmio32,0x11002000
> > > > swiotlb=512";
> > >
> > > We normally don't add earlycon parameter to the normal bootargs,
> > > as
> > > it's only
> > > for debugging. Also what do we need the swiotlb? Are there any
> > > limitation in the
> > > HW that makes us need it?
> > >
> >
> > Thank you for your suggestion, as far as I know, it should not have
> > hardware limitations. This bootargs is just inherent from mt7622-
> > rfb.dts, I will delete it and test again on our development board.
> >
> > > Regards,
> > > Matthias
> > >
> > > > + };
> > > > +
> > > > + memory {
> > > > + reg = <0 0x40000000 0 0x40000000>;
> > > > + };
> > > > +};
> > > > +
> > > > +&uart0 {
> > > > + status = "okay";
> > > > +};
> > > > +
> > > > +&uart1 {
> > > > + status = "okay";
> > > > +};
> > > > +
> > > > +&uart2 {
> > > > + status = "okay";
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > > > b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > > > new file mode 100644
> > > > index 000000000000..75912bcf6c9c
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > > > @@ -0,0 +1,149 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright (C) 2021 MediaTek Inc.
> > > > + * Author: Sam.Shih <sam.shih at mediatek.com>
> > > > + */
> > > > +
> > > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > > > +
> > > > +/ {
> > > > + compatible = "mediatek,mt7986a";
> > > > + interrupt-parent = <&gic>;
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > +
> > > > + system_clk: dummy40m {
> > > > + compatible = "fixed-clock";
> > > > + clock-frequency = <40000000>;
> > > > + #clock-cells = <0>;
> > > > + };
> > > > +
> > > > + cpus {
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > + cpu0: cpu at 0 {
> > > > + device_type = "cpu";
> > > > + compatible = "arm,cortex-a53";
> > > > + enable-method = "psci";
> > > > + reg = <0x0>;
> > > > + #cooling-cells = <2>;
> > > > + };
> > > > +
> > > > + cpu1: cpu at 1 {
> > > > + device_type = "cpu";
> > > > + compatible = "arm,cortex-a53";
> > > > + enable-method = "psci";
> > > > + reg = <0x1>;
> > > > + #cooling-cells = <2>;
> > > > + };
> > > > +
> > > > + cpu2: cpu at 2 {
> > > > + device_type = "cpu";
> > > > + compatible = "arm,cortex-a53";
> > > > + enable-method = "psci";
> > > > + reg = <0x2>;
> > > > + #cooling-cells = <2>;
> > > > + };
> > > > +
> > > > + cpu3: cpu at 3 {
> > > > + device_type = "cpu";
> > > > + enable-method = "psci";
> > > > + compatible = "arm,cortex-a53";
> > > > + reg = <0x3>;
> > > > + #cooling-cells = <2>;
> > > > + };
> > > > + };
> > > > +
> > > > + psci {
> > > > + compatible = "arm,psci-0.2";
> > > > + method = "smc";
> > > > + };
> > > > +
> > > > + reserved-memory {
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > + ranges;
> > > > + /* 192 KiB reserved for ARM Trusted Firmware
> > > > (BL31) */
> > > > + secmon_reserved: secmon at 43000000 {
> > > > + reg = <0 0x43000000 0 0x30000>;
> > > > + no-map;
> > > > + };
> > > > + };
> > > > +
> > > > + timer {
> > > > + compatible = "arm,armv8-timer";
> > > > + interrupt-parent = <&gic>;
> > > > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> > > > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> > > > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> > > > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> > > > + };
> > > > +
> > > > + soc {
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > + compatible = "simple-bus";
> > > > + ranges;
> > > > +
> > > > + gic: interrupt-controller at c000000 {
> > > > + compatible = "arm,gic-v3";
> > > > + #interrupt-cells = <3>;
> > > > + interrupt-parent = <&gic>;
> > > > + interrupt-controller;
> > > > + reg = <0 0x0c000000 0 0x10000>, /*
> > > > GICD */
> > > > + <0 0x0c080000 0 0x80000>, /*
> > > > GICR */
> > > > + <0 0x0c400000 0 0x2000>, /*
> > > > GICC */
> > > > + <0 0x0c410000 0 0x1000>, /*
> > > > GICH */
> > > > + <0 0x0c420000 0 0x2000>; /*
> > > > GICV */
> > > > + interrupts = <GIC_PPI 9
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + };
> > > > +
> > > > + watchdog: watchdog at 1001c000 {
> > > > + compatible = "mediatek,mt7986-wdt",
> > > > + "mediatek,mt6589-wdt";
> > > > + reg = <0 0x1001c000 0 0x1000>;
> > > > + interrupts = <GIC_SPI 110
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + #reset-cells = <1>;
> > > > + status = "disabled";
> > > > + };
> > > > +
> > > > + trng: trng at 1020f000 {
> > > > + compatible = "mediatek,mt7986-rng",
> > > > + "mediatek,mt7623-rng";
> > > > + reg = <0 0x1020f000 0 0x100>;
> > > > + clocks = <&system_clk>;
> > > > + clock-names = "rng";
> > > > + status = "disabled";
> > > > + };
> > > > +
> > > > + uart0: serial at 11002000 {
> > > > + compatible = "mediatek,mt7986-uart",
> > > > + "mediatek,mt6577-uart";
> > > > + reg = <0 0x11002000 0 0x400>;
> > > > + interrupts = <GIC_SPI 123
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + clocks = <&system_clk>;
> > > > + status = "disabled";
> > > > + };
> > > > +
> > > > + uart1: serial at 11003000 {
> > > > + compatible = "mediatek,mt7986-uart",
> > > > + "mediatek,mt6577-uart";
> > > > + reg = <0 0x11003000 0 0x400>;
> > > > + interrupts = <GIC_SPI 124
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + clocks = <&system_clk>;
> > > > + status = "disabled";
> > > > + };
> > > > +
> > > > + uart2: serial at 11004000 {
> > > > + compatible = "mediatek,mt7986-uart",
> > > > + "mediatek,mt6577-uart";
> > > > + reg = <0 0x11004000 0 0x400>;
> > > > + interrupts = <GIC_SPI 125
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + clocks = <&system_clk>;
> > > > + status = "disabled";
> > > > + };
> > > > +
> > > > + };
> > > > +
> > > > +};
> > > >
> >
> > Regards,
> > Sam
> >
More information about the linux-arm-kernel
mailing list