[PATCH 0/3] Apple M1 DART IOMMU driver

[Mark Kettenis]

> From: Arnd Bergmann <arnd at kernel.org>
> Date: Fri, 26 Mar 2021 20:59:58 +0100
> 
> On Fri, Mar 26, 2021 at 6:51 PM Sven Peter <sven at svenpeter.dev> wrote:
> > On Fri, Mar 26, 2021, at 18:34, Robin Murphy wrote:
> > > On 2021-03-26 17:26, Mark Kettenis wrote:
> > > >
> > > > Anyway, from my viewpoint having the information about the IOVA
> > > > address space sit on the devices makes little sense.  This information
> > > > is needed by the DART driver, and there is no direct cnnection from
> > > > the DART to the individual devices in the devicetree.  The "iommus"
> > > > property makes a connection in the opposite direction.
> > >
> > > What still seems unclear is whether these addressing limitations are a
> > > property of the DART input interface, the device output interface, or
> > > the interconnect between them. Although the observable end result
> > > appears more or less the same either way, they are conceptually
> > > different things which we have different abstractions to deal with.
> >
> > I'm not really sure if there is any way for us to figure out where these
> > limitation comes from though.
> 
> My first guess was that this is done to partition the available address
> address space in a way that allows one physical IOTLB to handle
> multiple devices that each have their own page table for a subset
> of the address space, as was done on old PowerPC IOMMUs.
> However, the ranges you list don't really support that model.
> 
> > I've done some more experiments and looked at all DART nodes in Apple's Device
> > Tree though. It seems that most (if not all) masters only connect 32 address
> > lines even though the iommu can handle a much larger address space. I'll therefore
> > remove the code to handle the full space for v2 since it's essentially dead
> > code that can't be tested anyway.
> >
> >
> > There are some exceptions though:
> >
> > There are the PCIe DARTs which have a different limitation which could be
> > encoded as 'dma-ranges' in the pci bus node:
> >
> >            name         base      size
> >          dart-apcie1: 00100000  3fe00000
> >          dart-apcie2: 00100000  3fe00000
> >          dart-apcie0: 00100000  3fe00000
> >         dart-apciec0: 00004000  7fffc000
> >         dart-apciec1: 80000000  7fffc000
> 
> This looks like they are reserving some address space in the beginning
> and/or the end, and for apciec0, the address space is partitioned into
> two equal-sized regions.
> 
> > Then there are also these display controller DARTs. If we wanted to use dma-ranges
> > we could just put them in a single sub bus:
> >
> >               name     base      size
> >           dart-disp0: 00000000 fc000000
> >             dart-dcp: 00000000 fc000000
> >        dart-dispext0: 00000000 fc000000
> >          dart-dcpext: 00000000 fc000000
> >
> >
> > And finally we have these strange ones which might eventually each require
> > another awkward sub-bus if we want to stick to the dma-ranges property.
> >
> >     name     base      size
> >   dart-aop: 00030000 ffffffff ("always-on processor")
> >   dart-pmp: 00000000 bff00000 (no idea yet)
> 
> Here I also see a "pio-vm-size" property:
> 
>     dart-pmp {
>       pio-vm-base = <0xc0000000>;
>       pio-vm-size = <0x40000000>;
>       vm-size = <0xbff00000>;
>       ...
>    };
> 
> Which seems to give 3GB of address space to the normal iotlb,
> plus the last 1GB to something else. The vm-base property is also
> missing rather than zero, but that could just be part of their syntax
> instead of a real difference.

Yes.  It seems like "vm-base" is omitted when it is 0, and "vm-size"
is omitted when the end of the window is at 0xffffffff.

> 
> Could it be that there are
> 
> >   dart-sio: 0021c000 fbde4000 (at least their Secure Enclave/TPM co-processor)
> 
> Same here:
>     dart-sio {
>        vm-base = <0x0>;
>        vm-size = <0xfc000000>;
>        pio-vm-base = <0xfd000000>;
>       pio-vm-size = <0x2000000>;
>       pio-granularity = <0x1000000>;
>    }
> 
> There are clearly two distinct ranges that split up the 4GB space again,
> with a small hole of 16MB (==pio-granularity) at the end of each range.
> 
> The "pio" name might indicate that this is a range of addresses that
> can be programmed to point at I/O registers in another device, rather
> than pointing to RAM.
> 
>            Arnd
>