[PATCH] ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM

[Alexandre TORGUE]

Hi Marek

On 7/21/21 8:10 PM, Marek Vasut wrote:
> While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
> fixed the LED0 assignment on the PDK2 board, the same commit did not
> update the touchscreen IRQ line assignment, which is the same GPIO line,
> shared between the LED0 output and touchscreen IRQ input. To make this
> more convoluted, the same EXTI input (not the same GPIO line) is shared
> between Button B which is Active-Low IRQ, and touchscreen IRQ which is
> Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
> board with touchscreen is in use, which is the case here, LED0 must be
> disabled, Button B must be polled, so the touchscreen interrupt works as
> it should.
> 
> Update the touchscreen IRQ line assignment, disable LED0 and use polled
> GPIO button driver for Button B, since the DT here describes baseboard
> with LCD board.
> 

Applied on stm32-fixes

regards
alex

> Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
> Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Alexandre Torgue <alexandre.torgue at foss.st.com>
> Cc: Patrice Chotard <patrice.chotard at foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay at foss.st.com>
> Cc: linux-stm32 at st-md-mailman.stormreply.com
> To: linux-arm-kernel at lists.infradead.org
> ---
>   arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 24 +++++++++++--------
>   1 file changed, 14 insertions(+), 10 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
> index 4f6b94f10f4a9..fbf3826933e4d 100644
> --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
> +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
> @@ -38,7 +38,7 @@ gpio-keys-polled {
>   		poll-interval = <20>;
>   
>   		/*
> -		 * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
> +		 * The EXTi IRQ line 3 is shared with ethernet,
>   		 * so mark this as polled GPIO key.
>   		 */
>   		button-0 {
> @@ -47,6 +47,16 @@ button-0 {
>   			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
>   		};
>   
> +		/*
> +		 * The EXTi IRQ line 6 is shared with touchscreen,
> +		 * so mark this as polled GPIO key.
> +		 */
> +		button-1 {
> +			label = "TA2-GPIO-B";
> +			linux,code = <KEY_B>;
> +			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
> +		};
> +
>   		/*
>   		 * The EXTi IRQ line 0 is shared with PMIC,
>   		 * so mark this as polled GPIO key.
> @@ -61,13 +71,6 @@ button-2 {
>   	gpio-keys {
>   		compatible = "gpio-keys";
>   
> -		button-1 {
> -			label = "TA2-GPIO-B";
> -			linux,code = <KEY_B>;
> -			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
> -			wakeup-source;
> -		};
> -
>   		button-3 {
>   			label = "TA4-GPIO-D";
>   			linux,code = <KEY_D>;
> @@ -83,6 +86,7 @@ led-0 {
>   			label = "green:led5";
>   			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
>   			default-state = "off";
> +			status = "disabled";
>   		};
>   
>   		led-1 {
> @@ -202,8 +206,8 @@ sgtl5000_rx_endpoint: endpoint at 1 {
>   	touchscreen at 38 {
>   		compatible = "edt,edt-ft5406";
>   		reg = <0x38>;
> -		interrupt-parent = <&gpiog>;
> -		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
> +		interrupt-parent = <&gpioc>;
> +		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
>   	};
>   };
>   
>