[PATCH] ARM: dts: Add device trees for Coyote and IXDPG425
Linus Walleij
linus.walleij at linaro.org
Wed Jul 28 08:10:59 PDT 2021
This adds device trees for the ADI Engineering Coyote and the
Intel IXDPG425 reference design. The ethernet set-up on the
IXDPG425 is a bit dubious because I think it uses a DSA
switch chip, but this is a good as it gets right now.
The Coyote boardfile claims an IDE port exist at 0xFFFE1000
but the implementation does not use this. If you have the
board and can/want to test, please contact me.
Cc: Deepak Saxena <dsaxena at plexity.net>
Cc: Vladimir Barinov <vladimir.barinov at cogentembedded.com>
Cc: Zoltan HERPAI <wigyori at uid0.hu>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
Zoltan: looping you on this patch since you have the Pronghorn
which I think is the sequel to the Coyote.
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts | 110 +++++++++++++++
arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts | 125 ++++++++++++++++++
3 files changed, 237 insertions(+)
create mode 100644 arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts
create mode 100644 arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f1f189e3a938..ac8a4a77584d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -245,6 +245,8 @@ dtb-$(CONFIG_ARCH_IXP4XX) += \
intel-ixp42x-ixdp425.dtb \
intel-ixp43x-kixrp435.dtb \
intel-ixp46x-ixdp465.dtb \
+ intel-ixp42x-adi-coyote.dtb \
+ intel-ixp42x-ixdpg425.dtb \
intel-ixp42x-iomega-nas100d.dtb \
intel-ixp42x-dlink-dsm-g600.dtb \
intel-ixp42x-gateworks-gw2348.dtb \
diff --git a/arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts b/arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts
new file mode 100644
index 000000000000..44c017b78008
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for ADI Engineering Coyote platform.
+ * Derived from boardfiles written by MontaVista software.
+ * Ethernet set-up from OpenWrt.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ADI Engineering Coyote reference design";
+ compatible = "adieng,coyote", "intel,ixp42x";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory at 0 {
+ /* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */
+ device_type = "memory";
+ reg = <0x00000000 0x01000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+ stdout-path = "uart1:115200n8";
+ };
+
+ aliases {
+ /* These are switched around */
+ serial0 = &uart1;
+ serial1 = &uart0;
+ };
+
+ soc {
+ bus at c4000000 {
+ flash at 0,0 {
+ compatible = "intel,ixp4xx-flash", "cfi-flash";
+ bank-width = <2>;
+ /*
+ * 32 MB of Flash in 128 0x20000 sized blocks
+ * mapped in at CS0 and CS1
+ */
+ reg = <0 0x00000000 0x2000000>;
+
+ /* Configure expansion bus to allow writes */
+ intel,ixp4xx-eb-write-enable = <1>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* CHECKME: guess this is Redboot FIS */
+ fis-index-block = <0x1ff>;
+ };
+ };
+ };
+
+ pci at c0000000 {
+ status = "ok";
+
+ /*
+ * Taken from Coyote PCI boardfile.
+ * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+ * each handling all IRQs.
+ */
+ interrupt-map =
+ /* IDSEL 1 */
+ <0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */
+ <0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */
+ <0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */
+ <0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */
+ /* IDSEL 2 */
+ <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */
+ <0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */
+ <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */
+ <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */
+ };
+
+ /* EthB */
+ ethernet at c8009000 {
+ status = "ok";
+ queue-rx = <&qmgr 3>;
+ queue-txready = <&qmgr 20>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy5>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ };
+
+ phy5: ethernet-phy at 5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ /* EthC */
+ ethernet at c800a000 {
+ status = "ok";
+ queue-rx = <&qmgr 4>;
+ queue-txready = <&qmgr 21>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts b/arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts
new file mode 100644
index 000000000000..002a8705abc9
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel IXDPG425 reference design.
+ * Derived from boardfiles written by MontaVista software.
+ * Ethernet set-up from OpenWrt.
+ *
+ * The device has 4 x FXS RJ11 ports for analog phones for
+ * internet telephony. (Not supported yet.)
+ *
+ * The device has 9 status LEDs we do not support yet.
+ *
+ * This device is very similar to ADI engingeering Coyote.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Intel IXDPG425 reference design";
+ compatible = "intel,ixdpg425", "intel,ixp42x";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory at 0 {
+ /* 32 MB SDRAM */
+ device_type = "memory";
+ reg = <0x00000000 0x02000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+ stdout-path = "uart0:115200n8";
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ soc {
+ bus at c4000000 {
+ flash at 0,0 {
+ compatible = "intel,ixp4xx-flash", "cfi-flash";
+ bank-width = <2>;
+ /*
+ * CHECKME: the product brief says 16MB in a flash
+ * socket.
+ */
+ reg = <0 0x00000000 0x1000000>;
+
+ /* Configure expansion bus to allow writes */
+ intel,ixp4xx-eb-write-enable = <1>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* CHECKME: guess this is Redboot FIS */
+ fis-index-block = <0x7f>;
+ };
+ };
+ };
+
+ pci at c0000000 {
+ status = "ok";
+
+ /*
+ * Taken from IXDPG425 PCI boardfile.
+ * We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ
+ * for 12 & 13 and one for 14.
+ */
+ interrupt-map =
+ /* IDSEL 12 */
+ <0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */
+ <0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */
+ <0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */
+ <0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */
+ /* IDSEL 13 */
+ <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
+ <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
+ <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
+ <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
+ /* IDSEL 14 */
+ <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
+ <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
+ <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
+ <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
+ };
+
+ /*
+ * CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind
+ * of Realtek DSA switch on the board.
+ */
+
+ /* EthB */
+ ethernet at c8009000 {
+ status = "ok";
+ queue-rx = <&qmgr 3>;
+ queue-txready = <&qmgr 20>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy5>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ };
+
+ phy5: ethernet-phy at 5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ /* EthC */
+ ethernet at c800a000 {
+ status = "ok";
+ queue-rx = <&qmgr 4>;
+ queue-txready = <&qmgr 21>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ };
+ };
+};
--
2.31.1
More information about the linux-arm-kernel
mailing list