[PATCH 1/2] ARM: dts: at91: add pinctrl-{names, 0} for all gpios
Claudiu Beznea
claudiu.beznea at microchip.com
Tue Jul 27 00:40:05 PDT 2021
Add pinctrl-names and pinctrl-0 properties on controllers that claims to
use pins to avoid failures due to
commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges")
and also to avoid using pins that may be claimed my other IPs.
Fixes: b7c2b6157079 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained
board")
Signed-off-by: Claudiu Beznea <claudiu.beznea at microchip.com>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 16 +++++++++++-
arch/arm/boot/dts/at91-sama5d3_xplained.dts | 29 +++++++++++++++++++++
arch/arm/boot/dts/at91-sama5d4_xplained.dts | 19 ++++++++++++++
3 files changed, 63 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index edca66c232c1..ebbc9b23aef1 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -92,6 +92,8 @@ sw1 {
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
status = "okay"; /* Conflict with pwm0. */
red {
@@ -537,6 +539,10 @@ AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_H
AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA19 DAT2 periph A with pullup */
AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA20 DAT3 periph A with pullup */
};
+ pinctrl_sdmmc0_cd: sdmmc0_cd {
+ atmel,pins =
+ <AT91_PIOA 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
};
sdmmc1 {
@@ -569,6 +575,14 @@ pinctrl_usb_default: usb_default {
AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
};
};
+
+ leds {
+ pinctrl_gpio_leds: gpio_leds {
+ atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOB 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
}; /* pinctrl */
&pwm0 {
@@ -580,7 +594,7 @@ &pwm0 {
&sdmmc0 {
bus-width = <4>;
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
status = "okay";
cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
disable-wp;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index 9c55a921263b..cc55d1684322 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -57,6 +57,8 @@ slot at 0 {
};
spi0: spi at f0004000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_cs>;
cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
status = "okay";
};
@@ -169,6 +171,8 @@ slot at 0 {
};
spi1: spi at f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_cs>;
cs-gpios = <&pioC 25 0>;
status = "okay";
};
@@ -248,6 +252,26 @@ pinctrl_usb_default: usb_default {
<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
};
+
+ pinctrl_gpio_leds: gpio_leds_default {
+ atmel,pins =
+ <AT91_PIOE 23 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_spi0_cs: spi0_cs_default {
+ atmel,pins =
+ <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_spi1_cs: spi1_cs_default {
+ atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_vcc_mmc0_reg_gpio: vcc_mmc0_reg_gpio_default {
+ atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
};
};
};
@@ -339,6 +363,8 @@ rootfs at 800000 {
vcc_mmc0_reg: fixedregulator_mmc0 {
compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
regulator-name = "mmc0-card-supply";
regulator-min-microvolt = <3300000>;
@@ -362,6 +388,9 @@ bp3 {
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+ status = "okay";
d2 {
label = "d2";
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index 046796c5b9b0..541779af049f 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -80,6 +80,8 @@ usart4: serial at fc010000 {
};
spi1: spi at fc018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_cs>;
cs-gpios = <&pioB 21 0>;
status = "okay";
};
@@ -137,6 +139,19 @@ pinctrl_macb0_phy_irq: macb0_phy_irq_0 {
atmel,pins =
<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
+ pinctrl_spi0_cs: spi0_cs_default {
+ atmel,pins =
+ <AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_gpio_leds: gpio_leds_default {
+ atmel,pins =
+ <AT91_PIOD 30 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOE 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_vcc_mmc1_reg: vcc_mmc1_reg {
+ atmel,pins =
+ <AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
};
};
};
@@ -242,6 +257,8 @@ pb_user1 {
leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
status = "okay";
d8 {
@@ -268,6 +285,8 @@ vcc_3v3_reg: fixedregulator_3v3 {
vcc_mmc1_reg: fixedregulator_mmc1 {
compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_vcc_mmc1_reg>;
gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
regulator-name = "VDD MCI1";
regulator-min-microvolt = <3300000>;
--
2.25.1
More information about the linux-arm-kernel
mailing list