[PATCH v2 1/2] dt-bindings: pwm: Add Xilinx AXI Timer

[Rob Herring]

On Tue, May 04, 2021 at 02:49:24PM -0400, Sean Anderson wrote:
> This adds a binding for the Xilinx LogiCORE IP AXI Timer. This device is
> a "soft" block, so it has many parameters which would not be
> configurable in most hardware. This binding is usually automatically
> generated by Xilinx's tools, so the names and values of properties
> must be kept as they are.
> 
> Signed-off-by: Sean Anderson <sean.anderson at seco.com>
> ---
> 
> Changes in v2:
> - Use 32-bit addresses for example binding
> 
>  .../bindings/pwm/xlnx,axi-timer.yaml          | 91 +++++++++++++++++++
>  1 file changed, 91 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pwm/xlnx,axi-timer.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pwm/xlnx,axi-timer.yaml b/Documentation/devicetree/bindings/pwm/xlnx,axi-timer.yaml
> new file mode 100644
> index 000000000000..bd014134c322
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pwm/xlnx,axi-timer.yaml
> @@ -0,0 +1,91 @@
> +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pwm/xlnx,axi-timer.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Xilinx LogiCORE IP AXI Timer Device Tree Binding
> +
> +maintainers:
> +  - Sean Anderson <sean.anderson at seco.com>
> +
> +properties:
> +  compatible:
> +    items:
> +      - const: xlnx,axi-timer-2.0
> +      - const: xlnx,xps-timer-1.00.a
> +
> +  clocks:
> +    maxItems: 1
> +
> +  clock-names:
> +    const: s_axi_aclk
> +
> +  reg:
> +    maxItems: 1
> +
> +  xlnx,count-width:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 8
> +    maximum: 32
> +    description:
> +      The width of the counters, in bits.
> +
> +  xlnx,gen0-assert:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description:
> +      The polarity of the generateout0 signal. 0 for active-low, 1 for active-high.
> +
> +  xlnx,gen1-assert:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description:
> +      The polarity of the generateout1 signal. 0 for active-low, 1 for active-high.
> +
> +  xlnx,one-timer-only:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description:
> +      Whether only one timer is present in this block.
> +
> +  xlnx,trig0-assert:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description:
> +      The polarity of the capturetrig0 signal. 0 for active-low, 1 for active-high.
> +
> +  xlnx,trig1-assert:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [ 0, 1 ]
> +    description:
> +      The polarity of the capturetrig1 signal. 0 for active-low, 1 for active-high.

Can't all these be boolean?

> +
> +required:
> +  - compatible
> +  - clocks
> +  - reg
> +  - xlnx,count-width
> +  - xlnx,gen0-assert
> +  - xlnx,gen1-assert
> +  - xlnx,one-timer-only
> +  - xlnx,trig0-assert
> +  - xlnx,trig1-assert
> +
> +additionalProperties: true
> +
> +examples:
> +  - |
> +    axi_timer_0: timer at 800e0000 {
> +        clock-frequency = <99999001>;
> +        clock-names = "s_axi_aclk";
> +        clocks = <&zynqmp_clk 71>;
> +        compatible = "xlnx,axi-timer-2.0", "xlnx,xps-timer-1.00.a";
> +        reg = <0x800e0000 0x10000>;
> +        xlnx,count-width = <0x20>;
> +        xlnx,gen0-assert = <0x1>;
> +        xlnx,gen1-assert = <0x1>;
> +        xlnx,one-timer-only = <0x0>;
> +        xlnx,trig0-assert = <0x1>;
> +        xlnx,trig1-assert = <0x1>;
> +    };
> -- 
> 2.25.1
>