[PATCH] ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM

[Marek Vasut]

While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.

Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.

Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Alexandre Torgue <alexandre.torgue at foss.st.com>
Cc: Patrice Chotard <patrice.chotard at foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay at foss.st.com>
Cc: linux-stm32 at st-md-mailman.stormreply.com
To: linux-arm-kernel at lists.infradead.org
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 24 +++++++++++--------
 1 file changed, 14 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 4f6b94f10f4a9..fbf3826933e4d 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -38,7 +38,7 @@ gpio-keys-polled {
 		poll-interval = <20>;
 
 		/*
-		 * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
+		 * The EXTi IRQ line 3 is shared with ethernet,
 		 * so mark this as polled GPIO key.
 		 */
 		button-0 {
@@ -47,6 +47,16 @@ button-0 {
 			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
 		};
 
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
 		/*
 		 * The EXTi IRQ line 0 is shared with PMIC,
 		 * so mark this as polled GPIO key.
@@ -61,13 +71,6 @@ button-2 {
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		button-1 {
-			label = "TA2-GPIO-B";
-			linux,code = <KEY_B>;
-			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
-
 		button-3 {
 			label = "TA4-GPIO-D";
 			linux,code = <KEY_D>;
@@ -83,6 +86,7 @@ led-0 {
 			label = "green:led5";
 			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
+			status = "disabled";
 		};
 
 		led-1 {
@@ -202,8 +206,8 @@ sgtl5000_rx_endpoint: endpoint at 1 {
 	touchscreen at 38 {
 		compatible = "edt,edt-ft5406";
 		reg = <0x38>;
-		interrupt-parent = <&gpiog>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
 	};
 };
 
-- 
2.30.2