[PATCH v7 3/6] ARM: dts: stm32: introduce stm32h7-pinctrl.dtsi to support stm32h750
Alexandre TORGUE
alexandre.torgue at foss.st.com
Tue Mar 30 08:21:58 BST 2021
Hi Dillon
On 3/30/21 4:28 AM, dillon.minfei at gmail.com wrote:
> From: dillon min <dillon.minfei at gmail.com>
>
> This patch is intend to add support stm32h750 value line,
> just add stm32h7-pinctrl.dtsi for extending, with following changes:
>
> - rename stm32h743-pinctrl.dtsi to stm32h7-pinctrl.dtsi
> - move compatible string "st,stm32h743-pinctrl" from stm32h7-pinctrl.dtsi
> to stm32h743-pinctrl.dtsi
> - move 'pin-controller' from stm32h7-pinctrl.dtsi to stm32h743.dtsi, to
> fix make dtbs_check warrnings
> arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c at 40005C00',
> 'i2c at 58001C00' do not match any of the regexes:
> '@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
>
You are not so far but sorry I still have a remark:
The pin-controller move in stm32h743.dtsi should be done in this patch.
For the moment you don't need to create a dedicate file to only define
the compatible string in stm32h743-pinctrl.dtsi. Just add it in
stm32h743.dtsi. I'm ok to rename stm32h743-pinctrl.dtsi by
stm32h7-pinctrl, and at the end remove stm32h743-pinctrl.dtsi, so don't
forget to change the include file for stm32h743 disco and eval dts file.
Regards
Alex
> Signed-off-by: dillon min <dillon.minfei at gmail.com>
> ---
> v7: no changes
>
> arch/arm/boot/dts/stm32h7-pinctrl.dtsi | 341 +++++++++++++++++++++++++++++++
> arch/arm/boot/dts/stm32h743-pinctrl.dtsi | 307 +---------------------------
> 2 files changed, 347 insertions(+), 301 deletions(-)
> create mode 100644 arch/arm/boot/dts/stm32h7-pinctrl.dtsi
>
> diff --git a/arch/arm/boot/dts/stm32h7-pinctrl.dtsi b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi
> new file mode 100644
> index 000000000000..a5c295eca081
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi
> @@ -0,0 +1,341 @@
> +/*
> + * Copyright 2017 - Alexandre Torgue <alexandre.torgue at st.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/pinctrl/stm32-pinfunc.h>
> +
> +&pinctrl {
> +
> + gpioa: gpio at 58020000 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 0 16>;
> + };
> +
> + gpiob: gpio at 58020400 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 16 16>;
> + };
> +
> + gpioc: gpio at 58020800 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 32 16>;
> + };
> +
> + gpiod: gpio at 58020c00 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 48 16>;
> + };
> +
> + gpioe: gpio at 58021000 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 64 16>;
> + };
> +
> + gpiof: gpio at 58021400 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 80 16>;
> + };
> +
> + gpiog: gpio at 58021800 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 96 16>;
> + };
> +
> + gpioh: gpio at 58021c00 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 112 16>;
> + };
> +
> + gpioi: gpio at 58022000 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 128 16>;
> + };
> +
> + gpioj: gpio at 58022400 {
> + status = "okay";
> + ngpios = <16>;
> + gpio-ranges = <&pinctrl 0 144 16>;
> + };
> +
> + gpiok: gpio at 58022800 {
> + status = "okay";
> + ngpios = <8>;
> + gpio-ranges = <&pinctrl 0 160 8>;
> + };
> +
> + i2c1_pins_a: i2c1-0 {
> + pins {
> + pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
> + <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
> + bias-disable;
> + drive-open-drain;
> + slew-rate = <0>;
> + };
> + };
> +
> + ethernet_rmii: rmii-0 {
> + pins {
> + pinmux = <STM32_PINMUX('G', 11, AF11)>,
> + <STM32_PINMUX('G', 13, AF11)>,
> + <STM32_PINMUX('G', 12, AF11)>,
> + <STM32_PINMUX('C', 4, AF11)>,
> + <STM32_PINMUX('C', 5, AF11)>,
> + <STM32_PINMUX('A', 7, AF11)>,
> + <STM32_PINMUX('C', 1, AF11)>,
> + <STM32_PINMUX('A', 2, AF11)>,
> + <STM32_PINMUX('A', 1, AF11)>;
> + slew-rate = <2>;
> + };
> + };
> +
> + sdmmc1_b4_pins_a: sdmmc1-b4-0 {
> + pins {
> + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
> + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
> + <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
> + slew-rate = <3>;
> + drive-push-pull;
> + bias-disable;
> + };
> + };
> +
> + sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
> + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
> + slew-rate = <3>;
> + drive-push-pull;
> + bias-disable;
> + };
> + pins2{
> + pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
> + slew-rate = <3>;
> + drive-open-drain;
> + bias-disable;
> + };
> + };
> +
> + sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
> + <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
> + <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
> + };
> + };
> +
> + sdmmc2_b4_pins_a: sdmmc2-b4-0 {
> + pins {
> + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */
> + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */
> + <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
> + slew-rate = <3>;
> + drive-push-pull;
> + bias-disable;
> + };
> + };
> +
> + sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
> + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */
> + slew-rate = <3>;
> + drive-push-pull;
> + bias-disable;
> + };
> + pins2{
> + pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
> + slew-rate = <3>;
> + drive-open-drain;
> + bias-disable;
> + };
> + };
> +
> + sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */
> + <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */
> + <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */
> + <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */
> + <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */
> + <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */
> + };
> + };
> +
> + sdmmc1_dir_pins_a: sdmmc1-dir-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
> + <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
> + <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
> + slew-rate = <3>;
> + drive-push-pull;
> + bias-pull-up;
> + };
> + pins2{
> + pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
> + bias-pull-up;
> + };
> + };
> +
> + sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
> + <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
> + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
> + <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
> + };
> + };
> +
> + usart1_pins: usart1-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
> + bias-disable;
> + };
> + };
> +
> + usart2_pins: usart2-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
> + bias-disable;
> + };
> + };
> +
> + usart3_pins: usart3-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
> + <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
> + <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
> + bias-disable;
> + };
> + };
> +
> + uart4_pins: uart4-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */
> + bias-disable;
> + };
> + };
> +
> + usbotg_hs_pins_a: usbotg-hs-0 {
> + pins {
> + pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */
> + <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
> + <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */
> + <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */
> + <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */
> + <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */
> + <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */
> + <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
> + <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
> + <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
> + <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
> + <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <2>;
> + };
> + };
> +
> + spi1_pins: spi1-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('A', 5, AF5)>,
> + /* SPI1_CLK */
> + <STM32_PINMUX('B', 5, AF5)>;
> + /* SPI1_MOSI */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <2>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('G', 9, AF5)>;
> + /* SPI1_MISO */
> + bias-disable;
> + };
> + };
> +};
> +
> diff --git a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
> index fa5dcb6a5fdd..6b1e115307b9 100644
> --- a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
> @@ -1,306 +1,11 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> /*
> - * Copyright 2017 - Alexandre Torgue <alexandre.torgue at st.com>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - * a) This file is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of the
> - * License, or (at your option) any later version.
> - *
> - * This file is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - * b) Permission is hereby granted, free of charge, to any person
> - * obtaining a copy of this software and associated documentation
> - * files (the "Software"), to deal in the Software without
> - * restriction, including without limitation the rights to use,
> - * copy, modify, merge, publish, distribute, sublicense, and/or
> - * sell copies of the Software, and to permit persons to whom the
> - * Software is furnished to do so, subject to the following
> - * conditions:
> - *
> - * The above copyright notice and this permission notice shall be
> - * included in all copies or substantial portions of the Software.
> - *
> - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - * OTHER DEALINGS IN THE SOFTWARE.
> + * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
> + * Author: Alexandre Torgue <alexandre.torgue at st.com> for STMicroelectronics.
> */
>
> -#include <dt-bindings/pinctrl/stm32-pinfunc.h>
> +#include "stm32h7-pinctrl.dtsi"
>
> -/ {
> - soc {
> - pin-controller {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "st,stm32h743-pinctrl";
> - ranges = <0 0x58020000 0x3000>;
> - interrupt-parent = <&exti>;
> - st,syscfg = <&syscfg 0x8>;
> - pins-are-numbered;
> -
> - gpioa: gpio at 58020000 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x0 0x400>;
> - clocks = <&rcc GPIOA_CK>;
> - st,bank-name = "GPIOA";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpiob: gpio at 58020400 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x400 0x400>;
> - clocks = <&rcc GPIOB_CK>;
> - st,bank-name = "GPIOB";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpioc: gpio at 58020800 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x800 0x400>;
> - clocks = <&rcc GPIOC_CK>;
> - st,bank-name = "GPIOC";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpiod: gpio at 58020c00 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0xc00 0x400>;
> - clocks = <&rcc GPIOD_CK>;
> - st,bank-name = "GPIOD";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpioe: gpio at 58021000 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x1000 0x400>;
> - clocks = <&rcc GPIOE_CK>;
> - st,bank-name = "GPIOE";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpiof: gpio at 58021400 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x1400 0x400>;
> - clocks = <&rcc GPIOF_CK>;
> - st,bank-name = "GPIOF";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpiog: gpio at 58021800 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x1800 0x400>;
> - clocks = <&rcc GPIOG_CK>;
> - st,bank-name = "GPIOG";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpioh: gpio at 58021c00 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x1c00 0x400>;
> - clocks = <&rcc GPIOH_CK>;
> - st,bank-name = "GPIOH";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpioi: gpio at 58022000 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x2000 0x400>;
> - clocks = <&rcc GPIOI_CK>;
> - st,bank-name = "GPIOI";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpioj: gpio at 58022400 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x2400 0x400>;
> - clocks = <&rcc GPIOJ_CK>;
> - st,bank-name = "GPIOJ";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - gpiok: gpio at 58022800 {
> - gpio-controller;
> - #gpio-cells = <2>;
> - reg = <0x2800 0x400>;
> - clocks = <&rcc GPIOK_CK>;
> - st,bank-name = "GPIOK";
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - };
> -
> - i2c1_pins_a: i2c1-0 {
> - pins {
> - pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
> - <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
> - bias-disable;
> - drive-open-drain;
> - slew-rate = <0>;
> - };
> - };
> -
> - ethernet_rmii: rmii-0 {
> - pins {
> - pinmux = <STM32_PINMUX('G', 11, AF11)>,
> - <STM32_PINMUX('G', 13, AF11)>,
> - <STM32_PINMUX('G', 12, AF11)>,
> - <STM32_PINMUX('C', 4, AF11)>,
> - <STM32_PINMUX('C', 5, AF11)>,
> - <STM32_PINMUX('A', 7, AF11)>,
> - <STM32_PINMUX('C', 1, AF11)>,
> - <STM32_PINMUX('A', 2, AF11)>,
> - <STM32_PINMUX('A', 1, AF11)>;
> - slew-rate = <2>;
> - };
> - };
> -
> - sdmmc1_b4_pins_a: sdmmc1-b4-0 {
> - pins {
> - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
> - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
> - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
> - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
> - <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
> - <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
> - slew-rate = <3>;
> - drive-push-pull;
> - bias-disable;
> - };
> - };
> -
> - sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
> - pins1 {
> - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
> - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
> - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
> - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
> - <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
> - slew-rate = <3>;
> - drive-push-pull;
> - bias-disable;
> - };
> - pins2{
> - pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
> - slew-rate = <3>;
> - drive-open-drain;
> - bias-disable;
> - };
> - };
> -
> - sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
> - pins {
> - pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
> - <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
> - <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
> - <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
> - <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
> - <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
> - };
> - };
> -
> - sdmmc1_dir_pins_a: sdmmc1-dir-0 {
> - pins1 {
> - pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
> - <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
> - <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
> - slew-rate = <3>;
> - drive-push-pull;
> - bias-pull-up;
> - };
> - pins2{
> - pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
> - bias-pull-up;
> - };
> - };
> -
> - sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
> - pins {
> - pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
> - <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
> - <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
> - <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
> - };
> - };
> -
> - usart1_pins: usart1-0 {
> - pins1 {
> - pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
> - bias-disable;
> - drive-push-pull;
> - slew-rate = <0>;
> - };
> - pins2 {
> - pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
> - bias-disable;
> - };
> - };
> -
> - usart2_pins: usart2-0 {
> - pins1 {
> - pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
> - bias-disable;
> - drive-push-pull;
> - slew-rate = <0>;
> - };
> - pins2 {
> - pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
> - bias-disable;
> - };
> - };
> -
> - usbotg_hs_pins_a: usbotg-hs-0 {
> - pins {
> - pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */
> - <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
> - <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */
> - <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */
> - <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */
> - <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */
> - <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */
> - <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
> - <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
> - <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
> - <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
> - <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */
> - bias-disable;
> - drive-push-pull;
> - slew-rate = <2>;
> - };
> - };
> - };
> - };
> +&pinctrl{
> + compatible = "st,stm32h743-pinctrl";
> };
>
More information about the linux-arm-kernel
mailing list