[RESEND PATCH net-next v5 2/3] net: pcs: add 2500BASEX support for Intel mGbE controller
Vladimir Oltean
vladimir.oltean at nxp.com
Fri Jun 4 05:00:18 PDT 2021
On Fri, Jun 04, 2021 at 06:57:32PM +0800, Michael Sit Wei Hong wrote:
> From: Voon Weifeng <weifeng.voon at intel.com>
>
> XPCS IP supports 2500BASEX as PHY interface. It is configured as
> autonegotiation disable to cater for PHYs that does not supports 2500BASEX
> autonegotiation.
>
> v2: Add supported link speed masking.
> v3: Restructure to introduce xpcs_config_2500basex() used to configure the
> xpcs for 2.5G speeds. Added 2500BASEX specific information for
> configuration.
> v4: Fix indentation error
>
> Signed-off-by: Voon Weifeng <weifeng.voon at intel.com>
> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit at intel.com>
> ---
> drivers/net/pcs/pcs-xpcs.c | 56 ++++++++++++++++++++++++++++++++++++
> include/linux/pcs/pcs-xpcs.h | 1 +
> 2 files changed, 57 insertions(+)
>
> diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
> index 34164437c135..98c4a3973402 100644
> --- a/drivers/net/pcs/pcs-xpcs.c
> +++ b/drivers/net/pcs/pcs-xpcs.c
> @@ -57,9 +57,12 @@
>
> /* Clause 37 Defines */
> /* VR MII MMD registers offsets */
> +#define DW_VR_MII_MMD_CTRL 0x0000
> #define DW_VR_MII_DIG_CTRL1 0x8000
> #define DW_VR_MII_AN_CTRL 0x8001
> #define DW_VR_MII_AN_INTR_STS 0x8002
> +/* Enable 2.5G Mode */
> +#define DW_VR_MII_DIG_CTRL1_2G5_EN BIT(2)
> /* EEE Mode Control Register */
> #define DW_VR_MII_EEE_MCTRL0 0x8006
> #define DW_VR_MII_EEE_MCTRL1 0x800b
> @@ -86,6 +89,11 @@
> #define DW_VR_MII_C37_ANSGM_SP_1000 0x2
> #define DW_VR_MII_C37_ANSGM_SP_LNKSTS BIT(4)
>
> +/* SR MII MMD Control defines */
> +#define AN_CL37_EN BIT(12) /* Enable Clause 37 auto-nego */
> +#define SGMII_SPEED_SS13 BIT(13) /* SGMII speed along with SS6 */
> +#define SGMII_SPEED_SS6 BIT(6) /* SGMII speed along with SS13 */
> +
> /* VR MII EEE Control 0 defines */
> #define DW_VR_MII_EEE_LTX_EN BIT(0) /* LPI Tx Enable */
> #define DW_VR_MII_EEE_LRX_EN BIT(1) /* LPI Rx Enable */
> @@ -161,6 +169,14 @@ static const int xpcs_sgmii_features[] = {
> __ETHTOOL_LINK_MODE_MASK_NBITS,
> };
>
> +static const int xpcs_2500basex_features[] = {
> + ETHTOOL_LINK_MODE_Asym_Pause_BIT,
> + ETHTOOL_LINK_MODE_Autoneg_BIT,
> + ETHTOOL_LINK_MODE_2500baseX_Full_BIT,
> + ETHTOOL_LINK_MODE_2500baseT_Full_BIT,
> + __ETHTOOL_LINK_MODE_MASK_NBITS,
> +};
> +
This is a general design comment, perhaps you could address this later,
but do keep it in mind:
I don't think the PCS has anything to do with whether the link will
support flow control.
Similarly, Aquantia (now Marvell) PHYs operating in 2500base-x mode are
capable of negotiating the copper-side link to 10/100/1000/2500 even if
the system-side link is fixed at 2500. The way this is achieved is by
the PHY emitting PAUSE frames towards the MAC in order to achieve rate
adaptation with the external link speed.
This is not completely standardized in phylink at the moment, but we
have systems where this works. My point is that maybe the PCS driver
isn't the most appropriate place to implement the phylink_validate
method - the MAC driver is almost always in the position to know better.
If you could move the xpcs validation inside stmmac I think that would
be an improvement. For example with the NXP SJA1105 patches that I am
going to send out for review soon, I am not calling xpcs_validate() at
all.
> static const phy_interface_t xpcs_usxgmii_interfaces[] = {
> PHY_INTERFACE_MODE_USXGMII,
> };
> @@ -177,11 +193,17 @@ static const phy_interface_t xpcs_sgmii_interfaces[] = {
> PHY_INTERFACE_MODE_SGMII,
> };
>
> +static const phy_interface_t xpcs_2500basex_interfaces[] = {
> + PHY_INTERFACE_MODE_2500BASEX,
> + PHY_INTERFACE_MODE_MAX,
> +};
> +
> enum {
> DW_XPCS_USXGMII,
> DW_XPCS_10GKR,
> DW_XPCS_XLGMII,
> DW_XPCS_SGMII,
> + DW_XPCS_2500BASEX,
> DW_XPCS_INTERFACE_MAX,
> };
>
> @@ -306,6 +328,7 @@ static int xpcs_soft_reset(struct mdio_xpcs_args *xpcs,
> dev = MDIO_MMD_PCS;
> break;
> case DW_AN_C37_SGMII:
> + case DW_2500BASEX:
> dev = MDIO_MMD_VEND2;
> break;
> default:
> @@ -804,6 +827,28 @@ static int xpcs_config_aneg_c37_sgmii(struct mdio_xpcs_args *xpcs)
> return xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_DIG_CTRL1, ret);
> }
>
> +static int xpcs_config_2500basex(struct mdio_xpcs_args *xpcs)
> +{
> + int ret;
> +
> + ret = xpcs_read(xpcs, MDIO_MMD_VEND2, DW_VR_MII_DIG_CTRL1);
> + if (ret < 0)
> + return ret;
> + ret |= DW_VR_MII_DIG_CTRL1_2G5_EN;
> + ret &= ~DW_VR_MII_DIG_CTRL1_MAC_AUTO_SW;
> + ret = xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_DIG_CTRL1, ret);
> + if (ret < 0)
> + return ret;
> +
> + ret = xpcs_read(xpcs, MDIO_MMD_VEND2, DW_VR_MII_MMD_CTRL);
> + if (ret < 0)
> + return ret;
> + ret &= ~AN_CL37_EN;
> + ret |= SGMII_SPEED_SS6;
> + ret &= ~SGMII_SPEED_SS13;
> + return xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_MMD_CTRL, ret);
> +}
> +
> static int xpcs_do_config(struct mdio_xpcs_args *xpcs,
> phy_interface_t interface, unsigned int mode)
> {
> @@ -827,6 +872,11 @@ static int xpcs_do_config(struct mdio_xpcs_args *xpcs,
> if (ret)
> return ret;
> break;
> + case DW_2500BASEX:
> + ret = xpcs_config_2500basex(xpcs);
> + if (ret)
> + return ret;
> + break;
> default:
> return -1;
> }
> @@ -1023,6 +1073,12 @@ static const struct xpcs_compat synopsys_xpcs_compat[DW_XPCS_INTERFACE_MAX] = {
> .num_interfaces = ARRAY_SIZE(xpcs_sgmii_interfaces),
> .an_mode = DW_AN_C37_SGMII,
> },
> + [DW_XPCS_2500BASEX] = {
> + .supported = xpcs_2500basex_features,
> + .interface = xpcs_2500basex_interfaces,
> + .num_interfaces = ARRAY_SIZE(xpcs_2500basex_features),
> + .an_mode = DW_2500BASEX,
> + },
> };
>
> static const struct xpcs_id xpcs_id_list[] = {
> diff --git a/include/linux/pcs/pcs-xpcs.h b/include/linux/pcs/pcs-xpcs.h
> index 0860a5b59f10..4d815f03b4b2 100644
> --- a/include/linux/pcs/pcs-xpcs.h
> +++ b/include/linux/pcs/pcs-xpcs.h
> @@ -13,6 +13,7 @@
> /* AN mode */
> #define DW_AN_C73 1
> #define DW_AN_C37_SGMII 2
> +#define DW_2500BASEX 3
>
> struct xpcs_id;
>
> --
> 2.17.1
>
More information about the linux-arm-kernel
mailing list