[PATCH 1/2] dt-bindings: pci: convert faraday,ftpci100 to yaml
Rob Herring
robh at kernel.org
Thu May 6 10:43:22 PDT 2021
On Mon, May 03, 2021 at 06:52:27PM +0000, Corentin Labbe wrote:
> Converts pci/faraday,ftpci100.txt to yaml.
> Some change are also made:
> - example has wrong interrupts place
>
> Signed-off-by: Corentin Labbe <clabbe at baylibre.com>
> ---
> .../bindings/pci/faraday,ftpci100.txt | 135 -----------
> .../bindings/pci/faraday,ftpci100.yaml | 211 ++++++++++++++++++
> 2 files changed, 211 insertions(+), 135 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
> create mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml
> diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml b/Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml
> new file mode 100644
> index 000000000000..9be27e71526c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml
> @@ -0,0 +1,211 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/faraday,ftpci100.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Faraday Technology FTPCI100 PCI Host Bridge
> +
> +maintainers:
> + - Linus Walleij <linus.walleij at linaro.org>
> +
> +description: |
> + This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
> + is a generic IP block from Faraday Technology. It exists in two variants:
> + plain and dual PCI. The plain version embeds a cascading interrupt controller
> + into the host bridge. The dual version routes the interrupts to the host
> + chips interrupt controller.
> + The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
> + Technology) and product ID 0x4321.
> +
> +allOf:
> + - $ref: /schemas/pci/pci-bus.yaml#
> +
> +properties:
> + compatible:
> + oneOf:
> + - items:
> + - const: "cortina,gemini-pci"
> + - const: "faraday,ftpci100"
> + - items:
> + - const: "cortina,gemini-pci-dual"
> + - const: "faraday,ftpci100-dual"
> + - const: "faraday,ftpci100"
> + - const: "faraday,ftpci100-dual"
Don't need quotes.
> +
> + reg:
> + minItems: 1
> +
> + "#address-cells":
> + const: 3
> +
> + "#size-cells":
> + const: 2
Covered by pci-bus.yaml.
> +
> + "#interrupt-cells":
> + const: 1
> +
> + bus-range:
> + items:
> + - const: 0x00
> + - const: 0xff
That's the default range, so drop.
> +
> + ranges:
> + minItems: 2
> + description: see pci.txt
Drop the description.
> +
> + dma-ranges:
> + minItems: 3
> + description: |
> + three ranges for the inbound memory region. The ranges must
> + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
> + 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
> + pre-fetchable.
> +
> + clocks:
> + minItems: 2
> + description: |
> + when present, this should contain the peripheral clock (PCLK) and the
> + PCI clock (PCICLK). If these are not present, they are assumed to be
> + hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
Split the description:
items:
- description: peripheral clock (PCLK)
- description: PCI bus? clock (PCICLK). The PCI clock will be 33 or 66 MHz.
> +
> + clock-names:
> + items:
> + - const: "PCLK"
> + - const: "PCICLK"
Drop quotes.
> +
> + interrupt-controller:
> + allOf:
> + - $ref: /schemas/interrupt-controller.yaml#
Drop, this will be applied based on the node name.
> + type: object
> + properties:
> + interrupts:
> + minItems: 1
> +
> + interrupt-controller: true
> +
> + "#address-cells":
> + const: 0
> +
> + "#interrupt-cells":
> + const: 1
> +
> + required:
> + - interrupts
> + - interrupt-controller
> + - "#address-cells"
> + - "#interrupt-cells"
> +
> +required:
> + - reg
> + - compatible
> + - "#address-cells"
> + - "#size-cells"
> + - "#interrupt-cells"
> + - bus-range
> + - ranges
> + - interrupt-map-mask
> + - interrupt-map
> + - dma-ranges
Drop all the ones required in pci-bus.yaml already.
> +
> +if:
> + properties:
> + compatible:
> + contains:
> + items:
> + - const: cortina,gemini-pci
> + - const: faraday,ftpci100
> +then:
> + required:
> + - interrupt-controller
> +
> +unevaluatedProperties: false
> +
> +#I/O space considerations:
> +
> +#The plain variant has 128MiB of non-prefetchable memory space, whereas the
> +#"dual" variant has 64MiB. Take this into account when describing the ranges.
Could go under 'ranges'?
> +
> +#Interrupt map considerations:
Could go under 'interrupt-map'.
> +
> +#The "dual" variant will get INT A, B, C, D from the system interrupt controller
> +#and should point to respective interrupt in that controller in its
> +#interrupt-map.
> +
> +#The code which is the only documentation of how the Faraday PCI (the non-dual
> +#variant) interrupts assigns the default interrupt mapping/swizzling has
> +#typically been like this, doing the swizzling on the interrupt controller side
> +#rather than in the interconnect:
> +
> +#interrupt-map-mask = <0xf800 0 0 7>;
> +#interrupt-map =
> +# <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
> +# <0x4800 0 0 2 &pci_intc 1>,
> +# <0x4800 0 0 3 &pci_intc 2>,
> +# <0x4800 0 0 4 &pci_intc 3>,
> +# <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
> +# <0x5000 0 0 2 &pci_intc 2>,
> +# <0x5000 0 0 3 &pci_intc 3>,
> +# <0x5000 0 0 4 &pci_intc 0>,
> +# <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
> +# <0x5800 0 0 2 &pci_intc 3>,
> +# <0x5800 0 0 3 &pci_intc 0>,
> +# <0x5800 0 0 4 &pci_intc 1>,
> +# <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
> +# <0x6000 0 0 2 &pci_intc 0>,
> +# <0x6000 0 0 3 &pci_intc 1>,
> +# <0x6000 0 0 4 &pci_intc 2>;
> +
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + pci at 50000000 {
> + compatible = "cortina,gemini-pci", "faraday,ftpci100";
> + reg = <0x50000000 0x100>;
> + device_type = "pci";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> +
> + bus-range = <0x00 0xff>;
> + ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
> + <0x01000000 0 0 0x50000000 0 0x00100000>,
> + /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
> + <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
> +
> + /* DMA ranges */
> + dma-ranges =
> + /* 128MiB at 0x00000000-0x07ffffff */
> + <0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
> + /* 64MiB at 0x00000000-0x03ffffff */
> + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
> + /* 64MiB at 0x00000000-0x03ffffff */
> + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
> +
> + interrupt-map-mask = <0xf800 0 0 7>;
> + interrupt-map =
> + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
> + <0x4800 0 0 2 &pci_intc 1>,
> + <0x4800 0 0 3 &pci_intc 2>,
> + <0x4800 0 0 4 &pci_intc 3>,
> + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
> + <0x5000 0 0 2 &pci_intc 2>,
> + <0x5000 0 0 3 &pci_intc 3>,
> + <0x5000 0 0 4 &pci_intc 0>,
> + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
> + <0x5800 0 0 2 &pci_intc 3>,
> + <0x5800 0 0 3 &pci_intc 0>,
> + <0x5800 0 0 4 &pci_intc 1>,
> + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
> + <0x6000 0 0 2 &pci_intc 0>,
> + <0x6000 0 0 3 &pci_intc 0>,
> + <0x6000 0 0 4 &pci_intc 0>;
> + pci_intc: interrupt-controller {
> + interrupt-parent = <&intcon>;
> + interrupt-controller;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + };
> + };
> --
> 2.26.3
>
More information about the linux-arm-kernel
mailing list