[PATCH v2 10/13] dt-bindings: spi: cadence-qspi: Add support for Pensando Elba SoC
Brad Larson
brad at pensando.io
Mon Mar 29 02:59:35 BST 2021
Add new vendor Pensando Systems Elba SoC compatible
string and convert to json-schema.
Signed-off-by: Brad Larson <brad at pensando.io>
---
.../bindings/spi/cadence-quadspi.txt | 68 --------
.../bindings/spi/cadence-quadspi.yaml | 153 ++++++++++++++++++
2 files changed, 153 insertions(+), 68 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 8ace832a2d80..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,68 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
- Generic default - "cdns,qspi-nor".
- For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
- For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
- For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
- physical address and length. The first entry is the address and
- length of the controller register set. The second entry is the
- address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
- the read data rather than the QSPI clock. Make sure that QSPI return
- clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
- mode chip select outputs are de-asserted between
- transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
- de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
- transaction and deasserting the device chip select
- (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
- and first bit transfer.
-- resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names : Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
- qspi: spi at ff705000 {
- compatible = "cdns,qspi-nor";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0xff705000 0x1000>,
- <0xffa00000 0x1000>;
- interrupts = <0 151 4>;
- clocks = <&qspi_clk>;
- cdns,is-decoded-cs;
- cdns,fifo-depth = <128>;
- cdns,fifo-width = <4>;
- cdns,trigger-address = <0x00000000>;
- resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
- reset-names = "qspi", "qspi-ocp";
-
- flash0: n25q00 at 0 {
- ...
- cdns,read-delay = <4>;
- cdns,tshsl-ns = <50>;
- cdns,tsd2d-ns = <50>;
- cdns,tchsh-ns = <4>;
- cdns,tslch-ns = <4>;
- };
- };
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
new file mode 100644
index 000000000000..94d631045153
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
@@ -0,0 +1,153 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+ - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar at linux.intel.com>
+ - Brad Larson <brad at pensando.io>
+
+properties:
+ compatible:
+ contains:
+ enum:
+ - cdns,qspi-nor # Generic default
+ - ti,k2g-qspi # TI 66AK2G SoC
+ - ti,am654-ospi # TI AM654 SoC
+ - intel,lgm-qspi # Intel LGM SoC
+ - pensando,cdns-qspi # Pensando Elba SoC
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ reg:
+ minItems: 2
+ maxItems: 2
+ description: |
+ Contains two entries, each of which is a tuple consisting of a
+ physical address and length. The first entry is the address and
+ length of the controller register set. The second entry is the
+ address and length of the QSPI Controller data area.
+
+ interrupts:
+ maxItems: 1
+ description: Unit interrupt specifier for the controller interrupt
+
+ clocks:
+ description: phandle to the Quad SPI clock
+
+ cdns,fifo-depth:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Size of the data FIFO in words
+
+ cdns,fifo-width:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Bus width of the data FIFO in bytes
+
+ cdns,trigger-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: 32-bit indirect AHB trigger address
+
+ cdns,is-decoded-cs:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Flag to indicate whether decoder is used or not
+
+ cdns,rclk-en:
+ description:
+ Flag to indicate that QSPI return clock is used to latch the
+ read data rather than the QSPI clock. Make sure that QSPI return
+ clock is populated on the board before using this property
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ # Subnodes of the Cadence Quad SPI controller are spi slave nodes
+ # with additional custom properties
+ cdns,read-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Delay for read capture logic, in clock cycles
+
+ cdns,tshsl-ns:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay in nanoseconds for the length that the master mode chip
+ select outputs are de-asserted between transactions
+
+ cdns,tsd2d-ns:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay in nanoseconds between one chip select being de-activated
+ and the activation of another.
+
+ cdns,tchsh-ns:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay in nanoseconds between last bit of current transaction and
+ deasserting the device chip select (qspi_n_ss_out).
+
+ cdns,tslch-ns:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay in nanoseconds between setting qspi_n_ss_out low and first
+ bit transfer.
+
+ resets:
+ items:
+ - description: qspi reset
+ - description: qspi-ocp reset
+
+ reset-names:
+ items:
+ - const: qspi
+ - const: qspi-ocp
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - cdns,fifo-depth
+ - cdns,fifo-width
+ - cdns,trigger-address
+
+patternProperties:
+ "^.*@[0-9]+$":
+ type: object
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/reset/altr,rst-mgr-a10.h>
+ qspi: spi at ff705000 {
+ compatible = "cdns,qspi-nor";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ clocks = <&qspi_clk>;
+ cdns,is-decoded-cs;
+ cdns,fifo-depth = <128>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x00000000>;
+ resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
+ reset-names = "qspi", "qspi-ocp";
+
+ flash0: mt25q at 0 {
+ compatible = "jdec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ spi-rx-bus-width = <2>;
+ m25p,fast-read;
+ cdns,read-delay = <0>;
+ cdns,tshsl-ns = <0>;
+ cdns,tsd2d-ns = <0>;
+ cdns,tchsh-ns = <0>;
+ cdns,tslch-ns = <0>;
+ };
+ };
--
2.17.1
More information about the linux-arm-kernel
mailing list