[PATCH 2/2] net: stmmac: Add Ingenic SoCs MAC support.

[Zhou Yanjie]

Hi Andrew,

On 2021/6/8 上午8:01, Andrew Lunn wrote:
>>   config DWMAC_ROCKCHIP
>>   	tristate "Rockchip dwmac support"
>> -	default ARCH_ROCKCHIP
>> +	default MACH_ROCKCHIP
>>   	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
>>   	select MFD_SYSCON
>>   	help
>> @@ -164,7 +176,7 @@ config DWMAC_STI
>>   
>>   config DWMAC_STM32
>>   	tristate "STM32 DWMAC support"
>> -	default ARCH_STM32
>> +	default MACH_STM32
> It would be good to explain in the commit message why you are changing
> these two. It is not obvious.


Apologize for my carelessness, this is left over accidentally when 
cleaning up the code, I will remove them in the next version.


>
>> +static int jz4775_mac_set_mode(struct plat_stmmacenet_data *plat_dat)
>> +{
>> +	struct ingenic_mac *mac = plat_dat->bsp_priv;
>> +	int val;
>> +
>> +	switch (plat_dat->interface) {
>> +	case PHY_INTERFACE_MODE_MII:
>> +		val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
>> +			  FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_MII);
>> +		pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_MII\n");
>> +		break;
>> +
>> +	case PHY_INTERFACE_MODE_GMII:
>> +		val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
>> +			  FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_GMII);
>> +		pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_GMII\n");
>> +		break;
>> +
>> +	case PHY_INTERFACE_MODE_RMII:
>> +		val = FIELD_PREP(MACPHYC_TXCLK_SEL_MASK, MACPHYC_TXCLK_SEL_INPUT) |
>> +			  FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_RMII);
>> +		pr_debug("MAC PHY Control Register: PHY_INTERFACE_MODE_RMII\n");
>> +		break;
>> +
>> +	case PHY_INTERFACE_MODE_RGMII:
> What about the other three RGMII modes?
>
>> +	case PHY_INTERFACE_MODE_RGMII:
>> +		val = FIELD_PREP(MACPHYC_TX_SEL_MASK, MACPHYC_TX_SEL_DELAY) |
>> +			  FIELD_PREP(MACPHYC_TX_DELAY_MASK, MACPHYC_TX_DELAY_63_UNIT) |
>> +			  FIELD_PREP(MACPHYC_RX_SEL_MASK, MACPHYC_RX_SEL_ORIGIN) |
>> +			  FIELD_PREP(MACPHYC_PHY_INFT_MASK, MACPHYC_PHY_INFT_RGMII);
> What exactly does MACPHYC_TX_DELAY_63_UNIT mean here? Ideally, the MAC
> should not be adding any RGMII delays. It should however pass mode
> through to the PHY, so it can add the delays, if the mode indicates it
> should, e.g. PHY_INTERFACE_MODE_RGMII_ID. This is also why you should
> be handling all 4 RGMII modes here, not just one.


MACPHYC_TX_DELAY_63_UNIT means set MAC TX clk delay to 63 units (similar to the "tx-delay" in dwmac-rk.c). However, the manual does not clearly describe the time span of one unit, after consulting engineer of Ingenic, I learned that the value is recommended to be set to 63.
I will change it to be similar to the way done in dwmac-rk.c.

Thanks and best regards!


>
> 	 Andrew