[PATCH v1 net-next 3/3] net: stmmac: ptp: update tas basetime after ptp adjust

[Xiaoliang Yang]

After adjusting the ptp time, the Qbv base time may be the past time
of the new current time. dwmac5 hardware limited the base time cannot
be set as past time. This patch calculate the base time and reset the
Qbv configuration after ptp time adjust.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1 at nxp.com>
---
 .../net/ethernet/stmicro/stmmac/stmmac_ptp.c  | 41 ++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
index 4e86cdf2bc9f..c573bc8b2595 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
@@ -62,7 +62,8 @@ static int stmmac_adjust_time(struct ptp_clock_info *ptp, s64 delta)
 	u32 sec, nsec;
 	u32 quotient, reminder;
 	int neg_adj = 0;
-	bool xmac;
+	bool xmac, est_rst = false;
+	int ret;
 
 	xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
 
@@ -75,10 +76,48 @@ static int stmmac_adjust_time(struct ptp_clock_info *ptp, s64 delta)
 	sec = quotient;
 	nsec = reminder;
 
+	/* If EST is enabled, disabled it before adjust ptp time. */
+	if (priv->plat->est && priv->plat->est->enable) {
+		est_rst = true;
+		mutex_lock(&priv->plat->est->lock);
+		priv->plat->est->enable = false;
+		stmmac_est_configure(priv, priv->ioaddr, priv->plat->est,
+				     priv->plat->clk_ptp_rate);
+		mutex_unlock(&priv->plat->est->lock);
+	}
+
 	spin_lock_irqsave(&priv->ptp_lock, flags);
 	stmmac_adjust_systime(priv, priv->ptpaddr, sec, nsec, neg_adj, xmac);
 	spin_unlock_irqrestore(&priv->ptp_lock, flags);
 
+	/* Caculate new basetime and re-configured EST after PTP time adjust. */
+	if (est_rst) {
+		struct timespec64 current_time, time;
+		ktime_t current_time_ns, basetime;
+		u64 cycle_time;
+
+		priv->ptp_clock_ops.gettime64(&priv->ptp_clock_ops, &current_time);
+		current_time_ns = timespec64_to_ktime(current_time);
+		time.tv_nsec = priv->plat->est->btr[0];
+		time.tv_sec = priv->plat->est->btr[1];
+		basetime = timespec64_to_ktime(time);
+		cycle_time = priv->plat->est->ctr[1] * NSEC_PER_SEC +
+			     priv->plat->est->ctr[0];
+		time = stmmac_calc_tas_basetime(basetime,
+						current_time_ns,
+						cycle_time);
+
+		mutex_lock(&priv->plat->est->lock);
+		priv->plat->est->btr[0] = (u32)time.tv_nsec;
+		priv->plat->est->btr[1] = (u32)time.tv_sec;
+		priv->plat->est->enable = true;
+		ret = stmmac_est_configure(priv, priv->ioaddr, priv->plat->est,
+					   priv->plat->clk_ptp_rate);
+		mutex_unlock(&priv->plat->est->lock);
+		if (ret)
+			netdev_err(priv->dev, "failed to configure EST\n");
+	}
+
 	return 0;
 }
 
-- 
2.17.1