[PATCH 2/4] ARM: dts: imx6qp-prtwd3: Fix the SPI chipselect polarity

[Fabio Estevam]

The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
    
[    4.854337] m25p80 at 0 enforce active low on chipselect handle
   
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
    
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
    
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
    
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.

The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
    
[    4.854337] m25p80 at 0 enforce active low on chipselect handle
   
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
    
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
    
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
    
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.

Signed-off-by: Fabio Estevam <festevam at gmail.com>
---
 arch/arm/boot/dts/imx6qp-prtwd3.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qp-prtwd3.dts b/arch/arm/boot/dts/imx6qp-prtwd3.dts
index c42723989bc0..1a334918f9ca 100644
--- a/arch/arm/boot/dts/imx6qp-prtwd3.dts
+++ b/arch/arm/boot/dts/imx6qp-prtwd3.dts
@@ -123,7 +123,7 @@ &can1 {
 };
 
 &ecspi2 {
-	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
@@ -189,7 +189,7 @@ fixed-link {
 };
 
 &ecspi3 {
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
-- 
2.25.1