[PATCH v8 4/6] ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
Alexandre TORGUE
alexandre.torgue at foss.st.com
Wed Mar 31 08:18:24 BST 2021
Hi Dillon
On 3/31/21 12:43 AM, dillon min wrote:
> Hi Alexandre,
>
> Thanks for the quick response.
>
> On Wed, Mar 31, 2021 at 12:50 AM Alexandre TORGUE
> <alexandre.torgue at foss.st.com> wrote:
>>
>>
>>
>> On 3/30/21 10:58 AM, dillon.minfei at gmail.com wrote:
>>> From: dillon min <dillon.minfei at gmail.com>
>>>
>>> This patchset has following changes:
>>>
>>> - introduce stm32h750.dtsi to support stm32h750 value line
>>> - add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
>>> - add stm32h750-art-pi.dts to support art-pi board
>>>
>>> art-pi board component:
>>> - 8MiB qspi flash
>>> - 16MiB spi flash
>>> - 32MiB sdram
>>> - ap6212 wifi&bt&fm
>>>
>>> the detail board information can be found at:
>>> https://art-pi.gitee.io/website/
>>>
>>> Signed-off-by: dillon min <dillon.minfei at gmail.com>
>>> ---
>>> v8:
>>> - move file stm32h743.dtsi submit position to [PATCH V8 3/6]
>>>
>>> arch/arm/boot/dts/Makefile | 1 +
>>> arch/arm/boot/dts/stm32h750.dtsi | 6 +
>>> arch/arm/boot/dts/stm32h750i-art-pi.dts | 229 ++++++++++++++++++++++++++++++++
>>> 3 files changed, 236 insertions(+)
>>> create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
>>> create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index 8e5d4ab4e75e..a19c5ab9df84 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1071,6 +1071,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
>>> stm32746g-eval.dtb \
>>> stm32h743i-eval.dtb \
>>> stm32h743i-disco.dtb \
>>> + stm32h750i-art-pi.dtb \
>>> stm32mp153c-dhcom-drc02.dtb \
>>> stm32mp157a-avenger96.dtb \
>>> stm32mp157a-dhcor-avenger96.dtb \
>>> diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
>>> new file mode 100644
>>> index 000000000000..41e3b1e3a874
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32h750.dtsi
>>> @@ -0,0 +1,6 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
>>> +/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
>>> +
>>> +#include "stm32h743.dtsi"
>>> +
>>
>> I know it's a bit odd, but you could directly include stm32h743.dtsi in
>> your board as there are no SoC differences.
>
> There are some mirror difference between stm32h743 and stm32h750:
>
> Number of A/D Converters (typ): stm32h743(none), stm32h750(3)
> Crypto: stm32h743(none), stm32h750(HASH-AES, DES/TDES, HMAC, MD5, SHA)
>
> you can find detail diff at link:
> https://www.st.com/en/microcontrollers-microprocessors/stm32h7-series.html#products
> (select stm32h743xi, stm32h750xb to compare)
>
> I have two options for this changes.
> - rename stm32h743.dtsi to stm32h7.dtsi, add crypto part to
> stm32h7.dtsi in the future.
> - make the reference like this (just like stm32f429 <-- stm32f469,
> stm32mp151 <-- stm32mp153 <-- stm32mp157 did)
> stm32h743.dtsi <-- stm32h75x.dtsi (stm32h750, stm32h753, stm32h757
> all with HW crypto/hash inside)
> we can add crypto to stm32h75x.dtsi, i will just rename
> stm32h750.dtsi to stm32h75x.dtsi
>
> I'd like to use option-2, which one do you like?
I think what you did is correct (include stm32h743.dtsi inside
stm32h750.dtsi). It makes sens if you add crypto and ADC nodes inside
stm32h743.dtsi
Cheers
Alex
> thanks.
> regards.
>
>
>
> Dillon,
>>
>>
>>> diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
>>> new file mode 100644
>>> index 000000000000..9bb73bb61901
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
>>> @@ -0,0 +1,229 @@
>>> +/*
>>> + * Copyright 2021 - Dillon Min <dillon.minfei at gmail.com>
>>> + *
>>> + * This file is dual-licensed: you can use it either under the terms
>>> + * of the GPL or the X11 license, at your option. Note that this dual
>>> + * licensing only applies to this file, and not this project as a
>>> + * whole.
>>> + *
>>> + * a) This file is free software; you can redistribute it and/or
>>> + * modify it under the terms of the GNU General Public License as
>>> + * published by the Free Software Foundation; either version 2 of the
>>> + * License, or (at your option) any later version.
>>> + *
>>> + * This file is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>> + * GNU General Public License for more details.
>>> + *
>>> + * Or, alternatively,
>>> + *
>>> + * b) Permission is hereby granted, free of charge, to any person
>>> + * obtaining a copy of this software and associated documentation
>>> + * files (the "Software"), to deal in the Software without
>>> + * restriction, including without limitation the rights to use,
>>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>>> + * sell copies of the Software, and to permit persons to whom the
>>> + * Software is furnished to do so, subject to the following
>>> + * conditions:
>>> + *
>>> + * The above copyright notice and this permission notice shall be
>>> + * included in all copies or substantial portions of the Software.
>>> + *
>>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>>> + * OTHER DEALINGS IN THE SOFTWARE.
>>> + *
>>> + * For art-pi board resources, you can refer to link:
>>> + * https://art-pi.gitee.io/website/
>>> + */
>>> +
>>> +/dts-v1/;
>>> +#include "stm32h750.dtsi"
>>> +#include "stm32h7-pinctrl.dtsi"
>>> +#include <dt-bindings/interrupt-controller/irq.h>
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +
>>> +/ {
>>> + model = "RT-Thread STM32H750i-ART-PI board";
>>> + compatible = "st,stm32h750i-art-pi", "st,stm32h750";
>>> +
>>> + chosen {
>>> + bootargs = "root=/dev/ram";
>>> + stdout-path = "serial0:2000000n8";
>>> + };
>>> +
>>> + memory at c0000000 {
>>> + device_type = "memory";
>>> + reg = <0xc0000000 0x2000000>;
>>> + };
>>> +
>>> + reserved-memory {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + linux,cma {
>>> + compatible = "shared-dma-pool";
>>> + no-map;
>>> + size = <0x100000>;
>>> + linux,dma-default;
>>> + };
>>> + };
>>> +
>>> + aliases {
>>> + serial0 = &uart4;
>>> + serial1 = &usart3;
>>> + };
>>> +
>>> + leds {
>>> + compatible = "gpio-leds";
>>> + led-red {
>>> + gpios = <&gpioi 8 0>;
>>> + };
>>> + led-green {
>>> + gpios = <&gpioc 15 0>;
>>> + linux,default-trigger = "heartbeat";
>>> + };
>>> + };
>>> +
>>> + v3v3: regulator-v3v3 {
>>> + compatible = "regulator-fixed";
>>> + regulator-name = "v3v3";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-always-on;
>>> + };
>>> +
>>> + wlan_pwr: regulator-wlan {
>>> + compatible = "regulator-fixed";
>>> +
>>> + regulator-name = "wl-reg";
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> +
>>> + gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
>>> + enable-active-high;
>>> + };
>>> +};
>>> +
>>> +&clk_hse {
>>> + clock-frequency = <25000000>;
>>> +};
>>> +
>>> +&dma1 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&dma2 {
>>> + status = "okay";
>>> +};
>>> +
>>> +&mac {
>>> + status = "disabled";
>>> + pinctrl-0 = <ðernet_rmii>;
>>> + pinctrl-names = "default";
>>> + phy-mode = "rmii";
>>> + phy-handle = <&phy0>;
>>> +
>>> + mdio0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + compatible = "snps,dwmac-mdio";
>>> + phy0: ethernet-phy at 0 {
>>> + reg = <0>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&sdmmc1 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
>>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>> + broken-cd;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&v3v3>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&sdmmc2 {
>>> + pinctrl-names = "default", "opendrain", "sleep";
>>> + pinctrl-0 = <&sdmmc2_b4_pins_a>;
>>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
>>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
>>> + broken-cd;
>>> + non-removable;
>>> + st,neg-edge;
>>> + bus-width = <4>;
>>> + vmmc-supply = <&wlan_pwr>;
>>> + status = "okay";
>>> +
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + brcmf: bcrmf at 1 {
>>> + reg = <1>;
>>> + compatible = "brcm,bcm4329-fmac";
>>> + };
>>> +};
>>> +
>>> +&spi1 {
>>> + status = "okay";
>>> + pinctrl-0 = <&spi1_pins>;
>>> + pinctrl-names = "default";
>>> + cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
>>> + dmas = <&dmamux1 37 0x400 0x05>,
>>> + <&dmamux1 38 0x400 0x05>;
>>> + dma-names = "rx", "tx";
>>> +
>>> + flash at 0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + compatible = "winbond,w25q128", "jedec,spi-nor";
>>> + reg = <0>;
>>> + spi-max-frequency = <80000000>;
>>> +
>>> + partition at 0 {
>>> + label = "root filesystem";
>>> + reg = <0 0x1000000>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&usart2 {
>>> + pinctrl-0 = <&usart2_pins>;
>>> + pinctrl-names = "default";
>>> + status = "disabled";
>>> +};
>>> +
>>> +&usart3 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&usart3_pins>;
>>> + dmas = <&dmamux1 45 0x400 0x05>,
>>> + <&dmamux1 46 0x400 0x05>;
>>> + dma-names = "rx", "tx";
>>> + st,hw-flow-ctrl;
>>> + status = "okay";
>>> +
>>> + bluetooth {
>>> + compatible = "brcm,bcm43438-bt";
>>> + host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
>>> + device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
>>> + shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
>>> + max-speed = <115200>;
>>> + };
>>> +};
>>> +
>>> +&uart4 {
>>> + pinctrl-0 = <&uart4_pins>;
>>> + pinctrl-names = "default";
>>> + status = "okay";
>>> +};
>>> +
>>> +
>>>
More information about the linux-arm-kernel
mailing list