[RESEND PATCH v5 4/4] dt-bindings: devfreq: rk3399_dmc: Remove references of unexistant defines
Chanwoo Choi
cw00.choi at samsung.com
Tue Mar 9 10:16:34 GMT 2021
On 3/9/21 8:38 AM, Daniel Lezcano wrote:
> From: Gaël PORTAY <gael.portay at collabora.com>
>
> Those DDR related defines do not exist. Replace their references with
> their numerical constant.
>
> Signed-off-by: Gaël PORTAY <gael.portay at collabora.com>
> Reviewed-by: Rob Herring <robh at kernel.org>
> Signed-off-by: Daniel Lezcano <daniel.lezcano at linaro.org>
> ---
> .../bindings/devfreq/rk3399_dmc.txt | 73 +++++++++----------
> 1 file changed, 34 insertions(+), 39 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
> index a41bcfef95c8..ddde2c4f97df 100644
> --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
> +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
> @@ -79,24 +79,23 @@ Following properties relate to DDR timing:
>
> - rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines
> the DRAM side driver strength in ohms. Default
> - value is DDR3_DS_40ohm.
> + value is 40.
>
> - rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines
> the DRAM side ODT strength in ohms. Default value
> - is DDR3_ODT_120ohm.
> + is 120.
>
> - rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines
> the phy side CA line (incluing command line,
> address line and clock line) driver strength.
> - Default value is PHY_DRV_ODT_40.
> + Default value is 40.
>
> - rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines
> the PHY side DQ line (including DQS/DQ/DM line)
> - driver strength. Default value is PHY_DRV_ODT_40.
> + driver strength. Default value is 40.
>
> - rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines
> - the PHY side ODT strength. Default value is
> - PHY_DRV_ODT_240.
> + the PHY side ODT strength. Default value is 240.
>
> - rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines
> then ODT disable frequency in MHz (Mega Hz).
> @@ -106,25 +105,23 @@ Following properties relate to DDR timing:
>
> - rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines
> the DRAM side driver strength in ohms. Default
> - value is LP3_DS_34ohm.
> + value is 34.
>
> - rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines
> the DRAM side ODT strength in ohms. Default value
> - is LP3_ODT_240ohm.
> + is 240.
>
> - rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines
> the PHY side CA line (including command line,
> address line and clock line) driver strength.
> - Default value is PHY_DRV_ODT_40.
> + Default value is 40.
>
> - rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines
> the PHY side DQ line (including DQS/DQ/DM line)
> - driver strength. Default value is
> - PHY_DRV_ODT_40.
> + driver strength. Default value is 40.
>
> - rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define
> - the phy side odt strength, default value is
> - PHY_DRV_ODT_240.
> + the phy side odt strength, default value is 240.
>
> - rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter
> defines the ODT disable frequency in
> @@ -134,32 +131,30 @@ Following properties relate to DDR timing:
>
> - rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines
> the DRAM side driver strength in ohms. Default
> - value is LP4_PDDS_60ohm.
> + value is 60.
>
> - rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines
> the DRAM side ODT on DQS/DQ line strength in ohms.
> - Default value is LP4_DQ_ODT_40ohm.
> + Default value is 40.
>
> - rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines
> the DRAM side ODT on CA line strength in ohms.
> - Default value is LP4_CA_ODT_40ohm.
> + Default value is 40.
>
> - rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines
> the PHY side CA line (including command address
> - line) driver strength. Default value is
> - PHY_DRV_ODT_40.
> + line) driver strength. Default value is 40.
>
> - rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines
> the PHY side clock line and CS line driver
> - strength. Default value is PHY_DRV_ODT_80.
> + strength. Default value is 80.
>
> - rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines
> the PHY side DQ line (including DQS/DQ/DM line)
> - driver strength. Default value is PHY_DRV_ODT_80.
> + driver strength. Default value is 80.
>
> - rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines
> - the PHY side ODT strength. Default value is
> - PHY_DRV_ODT_60.
> + the PHY side ODT strength. Default value is 60.
>
> Example:
> dmc_opp_table: dmc_opp_table {
> @@ -195,23 +190,23 @@ Example:
> rockchip,phy_dll_dis_freq = <125>;
> rockchip,auto_pd_dis_freq = <666>;
> rockchip,ddr3_odt_dis_freq = <333>;
> - rockchip,ddr3_drv = <DDR3_DS_40ohm>;
> - rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
> - rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
> - rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
> - rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
> + rockchip,ddr3_drv = <40>;
> + rockchip,ddr3_odt = <120>;
> + rockchip,phy_ddr3_ca_drv = <40>;
> + rockchip,phy_ddr3_dq_drv = <40>;
> + rockchip,phy_ddr3_odt = <240>;
> rockchip,lpddr3_odt_dis_freq = <333>;
> - rockchip,lpddr3_drv = <LP3_DS_34ohm>;
> - rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
> - rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
> - rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
> - rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
> + rockchip,lpddr3_drv = <34>;
> + rockchip,lpddr3_odt = <240>;
> + rockchip,phy_lpddr3_ca_drv = <40>;
> + rockchip,phy_lpddr3_dq_drv = <40>;
> + rockchip,phy_lpddr3_odt = <240>;
> rockchip,lpddr4_odt_dis_freq = <333>;
> - rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
> - rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
> - rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
> - rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
> - rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
> - rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
> - rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;
> + rockchip,lpddr4_drv = <60>;
> + rockchip,lpddr4_dq_odt = <40>;
> + rockchip,lpddr4_ca_odt = <40>;
> + rockchip,phy_lpddr4_ca_drv = <40>;
> + rockchip,phy_lpddr4_ck_cs_drv = <80>;
> + rockchip,phy_lpddr4_dq_drv = <80>;
> + rockchip,phy_lpddr4_odt = <60>;
> };
>
Applied it with following minor fixup (unneeded spaces). Thanks
diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
index ddde2c4f97df..ac189dd82b08 100644
--- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
+++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
@@ -154,7 +154,7 @@ Following properties relate to DDR timing:
driver strength. Default value is 80.
- rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines
- the PHY side ODT strength. Default value is 60.
+ the PHY side ODT strength. Default value is 60.
--
Best Regards,
Chanwoo Choi
Samsung Electronics
More information about the linux-arm-kernel
mailing list