[PATCH v8 11/11] arm64: dts: allwinner: h616: Add X96 Mate TV box support

Andre Przywara andre.przywara at arm.com
Fri Jul 23 08:38:38 PDT 2021


The X96 Mate is an Allwinner H616 based TV box, featuring:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 2GiB/4GiB RAM (fully usable!)
  - 16/32/64GiB eMMC
  - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
  - Unsupported Allwinner WiFi chip
  - 2 x USB 2.0 host ports
  - HDMI port
  - IR receiver
  - 5V/2A DC power supply via barrel plug

For more information see: https://linux-sunxi.org/X96_Mate

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h616-x96-mate.dts    | 178 ++++++++++++++++++
 2 files changed, 179 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 62f8d43cf84d..14053c566601 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 000000000000..6334f4e20fd0
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "X96 Mate";
+	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdce>;
+	vqmmc-supply = <&reg_bldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic at 745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+				status = "disabled";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo3: aldo3 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+				status = "disabled";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8-2";
+				status = "disabled";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc2v5";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.17.6




More information about the linux-arm-kernel mailing list