[PATCH 2/2] arm64: dts: marvell: clearfog-gt-8k: add cooling maps

[Russell King]

Add cooling maps suitable for a Noctua NF-A4/10 fan attached to the
heat sink.  The fan will toggle between two speeds in operation which
seems to be normal behaviour.  More fine-grained steps may help to
reduce this.

Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
---
 .../marvell/armada-8040-clearfog-gt-8k.dts    | 122 +++++++++++++++++-
 1 file changed, 121 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index b1723ac0aeec..0ec0d5625818 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -31,8 +31,11 @@
 		ethernet2 = &cp1_eth2;
 	};
 
-	pwm {
+	fan: pwm {
 		compatible = "pwm-fan";
+		/* 20% steps */
+		cooling-levels = <0 51 102 153 204 255>;
+		#cooling-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp0_fan_pwm_pins>;
 		pwms = <&cp0_gpio2 16 40000>;
@@ -109,6 +112,123 @@
 	};
 };
 
+&ap_thermal_ic {
+	polling-delay = <1000>; /* milliseconds */
+	trips {
+		ap_active: trip-active {
+			temperature = <40000>; /* millicelsius */
+			hysteresis = <4000>; /* millicelsius */
+			type = "active";
+		};
+	};
+	cooling-maps {
+		map0 {
+			trip = <&ap_active>;
+			cooling-device = <&fan THERMAL_NO_LIMIT 4>;
+		};
+		map1 {
+			trip = <&ap_crit>;
+			cooling-device = <&fan 4 5>;
+		};
+	};
+};
+
+&cp0_thermal_ic {
+	polling-delay = <1000>; /* milliseconds */
+	trips {
+		cp0_active0: trip-active0 {
+			temperature = <40000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp0_active1: trip-active1 {
+			temperature = <45000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp0_active2: trip-active2 {
+			temperature = <50000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp0_active3: trip-active3 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+	};
+	cooling-maps {
+		map0 {
+			trip = <&cp0_active0>;
+			cooling-device = <&fan 0 1>;
+		};
+		map1 {
+			trip = <&cp0_active1>;
+			cooling-device = <&fan 1 2>;
+		};
+		map2 {
+			trip = <&cp0_active2>;
+			cooling-device = <&fan 2 3>;
+		};
+		map3 {
+			trip = <&cp0_active3>;
+			cooling-device = <&fan 3 4>;
+		};
+		map4 {
+			trip = <&cp0_crit>;
+			cooling-device = <&fan 4 5>;
+		};
+	};
+};
+
+&cp1_thermal_ic {
+	polling-delay = <1000>; /* milliseconds */
+	trips {
+		cp1_active0: trip-active0 {
+			temperature = <40000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp1_active1: trip-active1 {
+			temperature = <45000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp1_active2: trip-active2 {
+			temperature = <50000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+		cp1_active3: trip-active3 {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2500>; /* millicelsius */
+			type = "active";
+		};
+	};
+	cooling-maps {
+		map0 {
+			trip = <&cp1_active0>;
+			cooling-device = <&fan 0 1>;
+		};
+		map1 {
+			trip = <&cp1_active1>;
+			cooling-device = <&fan 1 2>;
+		};
+		map2 {
+			trip = <&cp1_active2>;
+			cooling-device = <&fan 2 3>;
+		};
+		map3 {
+			trip = <&cp1_active3>;
+			cooling-device = <&fan 3 4>;
+		};
+		map4 {
+			trip = <&cp1_crit>;
+			cooling-device = <&fan 4 5>;
+		};
+	};
+};
+
 &uart0 {
 	status = "okay";
 	pinctrl-0 = <&uart0_pins>;
-- 
2.20.1