[PATCH v8 4/6] ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
Alexandre TORGUE
alexandre.torgue at foss.st.com
Tue Mar 30 17:50:37 BST 2021
On 3/30/21 10:58 AM, dillon.minfei at gmail.com wrote:
> From: dillon min <dillon.minfei at gmail.com>
>
> This patchset has following changes:
>
> - introduce stm32h750.dtsi to support stm32h750 value line
> - add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
> - add stm32h750-art-pi.dts to support art-pi board
>
> art-pi board component:
> - 8MiB qspi flash
> - 16MiB spi flash
> - 32MiB sdram
> - ap6212 wifi&bt&fm
>
> the detail board information can be found at:
> https://art-pi.gitee.io/website/
>
> Signed-off-by: dillon min <dillon.minfei at gmail.com>
> ---
> v8:
> - move file stm32h743.dtsi submit position to [PATCH V8 3/6]
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/stm32h750.dtsi | 6 +
> arch/arm/boot/dts/stm32h750i-art-pi.dts | 229 ++++++++++++++++++++++++++++++++
> 3 files changed, 236 insertions(+)
> create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
> create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8e5d4ab4e75e..a19c5ab9df84 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1071,6 +1071,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
> stm32746g-eval.dtb \
> stm32h743i-eval.dtb \
> stm32h743i-disco.dtb \
> + stm32h750i-art-pi.dtb \
> stm32mp153c-dhcom-drc02.dtb \
> stm32mp157a-avenger96.dtb \
> stm32mp157a-dhcor-avenger96.dtb \
> diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
> new file mode 100644
> index 000000000000..41e3b1e3a874
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32h750.dtsi
> @@ -0,0 +1,6 @@
> +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
> +/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
> +
> +#include "stm32h743.dtsi"
> +
I know it's a bit odd, but you could directly include stm32h743.dtsi in
your board as there are no SoC differences.
> diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
> new file mode 100644
> index 000000000000..9bb73bb61901
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
> @@ -0,0 +1,229 @@
> +/*
> + * Copyright 2021 - Dillon Min <dillon.minfei at gmail.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * For art-pi board resources, you can refer to link:
> + * https://art-pi.gitee.io/website/
> + */
> +
> +/dts-v1/;
> +#include "stm32h750.dtsi"
> +#include "stm32h7-pinctrl.dtsi"
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "RT-Thread STM32H750i-ART-PI board";
> + compatible = "st,stm32h750i-art-pi", "st,stm32h750";
> +
> + chosen {
> + bootargs = "root=/dev/ram";
> + stdout-path = "serial0:2000000n8";
> + };
> +
> + memory at c0000000 {
> + device_type = "memory";
> + reg = <0xc0000000 0x2000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + linux,cma {
> + compatible = "shared-dma-pool";
> + no-map;
> + size = <0x100000>;
> + linux,dma-default;
> + };
> + };
> +
> + aliases {
> + serial0 = &uart4;
> + serial1 = &usart3;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + led-red {
> + gpios = <&gpioi 8 0>;
> + };
> + led-green {
> + gpios = <&gpioc 15 0>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + v3v3: regulator-v3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + wlan_pwr: regulator-wlan {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "wl-reg";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&clk_hse {
> + clock-frequency = <25000000>;
> +};
> +
> +&dma1 {
> + status = "okay";
> +};
> +
> +&dma2 {
> + status = "okay";
> +};
> +
> +&mac {
> + status = "disabled";
> + pinctrl-0 = <ðernet_rmii>;
> + pinctrl-names = "default";
> + phy-mode = "rmii";
> + phy-handle = <&phy0>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy at 0 {
> + reg = <0>;
> + };
> + };
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + broken-cd;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
> + broken-cd;
> + non-removable;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&wlan_pwr>;
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + brcmf: bcrmf at 1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-0 = <&spi1_pins>;
> + pinctrl-names = "default";
> + cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
> + dmas = <&dmamux1 37 0x400 0x05>,
> + <&dmamux1 38 0x400 0x05>;
> + dma-names = "rx", "tx";
> +
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "winbond,w25q128", "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <80000000>;
> +
> + partition at 0 {
> + label = "root filesystem";
> + reg = <0 0x1000000>;
> + };
> + };
> +};
> +
> +&usart2 {
> + pinctrl-0 = <&usart2_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> +};
> +
> +&usart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usart3_pins>;
> + dmas = <&dmamux1 45 0x400 0x05>,
> + <&dmamux1 46 0x400 0x05>;
> + dma-names = "rx", "tx";
> + st,hw-flow-ctrl;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
> + device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
> + shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
> + max-speed = <115200>;
> + };
> +};
> +
> +&uart4 {
> + pinctrl-0 = <&uart4_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +
>
More information about the linux-arm-kernel
mailing list