[PATCH net-next v2 04/10] net: sparx5: add port module support
Steen Hegelund
steen.hegelund at microchip.com
Fri May 28 05:34:13 PDT 2021
This add configuration of the Sparx5 port module instances.
Sparx5 has in total 65 logical ports (denoted D0 to D64) and 33
physical SerDes connections (S0 to S32). The 65th port (D64) is fixed
allocated to SerDes0 (S0). The remaining 64 ports can in various
multiplexing scenarios be connected to the remaining 32 SerDes using
QSGMII, or USGMII or USXGMII extenders. 32 of the ports can have a 1:1
mapping to the 32 SerDes.
Some additional ports (D65 to D69) are internal to the device and do not
connect to port modules or SerDes macros. For example, internal ports are
used for frame injection and extraction to the CPU queues.
The 65 logical ports are split up into the following blocks.
- 13 x 5G ports (D0-D11, D64)
- 32 x 2G5 ports (D16-D47)
- 12 x 10G ports (D12-D15, D48-D55)
- 8 x 25G ports (D56-D63)
Each logical port supports different line speeds, and depending on the
speeds supported, different port modules (MAC+PCS) are needed. A port
supporting 5 Gbps, 10 Gbps, or 25 Gbps as maximum line speed, will have a
DEV5G, DEV10G, or DEV25G module to support the 5 Gbps, 10 Gbps (incl 5
Gbps), or 25 Gbps (including 10 Gbps and 5 Gbps) speeds. As well as, it
will have a shadow DEV2G5 port module to support the lower speeds
(10/100/1000/2500Mbps). When a port needs to operate at lower speed and the
shadow DEV2G5 needs to be connected to its corresponding SerDes
Not all interface modes are supported in this series, but will be added at
a later stage.
Signed-off-by: Steen Hegelund <steen.hegelund at microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson at microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen at microchip.com>
---
.../net/ethernet/microchip/sparx5/Makefile | 3 +-
.../ethernet/microchip/sparx5/sparx5_main.c | 21 +-
.../ethernet/microchip/sparx5/sparx5_netdev.c | 14 +-
.../microchip/sparx5/sparx5_phylink.c | 37 +-
.../ethernet/microchip/sparx5/sparx5_port.c | 1129 +++++++++++++++++
.../ethernet/microchip/sparx5/sparx5_port.h | 98 ++
6 files changed, 1292 insertions(+), 10 deletions(-)
create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_port.c
create mode 100644 drivers/net/ethernet/microchip/sparx5/sparx5_port.h
diff --git a/drivers/net/ethernet/microchip/sparx5/Makefile b/drivers/net/ethernet/microchip/sparx5/Makefile
index 19a593d17f4a..9c14eec33fd7 100644
--- a/drivers/net/ethernet/microchip/sparx5/Makefile
+++ b/drivers/net/ethernet/microchip/sparx5/Makefile
@@ -5,4 +5,5 @@
obj-$(CONFIG_SPARX5_SWITCH) += sparx5-switch.o
-sparx5-switch-objs := sparx5_main.o sparx5_packet.o sparx5_netdev.o sparx5_phylink.o
+sparx5-switch-objs := sparx5_main.o sparx5_packet.o \
+ sparx5_netdev.o sparx5_port.o sparx5_phylink.o
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
index 68fd0d5353ba..0ae8320a5bbb 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
@@ -26,6 +26,7 @@
#include "sparx5_main_regs.h"
#include "sparx5_main.h"
+#include "sparx5_port.h"
#define QLIM_WM(fraction) \
((SPX5_BUFFER_MEMORY / SPX5_BUFFER_CELL_SZ - 100) * (fraction) / 100)
@@ -252,6 +253,7 @@ static int sparx5_create_port(struct sparx5 *sparx5,
struct sparx5_port *spx5_port;
struct net_device *ndev;
struct phylink *phylink;
+ int err;
ndev = sparx5_create_netdev(sparx5, config->portno);
if (IS_ERR(ndev)) {
@@ -271,9 +273,26 @@ static int sparx5_create_port(struct sparx5 *sparx5,
spx5_port->custom_etype = 0x8880; /* Vitesse */
sparx5->ports[config->portno] = spx5_port;
+ err = sparx5_port_init(sparx5, spx5_port, &config->conf);
+ if (err) {
+ dev_err(sparx5->dev, "port init failed\n");
+ return err;
+ }
spx5_port->conf = config->conf;
- /* VLAN setup to be added in later patches */
+ /* VLAN support to be added in later patches */
+
+ /* Create a phylink for PHY management. Also handles SFPs */
+ spx5_port->phylink_config.dev = &spx5_port->ndev->dev;
+ spx5_port->phylink_config.type = PHYLINK_NETDEV;
+ spx5_port->phylink_config.pcs_poll = true;
+
+ phylink = phylink_create(&spx5_port->phylink_config,
+ of_fwnode_handle(config->node),
+ config->conf.phy_mode,
+ &sparx5_phylink_mac_ops);
+ if (IS_ERR(phylink))
+ return PTR_ERR(phylink);
/* Create a phylink for PHY management. Also handles SFPs */
spx5_port->phylink_config.dev = &spx5_port->ndev->dev;
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c b/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
index 10fdea8d3400..38cca57bdd1e 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_netdev.c
@@ -6,6 +6,7 @@
#include "sparx5_main_regs.h"
#include "sparx5_main.h"
+#include "sparx5_port.h"
/* The IFH bit position of the first VSTAX bit. This is because the
* VSTAX bit positions in Data sheet is starting from zero.
@@ -71,6 +72,7 @@ static int sparx5_port_open(struct net_device *ndev)
struct sparx5_port *port = netdev_priv(ndev);
int err = 0;
+ sparx5_port_enable(port, true);
err = phylink_of_phy_connect(port->phylink, port->of_node, 0);
if (err) {
netdev_err(ndev, "Could not attach to PHY\n");
@@ -82,7 +84,10 @@ static int sparx5_port_open(struct net_device *ndev)
if (!ndev->phydev) {
/* power up serdes */
port->conf.power_down = false;
- err = phy_power_on(port->serdes);
+ if (port->conf.serdes_reset)
+ err = sparx5_serdes_set(port->sparx5, port, &port->conf);
+ else
+ err = phy_power_on(port->serdes);
if (err)
netdev_err(ndev, "%s failed\n", __func__);
}
@@ -95,12 +100,17 @@ static int sparx5_port_stop(struct net_device *ndev)
struct sparx5_port *port = netdev_priv(ndev);
int err = 0;
+ sparx5_port_enable(port, false);
phylink_stop(port->phylink);
phylink_disconnect_phy(port->phylink);
if (!ndev->phydev) {
+ /* power down serdes */
port->conf.power_down = true;
- err = phy_power_off(port->serdes);
+ if (port->conf.serdes_reset)
+ err = sparx5_serdes_set(port->sparx5, port, &port->conf);
+ else
+ err = phy_power_off(port->serdes);
if (err)
netdev_err(ndev, "%s failed\n", __func__);
}
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c b/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
index 3f0155b05c1e..6f8eb456e93f 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
@@ -12,6 +12,7 @@
#include "sparx5_main_regs.h"
#include "sparx5_main.h"
+#include "sparx5_port.h"
static void sparx5_phylink_validate(struct phylink_config *config,
unsigned long *supported,
@@ -94,6 +95,7 @@ static void sparx5_phylink_mac_config(struct phylink_config *config,
{
struct sparx5_port *port = netdev_priv(to_net_dev(config->dev));
struct sparx5_port_config conf;
+ int err = 0;
conf = port->conf;
conf.power_down = false;
@@ -126,6 +128,11 @@ static void sparx5_phylink_mac_config(struct phylink_config *config,
if (!port_conf_has_changed(&port->conf, &conf))
return;
+
+ /* Enable the PCS matching this interface type */
+ err = sparx5_port_pcs_set(port->sparx5, port, &conf);
+ if (err)
+ netdev_err(port->ndev, "port config failed: %d\n", err);
}
static void sparx5_phylink_mac_link_up(struct phylink_config *config,
@@ -135,17 +142,35 @@ static void sparx5_phylink_mac_link_up(struct phylink_config *config,
int speed, int duplex,
bool tx_pause, bool rx_pause)
{
- /* Currently not used */
+ struct sparx5_port *port = netdev_priv(to_net_dev(config->dev));
+ struct sparx5_port_config conf;
+ int err = 0;
+
+ conf = port->conf;
+ conf.duplex = duplex;
+ conf.pause = 0;
+ conf.pause |= tx_pause ? MLO_PAUSE_TX : 0;
+ conf.pause |= rx_pause ? MLO_PAUSE_RX : 0;
+ conf.speed = speed;
+
+ /* Configure the port to speed/duplex/pause */
+ err = sparx5_port_config(port->sparx5, port, &conf);
+ if (err)
+ netdev_err(port->ndev, "port config failed: %d\n", err);
}
static void sparx5_phylink_mac_link_state(struct phylink_config *config,
struct phylink_link_state *state)
{
- state->link = true;
- state->an_complete = true;
- state->speed = SPEED_1000;
- state->duplex = true;
- state->pause = MLO_PAUSE_AN;
+ struct sparx5_port *port = netdev_priv(to_net_dev(config->dev));
+ struct sparx5_port_status status;
+
+ sparx5_get_port_status(port->sparx5, port, &status);
+ state->link = status.link && !status.link_down;
+ state->an_complete = status.an_complete;
+ state->speed = status.speed;
+ state->duplex = status.duplex;
+ state->pause = status.pause;
}
static void sparx5_phylink_mac_aneg_restart(struct phylink_config *config)
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
new file mode 100644
index 000000000000..21c7d14d050c
--- /dev/null
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -0,0 +1,1129 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Microchip Sparx5 Switch driver
+ *
+ * Copyright (c) 2021 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+
+#include "sparx5_main_regs.h"
+#include "sparx5_main.h"
+#include "sparx5_port.h"
+
+#define SPX5_ETYPE_TAG_C 0x8100
+#define SPX5_ETYPE_TAG_S 0x88a8
+
+#define SPX5_WAIT_US 1000
+#define SPX5_WAIT_MAX_US 2000
+
+enum port_error {
+ SPX5_PERR_SPEED,
+ SPX5_PERR_IFTYPE,
+};
+
+#define PAUSE_DISCARD 0xC
+#define ETH_MAXLEN (ETH_DATA_LEN + ETH_HLEN + ETH_FCS_LEN)
+
+static void decode_sgmii_word(u16 lp_abil, struct sparx5_port_status *status)
+{
+ status->an_complete = true;
+ if (!(lp_abil & LPA_SGMII_LINK)) {
+ status->link = false;
+ return;
+ }
+
+ switch (lp_abil & LPA_SGMII_SPD_MASK) {
+ case LPA_SGMII_10:
+ status->speed = SPEED_10;
+ break;
+ case LPA_SGMII_100:
+ status->speed = SPEED_100;
+ break;
+ case LPA_SGMII_1000:
+ status->speed = SPEED_1000;
+ break;
+ default:
+ status->link = false;
+ return;
+ }
+ if (lp_abil & LPA_SGMII_FULL_DUPLEX)
+ status->duplex = DUPLEX_FULL;
+ else
+ status->duplex = DUPLEX_HALF;
+}
+
+static void decode_cl37_word(u16 lp_abil, uint16_t ld_abil, struct sparx5_port_status *status)
+{
+ status->link = !(lp_abil & ADVERTISE_RFAULT) && status->link;
+ status->an_complete = true;
+ status->duplex = (ADVERTISE_1000XFULL & lp_abil) ?
+ DUPLEX_FULL : DUPLEX_UNKNOWN; // 1G HDX not supported
+
+ if ((ld_abil & ADVERTISE_1000XPAUSE) &&
+ (lp_abil & ADVERTISE_1000XPAUSE)) {
+ status->pause = MLO_PAUSE_RX | MLO_PAUSE_TX;
+ } else if ((ld_abil & ADVERTISE_1000XPSE_ASYM) &&
+ (lp_abil & ADVERTISE_1000XPSE_ASYM)) {
+ status->pause |= (lp_abil & ADVERTISE_1000XPAUSE) ?
+ MLO_PAUSE_TX : 0;
+ status->pause |= (ld_abil & ADVERTISE_1000XPAUSE) ?
+ MLO_PAUSE_RX : 0;
+ } else {
+ status->pause = MLO_PAUSE_NONE;
+ }
+}
+
+static int sparx5_get_dev2g5_status(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_status *status)
+{
+ u32 portno = port->portno;
+ u16 lp_adv, ld_adv;
+ u32 value;
+
+ /* Get PCS Link down sticky */
+ value = spx5_rd(sparx5, DEV2G5_PCS1G_STICKY(portno));
+ status->link_down = DEV2G5_PCS1G_STICKY_LINK_DOWN_STICKY_GET(value);
+ if (status->link_down) /* Clear the sticky */
+ spx5_wr(value, sparx5, DEV2G5_PCS1G_STICKY(portno));
+
+ /* Get both current Link and Sync status */
+ value = spx5_rd(sparx5, DEV2G5_PCS1G_LINK_STATUS(portno));
+ status->link = DEV2G5_PCS1G_LINK_STATUS_LINK_STATUS_GET(value) &&
+ DEV2G5_PCS1G_LINK_STATUS_SYNC_STATUS_GET(value);
+
+ if (port->conf.portmode == PHY_INTERFACE_MODE_1000BASEX)
+ status->speed = SPEED_1000;
+ else if (port->conf.portmode == PHY_INTERFACE_MODE_2500BASEX)
+ status->speed = SPEED_2500;
+
+ status->duplex = DUPLEX_FULL;
+
+ /* Get PCS ANEG status register */
+ value = spx5_rd(sparx5, DEV2G5_PCS1G_ANEG_STATUS(portno));
+
+ /* Aneg complete provides more information */
+ if (DEV2G5_PCS1G_ANEG_STATUS_ANEG_COMPLETE_GET(value)) {
+ lp_adv = DEV2G5_PCS1G_ANEG_STATUS_LP_ADV_ABILITY_GET(value);
+ if (port->conf.portmode == PHY_INTERFACE_MODE_SGMII) {
+ decode_sgmii_word(lp_adv, status);
+ } else {
+ value = spx5_rd(sparx5, DEV2G5_PCS1G_ANEG_CFG(portno));
+ ld_adv = DEV2G5_PCS1G_ANEG_CFG_ADV_ABILITY_GET(value);
+ decode_cl37_word(lp_adv, ld_adv, status);
+ }
+ }
+ return 0;
+}
+
+static int sparx5_get_sfi_status(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_status *status)
+{
+ bool high_speed_dev = sparx5_is_high_speed_device(&port->conf);
+ u32 portno = port->portno;
+ u32 value, dev, tinst;
+ void __iomem *inst;
+
+ if (!high_speed_dev) {
+ netdev_err(port->ndev, "error: low speed and SFI mode\n");
+ return -EINVAL;
+ }
+
+ dev = sparx5_to_high_dev(portno);
+ tinst = sparx5_port_dev_index(portno);
+ inst = spx5_inst_get(sparx5, dev, tinst);
+
+ value = spx5_inst_rd(inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
+ if (value != DEV10G_MAC_TX_MONITOR_STICKY_IDLE_STATE_STICKY) {
+ /* The link is or has been down. Clear the sticky bit */
+ status->link_down = 1;
+ spx5_inst_wr(0xffffffff, inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
+ value = spx5_inst_rd(inst, DEV10G_MAC_TX_MONITOR_STICKY(0));
+ }
+ status->link = (value == DEV10G_MAC_TX_MONITOR_STICKY_IDLE_STATE_STICKY);
+ status->speed = port->conf.speed;
+ status->duplex = DUPLEX_FULL;
+ return 0;
+}
+
+/* Get link status of 1000Base-X/in-band and SFI ports.
+ */
+int sparx5_get_port_status(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_status *status)
+{
+ memset(status, 0, sizeof(*status));
+ status->speed = port->conf.speed;
+ if (port->conf.power_down) {
+ status->link = false;
+ return 0;
+ }
+ switch (port->conf.portmode) {
+ case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_QSGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
+ return sparx5_get_dev2g5_status(sparx5, port, status);
+ case PHY_INTERFACE_MODE_10GBASER:
+ return sparx5_get_sfi_status(sparx5, port, status);
+ case PHY_INTERFACE_MODE_NA:
+ return 0;
+ default:
+ netdev_err(port->ndev, "Status not supported");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+static int sparx5_port_error(struct sparx5_port *port,
+ struct sparx5_port_config *conf,
+ enum port_error errtype)
+{
+ switch (errtype) {
+ case SPX5_PERR_SPEED:
+ netdev_err(port->ndev,
+ "Interface does not support speed: %u: for %s\n",
+ conf->speed, phy_modes(conf->portmode));
+ break;
+ case SPX5_PERR_IFTYPE:
+ netdev_err(port->ndev,
+ "Switch port does not support interface type: %s\n",
+ phy_modes(conf->portmode));
+ break;
+ default:
+ netdev_err(port->ndev,
+ "Interface configuration error\n");
+ }
+
+ return -EINVAL;
+}
+
+static int sparx5_port_verify_speed(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ if ((sparx5_port_is_2g5(port->portno) &&
+ conf->speed > SPEED_2500) ||
+ (sparx5_port_is_5g(port->portno) &&
+ conf->speed > SPEED_5000) ||
+ (sparx5_port_is_10g(port->portno) &&
+ conf->speed > SPEED_10000))
+ return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+
+ switch (conf->portmode) {
+ case PHY_INTERFACE_MODE_NA:
+ return -EINVAL;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ if (conf->speed != SPEED_1000 ||
+ sparx5_port_is_2g5(port->portno))
+ return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+ if (sparx5_port_is_2g5(port->portno))
+ return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
+ break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ if (conf->speed != SPEED_2500 ||
+ sparx5_port_is_2g5(port->portno))
+ return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+ break;
+ case PHY_INTERFACE_MODE_QSGMII:
+ if (port->portno > 47)
+ return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
+ fallthrough;
+ case PHY_INTERFACE_MODE_SGMII:
+ if (conf->speed != SPEED_1000 &&
+ conf->speed != SPEED_100 &&
+ conf->speed != SPEED_10 &&
+ conf->speed != SPEED_2500)
+ return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+ break;
+ case PHY_INTERFACE_MODE_10GBASER:
+ if ((conf->speed != SPEED_5000 &&
+ conf->speed != SPEED_10000 &&
+ conf->speed != SPEED_25000))
+ return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+ break;
+ default:
+ return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
+ }
+ return 0;
+}
+
+static bool sparx5_dev_change(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ if (port->conf.portmode != conf->portmode)
+ if (port->conf.portmode == PHY_INTERFACE_MODE_10GBASER ||
+ conf->portmode == PHY_INTERFACE_MODE_10GBASER)
+ return true;
+
+ return false;
+}
+
+static int sparx5_port_flush_poll(struct sparx5 *sparx5, u32 portno)
+{
+ u32 value, resource, prio, delay_cnt = 0;
+ bool poll_src = true;
+ char *mem = "";
+
+ /* Resource == 0: Memory tracked per source (SRC-MEM)
+ * Resource == 1: Frame references tracked per source (SRC-REF)
+ * Resource == 2: Memory tracked per destination (DST-MEM)
+ * Resource == 3: Frame references tracked per destination. (DST-REF)
+ */
+ while (1) {
+ bool empty = true;
+
+ for (resource = 0; resource < (poll_src ? 2 : 1); resource++) {
+ u32 base;
+
+ base = (resource == 0 ? 2048 : 0) + SPX5_PRIOS * portno;
+ for (prio = 0; prio < SPX5_PRIOS; prio++) {
+ value = spx5_rd(sparx5,
+ QRES_RES_STAT(base + prio));
+ if (value) {
+ mem = resource == 0 ?
+ "DST-MEM" : "SRC-MEM";
+ empty = false;
+ }
+ }
+ }
+
+ if (empty)
+ break;
+
+ if (delay_cnt++ == 2000) {
+ dev_err(sparx5->dev,
+ "Flush timeout port %u. %s queue not empty\n",
+ portno, mem);
+ return -EINVAL;
+ }
+
+ usleep_range(SPX5_WAIT_US, SPX5_WAIT_MAX_US);
+ }
+ return 0;
+}
+
+static int sparx5_port_disable(struct sparx5 *sparx5, struct sparx5_port *port, bool high_spd_dev)
+{
+ u32 tinst = high_spd_dev ?
+ sparx5_port_dev_index(port->portno) : port->portno;
+ u32 dev = high_spd_dev ?
+ sparx5_to_high_dev(port->portno) : TARGET_DEV2G5;
+ void __iomem *devinst = spx5_inst_get(sparx5, dev, tinst);
+ u32 spd = port->conf.speed;
+ u32 spd_prm;
+ int err;
+
+ if (high_spd_dev) {
+ /* 1: Reset the PCS Rx clock domain */
+ spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_RX_RST,
+ DEV10G_DEV_RST_CTRL_PCS_RX_RST,
+ devinst,
+ DEV10G_DEV_RST_CTRL(0));
+
+ /* 2: Disable MAC frame reception */
+ spx5_inst_rmw(0,
+ DEV10G_MAC_ENA_CFG_RX_ENA,
+ devinst,
+ DEV10G_MAC_ENA_CFG(0));
+ } else {
+ /* 1: Reset the PCS Rx clock domain */
+ spx5_inst_rmw(DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
+ DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
+ devinst,
+ DEV2G5_DEV_RST_CTRL(0));
+ /* 2: Disable MAC frame reception */
+ spx5_inst_rmw(0,
+ DEV2G5_MAC_ENA_CFG_RX_ENA,
+ devinst,
+ DEV2G5_MAC_ENA_CFG(0));
+ }
+ /* 3: Disable traffic being sent to or from switch port->portno */
+ spx5_rmw(0,
+ QFWD_SWITCH_PORT_MODE_PORT_ENA,
+ sparx5,
+ QFWD_SWITCH_PORT_MODE(port->portno));
+
+ /* 4: Disable dequeuing from the egress queues */
+ spx5_rmw(HSCH_PORT_MODE_DEQUEUE_DIS,
+ HSCH_PORT_MODE_DEQUEUE_DIS,
+ sparx5,
+ HSCH_PORT_MODE(port->portno));
+
+ /* 5: Disable Flowcontrol */
+ spx5_rmw(QSYS_PAUSE_CFG_PAUSE_STOP_SET(0xFFF - 1),
+ QSYS_PAUSE_CFG_PAUSE_STOP,
+ sparx5,
+ QSYS_PAUSE_CFG(port->portno));
+
+ spd_prm = spd == SPEED_10 ? 1000 : spd == SPEED_100 ? 100 : 10;
+ /* 6: Wait while the last frame is exiting the queues */
+ usleep_range(8 * spd_prm, 10 * spd_prm);
+
+ /* 7: Flush the queues accociated with the port->portno */
+ spx5_rmw(HSCH_FLUSH_CTRL_FLUSH_PORT_SET(port->portno) |
+ HSCH_FLUSH_CTRL_FLUSH_DST_SET(1) |
+ HSCH_FLUSH_CTRL_FLUSH_SRC_SET(1) |
+ HSCH_FLUSH_CTRL_FLUSH_ENA_SET(1),
+ HSCH_FLUSH_CTRL_FLUSH_PORT |
+ HSCH_FLUSH_CTRL_FLUSH_DST |
+ HSCH_FLUSH_CTRL_FLUSH_SRC |
+ HSCH_FLUSH_CTRL_FLUSH_ENA,
+ sparx5,
+ HSCH_FLUSH_CTRL);
+
+ /* 8: Enable dequeuing from the egress queues */
+ spx5_rmw(0,
+ HSCH_PORT_MODE_DEQUEUE_DIS,
+ sparx5,
+ HSCH_PORT_MODE(port->portno));
+
+ /* 9: Wait until flushing is complete */
+ err = sparx5_port_flush_poll(sparx5, port->portno);
+ if (err)
+ return err;
+
+ /* 10: Reset the MAC clock domain */
+ if (high_spd_dev) {
+ spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_TX_RST_SET(1) |
+ DEV10G_DEV_RST_CTRL_MAC_RX_RST_SET(1) |
+ DEV10G_DEV_RST_CTRL_MAC_TX_RST_SET(1),
+ DEV10G_DEV_RST_CTRL_PCS_TX_RST |
+ DEV10G_DEV_RST_CTRL_MAC_RX_RST |
+ DEV10G_DEV_RST_CTRL_MAC_TX_RST,
+ devinst,
+ DEV10G_DEV_RST_CTRL(0));
+
+ } else {
+ spx5_inst_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(3) |
+ DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(1) |
+ DEV2G5_DEV_RST_CTRL_PCS_RX_RST_SET(1) |
+ DEV2G5_DEV_RST_CTRL_MAC_TX_RST_SET(1) |
+ DEV2G5_DEV_RST_CTRL_MAC_RX_RST_SET(1),
+ DEV2G5_DEV_RST_CTRL_SPEED_SEL |
+ DEV2G5_DEV_RST_CTRL_PCS_TX_RST |
+ DEV2G5_DEV_RST_CTRL_PCS_RX_RST |
+ DEV2G5_DEV_RST_CTRL_MAC_TX_RST |
+ DEV2G5_DEV_RST_CTRL_MAC_RX_RST,
+ devinst,
+ DEV2G5_DEV_RST_CTRL(0));
+ }
+ /* 11: Clear flushing */
+ spx5_rmw(HSCH_FLUSH_CTRL_FLUSH_PORT_SET(port->portno) |
+ HSCH_FLUSH_CTRL_FLUSH_ENA_SET(0),
+ HSCH_FLUSH_CTRL_FLUSH_PORT |
+ HSCH_FLUSH_CTRL_FLUSH_ENA,
+ sparx5,
+ HSCH_FLUSH_CTRL);
+
+ if (high_spd_dev) {
+ u32 pcs = sparx5_to_pcs_dev(port->portno);
+ void __iomem *pcsinst = spx5_inst_get(sparx5, pcs, tinst);
+
+ /* 12: Disable 5G/10G/25 BaseR PCS */
+ spx5_inst_rmw(PCS10G_BR_PCS_CFG_PCS_ENA_SET(0),
+ PCS10G_BR_PCS_CFG_PCS_ENA,
+ pcsinst,
+ PCS10G_BR_PCS_CFG(0));
+
+ if (sparx5_port_is_25g(port->portno))
+ /* Disable 25G PCS */
+ spx5_rmw(DEV25G_PCS25G_CFG_PCS25G_ENA_SET(0),
+ DEV25G_PCS25G_CFG_PCS25G_ENA,
+ sparx5,
+ DEV25G_PCS25G_CFG(tinst));
+ } else {
+ /* 12: Disable 1G PCS */
+ spx5_rmw(DEV2G5_PCS1G_CFG_PCS_ENA_SET(0),
+ DEV2G5_PCS1G_CFG_PCS_ENA,
+ sparx5,
+ DEV2G5_PCS1G_CFG(port->portno));
+ }
+
+ /* The port is now flushed and disabled */
+ return 0;
+}
+
+static int sparx5_port_fifo_sz(struct sparx5 *sparx5,
+ u32 portno, u32 speed)
+{
+ u32 sys_clk = sparx5_clk_period(sparx5->coreclock);
+ const u32 taxi_dist[SPX5_PORTS_ALL] = {
+ 6, 8, 10, 6, 8, 10, 6, 8, 10, 6, 8, 10,
+ 4, 4, 4, 4,
+ 11, 12, 13, 14, 15, 16, 17, 18,
+ 11, 12, 13, 14, 15, 16, 17, 18,
+ 11, 12, 13, 14, 15, 16, 17, 18,
+ 11, 12, 13, 14, 15, 16, 17, 18,
+ 4, 6, 8, 4, 6, 8, 6, 8,
+ 2, 2, 2, 2, 2, 2, 2, 4, 2
+ };
+ u32 mac_per = 6400, tmp1, tmp2, tmp3;
+ u32 fifo_width = 16;
+ u32 mac_width = 8;
+ u32 addition = 0;
+
+ switch (speed) {
+ case SPEED_25000:
+ return 0;
+ case SPEED_10000:
+ mac_per = 6400;
+ mac_width = 8;
+ addition = 1;
+ break;
+ case SPEED_5000:
+ mac_per = 12800;
+ mac_width = 8;
+ addition = 0;
+ break;
+ case SPEED_2500:
+ mac_per = 3200;
+ mac_width = 1;
+ addition = 0;
+ break;
+ case SPEED_1000:
+ mac_per = 8000;
+ mac_width = 1;
+ addition = 0;
+ break;
+ case SPEED_100:
+ case SPEED_10:
+ return 1;
+ default:
+ break;
+ }
+
+ tmp1 = 1000 * mac_width / fifo_width;
+ tmp2 = 3000 + ((12000 + 2 * taxi_dist[portno] * 1000)
+ * sys_clk / mac_per);
+ tmp3 = tmp1 * tmp2 / 1000;
+ return (tmp3 + 2000 + 999) / 1000 + addition;
+}
+
+/* Configure port muxing:
+ * QSGMII: 4x2G5 devices
+ */
+static int sparx5_port_mux_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 portno = port->portno;
+ u32 inst;
+
+ if (port->conf.portmode == conf->portmode)
+ return 0; /* Nothing to do */
+
+ switch (conf->portmode) {
+ case PHY_INTERFACE_MODE_QSGMII: /* QSGMII: 4x2G5 devices. Mode Q' */
+ inst = (portno - portno % 4) / 4;
+ spx5_rmw(BIT(inst),
+ BIT(inst),
+ sparx5,
+ PORT_CONF_QSGMII_ENA);
+
+ if ((portno / 4 % 2) == 0) {
+ /* Affects d0-d3,d8-d11..d40-d43 */
+ spx5_rmw(PORT_CONF_USGMII_CFG_BYPASS_SCRAM_SET(1) |
+ PORT_CONF_USGMII_CFG_BYPASS_DESCRAM_SET(1) |
+ PORT_CONF_USGMII_CFG_QUAD_MODE_SET(1),
+ PORT_CONF_USGMII_CFG_BYPASS_SCRAM |
+ PORT_CONF_USGMII_CFG_BYPASS_DESCRAM |
+ PORT_CONF_USGMII_CFG_QUAD_MODE,
+ sparx5,
+ PORT_CONF_USGMII_CFG((portno / 8)));
+ }
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static int sparx5_port_max_tags_set(struct sparx5 *sparx5,
+ struct sparx5_port *port)
+{
+ enum sparx5_port_max_tags max_tags = port->max_vlan_tags;
+ int tag_ct = max_tags == SPX5_PORT_MAX_TAGS_ONE ? 1 :
+ max_tags == SPX5_PORT_MAX_TAGS_TWO ? 2 : 0;
+ bool dtag = max_tags == SPX5_PORT_MAX_TAGS_TWO;
+ enum sparx5_vlan_port_type vlan_type = port->vlan_type;
+ bool dotag = max_tags != SPX5_PORT_MAX_TAGS_NONE;
+ u32 dev = sparx5_to_high_dev(port->portno);
+ u32 tinst = sparx5_port_dev_index(port->portno);
+ void __iomem *inst = spx5_inst_get(sparx5, dev, tinst);
+ u32 etype;
+
+ etype = (vlan_type == SPX5_VLAN_PORT_TYPE_S_CUSTOM ?
+ port->custom_etype :
+ vlan_type == SPX5_VLAN_PORT_TYPE_C ?
+ SPX5_ETYPE_TAG_C : SPX5_ETYPE_TAG_S);
+
+ spx5_wr(DEV2G5_MAC_TAGS_CFG_TAG_ID_SET(etype) |
+ DEV2G5_MAC_TAGS_CFG_PB_ENA_SET(dtag) |
+ DEV2G5_MAC_TAGS_CFG_VLAN_AWR_ENA_SET(dotag) |
+ DEV2G5_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_SET(dotag),
+ sparx5,
+ DEV2G5_MAC_TAGS_CFG(port->portno));
+
+ if (sparx5_port_is_2g5(port->portno))
+ return 0;
+
+ spx5_inst_rmw(DEV10G_MAC_TAGS_CFG_TAG_ID_SET(etype) |
+ DEV10G_MAC_TAGS_CFG_TAG_ENA_SET(dotag),
+ DEV10G_MAC_TAGS_CFG_TAG_ID |
+ DEV10G_MAC_TAGS_CFG_TAG_ENA,
+ inst,
+ DEV10G_MAC_TAGS_CFG(0, 0));
+
+ spx5_inst_rmw(DEV10G_MAC_NUM_TAGS_CFG_NUM_TAGS_SET(tag_ct),
+ DEV10G_MAC_NUM_TAGS_CFG_NUM_TAGS,
+ inst,
+ DEV10G_MAC_NUM_TAGS_CFG(0));
+
+ spx5_inst_rmw(DEV10G_MAC_MAXLEN_CFG_MAX_LEN_TAG_CHK_SET(dotag),
+ DEV10G_MAC_MAXLEN_CFG_MAX_LEN_TAG_CHK,
+ inst,
+ DEV10G_MAC_MAXLEN_CFG(0));
+ return 0;
+}
+
+static int sparx5_port_fwd_urg(struct sparx5 *sparx5, u32 speed)
+{
+ u32 clk_period_ps = 1600; /* 625Mhz for now */
+ u32 urg = 672000;
+
+ switch (speed) {
+ case SPEED_10:
+ case SPEED_100:
+ case SPEED_1000:
+ urg = 672000;
+ break;
+ case SPEED_2500:
+ urg = 270000;
+ break;
+ case SPEED_5000:
+ urg = 135000;
+ break;
+ case SPEED_10000:
+ urg = 67200;
+ break;
+ case SPEED_25000:
+ urg = 27000;
+ break;
+ }
+ return urg / clk_period_ps - 1;
+}
+
+static u16 sparx5_wm_enc(u16 value)
+{
+ if (value >= 2048)
+ return 2048 + value / 16;
+
+ return value;
+}
+
+static int sparx5_port_fc_setup(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ bool fc_obey = conf->pause & MLO_PAUSE_RX ? 1 : 0;
+ u32 pause_stop = 0xFFF - 1; /* FC gen disabled */
+
+ if (conf->pause & MLO_PAUSE_TX)
+ pause_stop = sparx5_wm_enc(4 * (ETH_MAXLEN /
+ SPX5_BUFFER_CELL_SZ));
+
+ /* Set HDX flowcontrol */
+ spx5_rmw(DSM_MAC_CFG_HDX_BACKPREASSURE_SET(conf->duplex == DUPLEX_HALF),
+ DSM_MAC_CFG_HDX_BACKPREASSURE,
+ sparx5,
+ DSM_MAC_CFG(port->portno));
+
+ /* Obey flowcontrol */
+ spx5_rmw(DSM_RX_PAUSE_CFG_RX_PAUSE_EN_SET(fc_obey),
+ DSM_RX_PAUSE_CFG_RX_PAUSE_EN,
+ sparx5,
+ DSM_RX_PAUSE_CFG(port->portno));
+
+ /* Disable forward pressure */
+ spx5_rmw(QSYS_FWD_PRESSURE_FWD_PRESSURE_DIS_SET(fc_obey),
+ QSYS_FWD_PRESSURE_FWD_PRESSURE_DIS,
+ sparx5,
+ QSYS_FWD_PRESSURE(port->portno));
+
+ /* Generate pause frames */
+ spx5_rmw(QSYS_PAUSE_CFG_PAUSE_STOP_SET(pause_stop),
+ QSYS_PAUSE_CFG_PAUSE_STOP,
+ sparx5,
+ QSYS_PAUSE_CFG(port->portno));
+
+ return 0;
+}
+
+static u16 sparx5_get_aneg_word(struct sparx5_port_config *conf)
+{
+ if (conf->portmode == PHY_INTERFACE_MODE_1000BASEX) /* cl-37 aneg */
+ return (ADVERTISE_LPACK |
+ (conf->pause == MLO_PAUSE_AN ? ADVERTISE_1000XPAUSE : 0) |
+ (conf->pause == MLO_PAUSE_AN ? ADVERTISE_1000XPSE_ASYM : 0) |
+ ADVERTISE_1000XFULL);
+ else
+ return 1; /* Enable SGMII Aneg */
+}
+
+int sparx5_serdes_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ int err;
+
+ if (conf->portmode == PHY_INTERFACE_MODE_QSGMII &&
+ ((port->portno % 4) != 0)) {
+ return 0;
+ }
+ err = phy_set_media(port->serdes, conf->media);
+ if (err)
+ return err;
+ if (conf->speed > 0) {
+ err = phy_set_speed(port->serdes, conf->speed);
+ if (err)
+ return err;
+ }
+ if (conf->serdes_reset) {
+ err = phy_reset(port->serdes);
+ if (err)
+ return err;
+ }
+ /* Configure SerDes with port parameters */
+ err = phy_set_mode_ext(port->serdes, PHY_MODE_ETHERNET, conf->portmode);
+ if (err)
+ return err;
+ conf->serdes_reset = false;
+ return err;
+}
+
+static int sparx5_port_pcs_low_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ bool sgmii = false, inband_aneg = false;
+ int err;
+
+ if (!port->conf.has_sfp) {
+ sgmii = true; /* Phy is connnected to the MAC */
+ } else {
+ if (conf->portmode == PHY_INTERFACE_MODE_SGMII ||
+ conf->portmode == PHY_INTERFACE_MODE_QSGMII)
+ inband_aneg = true; /* Cisco-SGMII in-band-aneg */
+ else if (conf->portmode == PHY_INTERFACE_MODE_1000BASEX &&
+ conf->autoneg)
+ inband_aneg = true; /* Clause-37 in-band-aneg */
+
+ err = sparx5_serdes_set(sparx5, port, conf);
+ if (err)
+ return -EINVAL;
+ }
+
+ /* Choose SGMII or 1000BaseX/2500BaseX PCS mode */
+ spx5_rmw(DEV2G5_PCS1G_MODE_CFG_SGMII_MODE_ENA_SET(sgmii),
+ DEV2G5_PCS1G_MODE_CFG_SGMII_MODE_ENA,
+ sparx5,
+ DEV2G5_PCS1G_MODE_CFG(port->portno));
+
+ /* Enable PCS */
+ spx5_wr(DEV2G5_PCS1G_CFG_PCS_ENA_SET(1),
+ sparx5,
+ DEV2G5_PCS1G_CFG(port->portno));
+
+ if (inband_aneg) {
+ u16 abil = sparx5_get_aneg_word(conf);
+
+ /* Enable in-band aneg */
+ spx5_wr(DEV2G5_PCS1G_ANEG_CFG_ADV_ABILITY_SET(abil) |
+ DEV2G5_PCS1G_ANEG_CFG_SW_RESOLVE_ENA_SET(1) |
+ DEV2G5_PCS1G_ANEG_CFG_ANEG_ENA_SET(1) |
+ DEV2G5_PCS1G_ANEG_CFG_ANEG_RESTART_ONE_SHOT_SET(1),
+ sparx5,
+ DEV2G5_PCS1G_ANEG_CFG(port->portno));
+ } else {
+ spx5_wr(0, sparx5, DEV2G5_PCS1G_ANEG_CFG(port->portno));
+ }
+
+ /* Take PCS out of reset */
+ spx5_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(2) |
+ DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(0) |
+ DEV2G5_DEV_RST_CTRL_PCS_RX_RST_SET(0),
+ DEV2G5_DEV_RST_CTRL_SPEED_SEL |
+ DEV2G5_DEV_RST_CTRL_PCS_TX_RST |
+ DEV2G5_DEV_RST_CTRL_PCS_RX_RST,
+ sparx5,
+ DEV2G5_DEV_RST_CTRL(port->portno));
+
+ return 0;
+}
+
+static int sparx5_port_pcs_high_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 clk_spd = conf->speed == SPEED_5000 ? 1 : 0;
+ u32 pix = sparx5_port_dev_index(port->portno);
+ u32 dev = sparx5_to_high_dev(port->portno);
+ u32 pcs = sparx5_to_pcs_dev(port->portno);
+ void __iomem *devinst;
+ void __iomem *pcsinst;
+ int err;
+
+ devinst = spx5_inst_get(sparx5, dev, pix);
+ pcsinst = spx5_inst_get(sparx5, pcs, pix);
+
+ /* SFI : No in-band-aneg. Speeds 5G/10G/25G */
+ err = sparx5_serdes_set(sparx5, port, conf);
+ if (err)
+ return -EINVAL;
+
+ if (conf->speed == SPEED_25000) {
+ /* Enable PCS for 25G device, speed 25G */
+ spx5_rmw(DEV25G_PCS25G_CFG_PCS25G_ENA_SET(1),
+ DEV25G_PCS25G_CFG_PCS25G_ENA,
+ sparx5,
+ DEV25G_PCS25G_CFG(pix));
+ } else {
+ /* Enable PCS for 5G/10G/25G devices, speed 5G/10G */
+ spx5_inst_rmw(PCS10G_BR_PCS_CFG_PCS_ENA_SET(1),
+ PCS10G_BR_PCS_CFG_PCS_ENA,
+ pcsinst,
+ PCS10G_BR_PCS_CFG(0));
+ }
+
+ /* Enable 5G/10G/25G MAC module */
+ spx5_inst_wr(DEV10G_MAC_ENA_CFG_RX_ENA_SET(1) |
+ DEV10G_MAC_ENA_CFG_TX_ENA_SET(1),
+ devinst,
+ DEV10G_MAC_ENA_CFG(0));
+
+ /* Take the device out of reset */
+ spx5_inst_rmw(DEV10G_DEV_RST_CTRL_PCS_RX_RST_SET(0) |
+ DEV10G_DEV_RST_CTRL_PCS_TX_RST_SET(0) |
+ DEV10G_DEV_RST_CTRL_MAC_RX_RST_SET(0) |
+ DEV10G_DEV_RST_CTRL_MAC_TX_RST_SET(0) |
+ DEV10G_DEV_RST_CTRL_SPEED_SEL_SET(clk_spd),
+ DEV10G_DEV_RST_CTRL_PCS_RX_RST |
+ DEV10G_DEV_RST_CTRL_PCS_TX_RST |
+ DEV10G_DEV_RST_CTRL_MAC_RX_RST |
+ DEV10G_DEV_RST_CTRL_MAC_TX_RST |
+ DEV10G_DEV_RST_CTRL_SPEED_SEL,
+ devinst,
+ DEV10G_DEV_RST_CTRL(0));
+
+ return 0;
+}
+
+/* Switch between 1G/2500 and 5G/10G/25G devices */
+static void sparx5_dev_switch(struct sparx5 *sparx5, int port, bool hsd)
+{
+ int bt_indx = BIT(sparx5_port_dev_index(port));
+
+ if (sparx5_port_is_5g(port)) {
+ spx5_rmw(hsd ? 0 : bt_indx,
+ bt_indx,
+ sparx5,
+ PORT_CONF_DEV5G_MODES);
+ } else if (sparx5_port_is_10g(port)) {
+ spx5_rmw(hsd ? 0 : bt_indx,
+ bt_indx,
+ sparx5,
+ PORT_CONF_DEV10G_MODES);
+ } else if (sparx5_port_is_25g(port)) {
+ spx5_rmw(hsd ? 0 : bt_indx,
+ bt_indx,
+ sparx5,
+ PORT_CONF_DEV25G_MODES);
+ }
+}
+
+/* Configure speed/duplex dependent registers */
+static int sparx5_port_config_low_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 clk_spd, gig_mode, tx_gap, hdx_gap_1, hdx_gap_2;
+ bool fdx = conf->duplex == DUPLEX_FULL;
+ int spd = conf->speed;
+
+ clk_spd = spd == SPEED_10 ? 0 : spd == SPEED_100 ? 1 : 2;
+ gig_mode = spd == SPEED_1000 || spd == SPEED_2500;
+ tx_gap = spd == SPEED_1000 ? 4 : fdx ? 6 : 5;
+ hdx_gap_1 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 1 : 2;
+ hdx_gap_2 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 4 : 1;
+
+ /* GIG/FDX mode */
+ spx5_rmw(DEV2G5_MAC_MODE_CFG_GIGA_MODE_ENA_SET(gig_mode) |
+ DEV2G5_MAC_MODE_CFG_FDX_ENA_SET(fdx),
+ DEV2G5_MAC_MODE_CFG_GIGA_MODE_ENA |
+ DEV2G5_MAC_MODE_CFG_FDX_ENA,
+ sparx5,
+ DEV2G5_MAC_MODE_CFG(port->portno));
+
+ /* Set MAC IFG Gaps */
+ spx5_wr(DEV2G5_MAC_IFG_CFG_TX_IFG_SET(tx_gap) |
+ DEV2G5_MAC_IFG_CFG_RX_IFG1_SET(hdx_gap_1) |
+ DEV2G5_MAC_IFG_CFG_RX_IFG2_SET(hdx_gap_2),
+ sparx5,
+ DEV2G5_MAC_IFG_CFG(port->portno));
+
+ /* Disabling frame aging when in HDX (due to HDX issue) */
+ spx5_rmw(HSCH_PORT_MODE_AGE_DIS_SET(fdx == 0),
+ HSCH_PORT_MODE_AGE_DIS,
+ sparx5,
+ HSCH_PORT_MODE(port->portno));
+
+ /* Enable MAC module */
+ spx5_wr(DEV2G5_MAC_ENA_CFG_RX_ENA |
+ DEV2G5_MAC_ENA_CFG_TX_ENA,
+ sparx5,
+ DEV2G5_MAC_ENA_CFG(port->portno));
+
+ /* Select speed and take MAC out of reset */
+ spx5_rmw(DEV2G5_DEV_RST_CTRL_SPEED_SEL_SET(clk_spd) |
+ DEV2G5_DEV_RST_CTRL_MAC_TX_RST_SET(0) |
+ DEV2G5_DEV_RST_CTRL_MAC_RX_RST_SET(0),
+ DEV2G5_DEV_RST_CTRL_SPEED_SEL |
+ DEV2G5_DEV_RST_CTRL_MAC_TX_RST |
+ DEV2G5_DEV_RST_CTRL_MAC_RX_RST,
+ sparx5,
+ DEV2G5_DEV_RST_CTRL(port->portno));
+
+ return 0;
+}
+
+int sparx5_port_pcs_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+
+{
+ bool high_speed_dev = sparx5_is_high_speed_device(conf);
+ int err;
+
+ if (sparx5_dev_change(sparx5, port, conf)) {
+ /* switch device */
+ sparx5_dev_switch(sparx5, port->portno, high_speed_dev);
+
+ /* Disable the not-in-use device */
+ err = sparx5_port_disable(sparx5, port, !high_speed_dev);
+ if (err)
+ return err;
+ }
+ /* Disable the port before re-configuring */
+ err = sparx5_port_disable(sparx5, port, high_speed_dev);
+ if (err)
+ return -EINVAL;
+
+ if (high_speed_dev)
+ err = sparx5_port_pcs_high_set(sparx5, port, conf);
+ else
+ err = sparx5_port_pcs_low_set(sparx5, port, conf);
+
+ if (err)
+ return -EINVAL;
+
+ if (port->conf.has_sfp) {
+ /* Enable/disable 1G counters in ASM */
+ spx5_rmw(ASM_PORT_CFG_CSC_STAT_DIS_SET(high_speed_dev),
+ ASM_PORT_CFG_CSC_STAT_DIS,
+ sparx5,
+ ASM_PORT_CFG(port->portno));
+
+ /* Enable/disable 1G counters in DSM */
+ spx5_rmw(DSM_BUF_CFG_CSC_STAT_DIS_SET(high_speed_dev),
+ DSM_BUF_CFG_CSC_STAT_DIS,
+ sparx5,
+ DSM_BUF_CFG(port->portno));
+ }
+
+ port->conf = *conf;
+
+ return 0;
+}
+
+int sparx5_port_config(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ bool high_speed_dev = sparx5_is_high_speed_device(conf);
+ int err, urgency, stop_wm;
+
+ err = sparx5_port_verify_speed(sparx5, port, conf);
+ if (err)
+ return err;
+
+ /* high speed device is already configured */
+ if (!high_speed_dev)
+ sparx5_port_config_low_set(sparx5, port, conf);
+
+ /* Configure flow control */
+ err = sparx5_port_fc_setup(sparx5, port, conf);
+ if (err)
+ return err;
+
+ /* Set the DSM stop watermark */
+ stop_wm = sparx5_port_fifo_sz(sparx5, port->portno, conf->speed);
+ spx5_rmw(DSM_DEV_TX_STOP_WM_CFG_DEV_TX_STOP_WM_SET(stop_wm),
+ DSM_DEV_TX_STOP_WM_CFG_DEV_TX_STOP_WM,
+ sparx5,
+ DSM_DEV_TX_STOP_WM_CFG(port->portno));
+
+ /* Enable port in queue system */
+ urgency = sparx5_port_fwd_urg(sparx5, conf->speed);
+ spx5_rmw(QFWD_SWITCH_PORT_MODE_PORT_ENA_SET(1) |
+ QFWD_SWITCH_PORT_MODE_FWD_URGENCY_SET(urgency),
+ QFWD_SWITCH_PORT_MODE_PORT_ENA |
+ QFWD_SWITCH_PORT_MODE_FWD_URGENCY,
+ sparx5,
+ QFWD_SWITCH_PORT_MODE(port->portno));
+
+ /* Save the new values */
+ port->conf = *conf;
+
+ return 0;
+}
+
+/* Initialize port config to default */
+int sparx5_port_init(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 pause_start = sparx5_wm_enc(6 * (ETH_MAXLEN / SPX5_BUFFER_CELL_SZ));
+ u32 atop = sparx5_wm_enc(20 * (ETH_MAXLEN / SPX5_BUFFER_CELL_SZ));
+ u32 devhigh = sparx5_to_high_dev(port->portno);
+ u32 pix = sparx5_port_dev_index(port->portno);
+ u32 pcs = sparx5_to_pcs_dev(port->portno);
+ bool sd_pol = port->signd_active_high;
+ bool sd_sel = !port->signd_internal;
+ bool sd_ena = port->signd_enable;
+ u32 pause_stop = 0xFFF - 1; /* FC generate disabled */
+ void __iomem *devinst;
+ void __iomem *pcsinst;
+ int err;
+
+ devinst = spx5_inst_get(sparx5, devhigh, pix);
+ pcsinst = spx5_inst_get(sparx5, pcs, pix);
+
+ /* Set the mux port mode */
+ err = sparx5_port_mux_set(sparx5, port, conf);
+ if (err)
+ return err;
+
+ /* Configure MAC vlan awareness */
+ err = sparx5_port_max_tags_set(sparx5, port);
+ if (err)
+ return err;
+
+ /* Set Max Length */
+ spx5_rmw(DEV2G5_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
+ DEV2G5_MAC_MAXLEN_CFG_MAX_LEN,
+ sparx5,
+ DEV2G5_MAC_MAXLEN_CFG(port->portno));
+
+ /* 1G/2G5: Signal Detect configuration */
+ spx5_wr(DEV2G5_PCS1G_SD_CFG_SD_POL_SET(sd_pol) |
+ DEV2G5_PCS1G_SD_CFG_SD_SEL_SET(sd_sel) |
+ DEV2G5_PCS1G_SD_CFG_SD_ENA_SET(sd_ena),
+ sparx5,
+ DEV2G5_PCS1G_SD_CFG(port->portno));
+
+ /* Set Pause WM hysteresis */
+ spx5_rmw(QSYS_PAUSE_CFG_PAUSE_START_SET(pause_start) |
+ QSYS_PAUSE_CFG_PAUSE_STOP_SET(pause_stop) |
+ QSYS_PAUSE_CFG_PAUSE_ENA_SET(1),
+ QSYS_PAUSE_CFG_PAUSE_START |
+ QSYS_PAUSE_CFG_PAUSE_STOP |
+ QSYS_PAUSE_CFG_PAUSE_ENA,
+ sparx5,
+ QSYS_PAUSE_CFG(port->portno));
+
+ /* Port ATOP. Frames are tail dropped when this WM is hit */
+ spx5_wr(QSYS_ATOP_ATOP_SET(atop),
+ sparx5,
+ QSYS_ATOP(port->portno));
+
+ /* Discard pause frame 01-80-C2-00-00-01 */
+ spx5_wr(PAUSE_DISCARD, sparx5, ANA_CL_CAPTURE_BPDU_CFG(port->portno));
+
+ if (conf->portmode == PHY_INTERFACE_MODE_QSGMII ||
+ conf->portmode == PHY_INTERFACE_MODE_SGMII) {
+ err = sparx5_serdes_set(sparx5, port, conf);
+ if (err)
+ return err;
+
+ if (!sparx5_port_is_2g5(port->portno))
+ /* Enable shadow device */
+ spx5_rmw(DSM_DEV_TX_STOP_WM_CFG_DEV10G_SHADOW_ENA_SET(1),
+ DSM_DEV_TX_STOP_WM_CFG_DEV10G_SHADOW_ENA,
+ sparx5,
+ DSM_DEV_TX_STOP_WM_CFG(port->portno));
+
+ sparx5_dev_switch(sparx5, port->portno, false);
+ }
+ if (conf->portmode == PHY_INTERFACE_MODE_QSGMII) {
+ // All ports must be PCS enabled in QSGMII mode
+ spx5_rmw(DEV2G5_DEV_RST_CTRL_PCS_TX_RST_SET(0),
+ DEV2G5_DEV_RST_CTRL_PCS_TX_RST,
+ sparx5,
+ DEV2G5_DEV_RST_CTRL(port->portno));
+ }
+ /* Default IFGs for 1G */
+ spx5_wr(DEV2G5_MAC_IFG_CFG_TX_IFG_SET(6) |
+ DEV2G5_MAC_IFG_CFG_RX_IFG1_SET(0) |
+ DEV2G5_MAC_IFG_CFG_RX_IFG2_SET(0),
+ sparx5,
+ DEV2G5_MAC_IFG_CFG(port->portno));
+
+ if (sparx5_port_is_2g5(port->portno))
+ return 0; /* Low speed device only - return */
+
+ /* Now setup the high speed device */
+ if (conf->portmode == PHY_INTERFACE_MODE_NA)
+ conf->portmode = PHY_INTERFACE_MODE_10GBASER;
+
+ if (sparx5_is_high_speed_device(conf))
+ sparx5_dev_switch(sparx5, port->portno, true);
+
+ /* Set Max Length */
+ spx5_inst_rmw(DEV10G_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
+ DEV10G_MAC_MAXLEN_CFG_MAX_LEN,
+ devinst,
+ DEV10G_MAC_ENA_CFG(0));
+
+ /* Handle Signal Detect in 10G PCS */
+ spx5_inst_wr(PCS10G_BR_PCS_SD_CFG_SD_POL_SET(sd_pol) |
+ PCS10G_BR_PCS_SD_CFG_SD_SEL_SET(sd_sel) |
+ PCS10G_BR_PCS_SD_CFG_SD_ENA_SET(sd_ena),
+ pcsinst,
+ PCS10G_BR_PCS_SD_CFG(0));
+
+ if (sparx5_port_is_25g(port->portno)) {
+ /* Handle Signal Detect in 25G PCS */
+ spx5_wr(DEV25G_PCS25G_SD_CFG_SD_POL_SET(sd_pol) |
+ DEV25G_PCS25G_SD_CFG_SD_SEL_SET(sd_sel) |
+ DEV25G_PCS25G_SD_CFG_SD_ENA_SET(sd_ena),
+ sparx5,
+ DEV25G_PCS25G_SD_CFG(pix));
+ }
+
+ return 0;
+}
+
+void sparx5_port_enable(struct sparx5_port *port, bool enable)
+{
+ struct sparx5 *sparx5 = port->sparx5;
+
+ /* Enable port for frame transfer? */
+ spx5_rmw(QFWD_SWITCH_PORT_MODE_PORT_ENA_SET(enable),
+ QFWD_SWITCH_PORT_MODE_PORT_ENA,
+ sparx5,
+ QFWD_SWITCH_PORT_MODE(port->portno));
+}
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.h b/drivers/net/ethernet/microchip/sparx5/sparx5_port.h
new file mode 100644
index 000000000000..86214683f86c
--- /dev/null
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.h
@@ -0,0 +1,98 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/* Microchip Sparx5 Switch driver
+ *
+ * Copyright (c) 2021 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#ifndef __SPARX5_PORT_H__
+#define __SPARX5_PORT_H__
+
+#include "sparx5_main.h"
+
+static inline bool sparx5_port_is_2g5(int portno)
+{
+ return portno >= 16 && portno <= 47;
+}
+
+static inline bool sparx5_port_is_5g(int portno)
+{
+ return portno <= 11 || portno == 64;
+}
+
+static inline bool sparx5_port_is_10g(int portno)
+{
+ return (portno >= 12 && portno <= 15) || (portno >= 48 && portno <= 55);
+}
+
+static inline bool sparx5_port_is_25g(int portno)
+{
+ return portno >= 56 && portno <= 63;
+}
+
+static inline u32 sparx5_to_high_dev(int port)
+{
+ if (sparx5_port_is_5g(port))
+ return TARGET_DEV5G;
+ if (sparx5_port_is_10g(port))
+ return TARGET_DEV10G;
+ return TARGET_DEV25G;
+}
+
+static inline u32 sparx5_to_pcs_dev(int port)
+{
+ if (sparx5_port_is_5g(port))
+ return TARGET_PCS5G_BR;
+ if (sparx5_port_is_10g(port))
+ return TARGET_PCS10G_BR;
+ return TARGET_PCS25G_BR;
+}
+
+static inline int sparx5_port_dev_index(int port)
+{
+ if (sparx5_port_is_2g5(port))
+ return port;
+ if (sparx5_port_is_5g(port))
+ return (port <= 11 ? port : 12);
+ if (sparx5_port_is_10g(port))
+ return (port >= 12 && port <= 15) ?
+ port - 12 : port - 44;
+ return (port - 56);
+}
+
+static inline bool sparx5_is_high_speed_device(struct sparx5_port_config *conf)
+{
+ return conf->portmode == PHY_INTERFACE_MODE_10GBASER;
+}
+
+int sparx5_port_init(struct sparx5 *sparx5,
+ struct sparx5_port *spx5_port,
+ struct sparx5_port_config *conf);
+
+int sparx5_port_config(struct sparx5 *sparx5,
+ struct sparx5_port *spx5_port,
+ struct sparx5_port_config *conf);
+
+int sparx5_port_pcs_set(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_config *conf);
+
+int sparx5_serdes_set(struct sparx5 *sparx5,
+ struct sparx5_port *spx5_port,
+ struct sparx5_port_config *conf);
+
+struct sparx5_port_status {
+ bool link;
+ bool link_down;
+ int speed;
+ bool an_complete;
+ int duplex;
+ int pause;
+};
+
+int sparx5_get_port_status(struct sparx5 *sparx5,
+ struct sparx5_port *port,
+ struct sparx5_port_status *status);
+
+void sparx5_port_enable(struct sparx5_port *port, bool enable);
+
+#endif /* __SPARX5_PORT_H__ */
--
2.31.1
More information about the linux-arm-kernel
mailing list