[RFC 1/2] dt-bindings: PCI: imx6: add fsl,imx6q-pcie.yaml
Richard Zhu
hongxing.zhu at nxp.com
Thu Jul 22 01:22:34 PDT 2021
Convert the fsl,imx6q-pcie.txt into a schema.
Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
---
.../bindings/pci/fsl,imx6q-pcie.yaml | 212 ++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 213 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
new file mode 100644
index 000000000000..b66b681d7ad7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -0,0 +1,212 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6 PCIe host controller
+
+maintainers:
+ - Lucas Stach <l.stach at pengutronix.de>
+ - Richard Zhu <hongxing.zhu at nxp.com>
+
+description: |+
+ This PCIe host controller is based on the Synopsys DesignWare PCIe IP
+ and thus inherits all the common properties defined in snps,dw-pcie.yaml.
+
+allOf:
+ - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+ compatible:
+ const: fsl,imx6q-pcie
+ const: fsl,imx6sx-pcie
+ const: fsl,imx6qp-pcie
+ const: fsl,imx7d-pcie
+ const: fsl,imx8mq-pcie
+
+ reg:
+ items:
+ - description: Data Bus Interface (DBI) registers.
+ - description: PCIe configuration space region.
+
+ reg-names:
+ items:
+ - const: dbi
+ - const: config
+
+ interrupts:
+ minItems: 1
+ items:
+ - description: builtin MSI controller.
+
+ interrupt-names:
+ minItems: 1
+ items:
+ - const: msi
+
+ clocks:
+ minItems: 3
+ maxItems: 4
+ items:
+ - description: PCIe bridge clock.
+ - description: PCIe bus clock.
+ - description: PCIe PHY clock.
+ - description: Additional required clock entry for imx6sx-pcie,
+ imx8mq-pcie.
+
+ clock-names:
+ minItems: 3
+ maxItems: 4
+ items:
+ - const: pcie
+ - const: pcie_bus
+ - const: pcie_phy
+ - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
+
+ num-lanes:
+ const: 1
+
+ num-viewport:
+ const: 4
+
+ fsl,imx7d-pcie-phy:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: A phandle to an fsl,imx7d-pcie-phy node. Additional
+ required properties for imx7d-pcie and imx8mq-pcie.
+
+ power-domains:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ minItems: 1
+ maxItems: 2
+ items:
+ - description: Phandle pointing to the DISPLAY domain for imx6sx-pcie,
+ to PCIE_PHY power domain for imx7d-pcie and imx8mq-pcie.
+ - description: Phandle pointing to the PCIE_PHY power domains for
+ imx6sx-pcie.
+
+ power-domain-names:
+ minItems: 1
+ maxItems: 2
+ items:
+ - const: pcie
+ - const: pcie_phy
+
+ resets:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ items:
+ - description: Phandles to PCIe-related reset lines exposed by SRC
+ IP block. Additional required by imx7d-pcie and imx8mq-pcie.
+
+ reset-names:
+ items:
+ - const: pciephy
+ - const: apps
+ - const: turnoff
+
+ fsl,tx-deemph-gen1:
+ description: Gen1 De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ fsl,tx-deemph-gen2-3p5db:
+ description: Gen2 (3.5db) De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ fsl,tx-deemph-gen2-6db:
+ description: Gen2 (6db) De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 20
+
+ fsl,tx-swing-full:
+ description: Gen2 TX SWING FULL value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 127
+
+ fsl,tx-swing-low:
+ description: TX launch amplitude swing_low value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 127
+
+ fsl,max-link-speed:
+ description: Specify PCI Gen for link capability (optional required).
+ Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
+ requirements and thus for gen2 capability a gen2 compliant clock
+ generator should be used and configured.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 3, 4]
+ default: 1
+
+ reset-gpio:
+ description: Should specify the GPIO for controlling the PCI bus device
+ reset signal. It's not polarity aware and defaults to active-low reset
+ sequence (L=reset state, H=operation state) (optional required).
+
+ reset-gpio-active-high:
+ description: If present then the reset sequence using the GPIO
+ specified in the "reset-gpio" property is reversed (H=reset state,
+ L=operation state) (optional required).
+
+ vpcie-supply:
+ description: Should specify the regulator in charge of PCIe port power.
+ The regulator will be enabled when initializing the PCIe host and
+ disabled either as part of the init process or when shutting down
+ the host (optional required).
+
+ vph-supply:
+ description: Should specify the regulator in charge of VPH one of
+ the three PCIe PHY powers. This regulator can be supplied by both
+ 1.8v and 3.3v voltage supplies (optional required).
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - "#address-cells"
+ - "#size-cells"
+ - device_type
+ - bus-range
+ - ranges
+ - num-lanes
+ - num-viewport
+ - interrupts
+ - interrupt-names
+ - "#interrupt-cells"
+ - interrupt-map-mask
+ - interrupt-map
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ pcie: pcie at 1ffc000 {
+ compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+ reg = <0x01ffc000 0x04000>,
+ <0x01f00000 0x80000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0x00 0xff>;
+ ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
+ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
+ num-lanes = <1>;
+ num-viewport = <4>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
+ <&clks IMX6QDL_CLK_LVDS1_GATE>,
+ <&clks IMX6QDL_CLK_PCIE_REF_125M>;
+ clock-names = "pcie", "pcie_bus", "pcie_phy";
+ status = "disabled";
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 2c5dc7d20d81..a616e250d846 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14186,6 +14186,7 @@ L: linux-pci at vger.kernel.org
L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
F: drivers/pci/controller/dwc/*imx6*
PCI DRIVER FOR FU740
--
2.17.1
More information about the linux-arm-kernel
mailing list