[PATCH v1 3/5] arm64: dts: mt8195: add gce node

[Jason-JH Lin]

On Thu, 2021-07-01 at 07:21 +0800, Chun-Kuang Hu wrote:
> Hi, Jason:
> 
> jason-jh.lin <jason-jh.lin at mediatek.com> 於 2021年6月30日 週三 下午1:18寫道：
> > 
> > add gce node on dts file.
> > 
> > Change-Id: I805455cb7c645cb5a24ce1c87fe891a807069123
> > Signed-off-by: jason-jh.lin <jason-jh.lin at mediatek.com>
> > ---
> > This patch is based on [1]
> > [1] Add Mediatek SoC MT8195 and evaluation board dts and Makefile
> >     - 
> > https://patchwork.kernel.org/project/linux-mediatek/patch/20210601075350.31515-2-seiya.wang@mediatek.com/
> > ---
> >  arch/arm64/boot/dts/mediatek/mt8195.dtsi | 21
> > +++++++++++++++++++++
> >  1 file changed, 21 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > index c146a91c6272..38054196eea4 100644
> > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > @@ -6,6 +6,7 @@
> > 
> >  /dts-v1/;
> >  #include <dt-bindings/clock/mt8195-clk.h>
> > +#include <dt-bindings/gce/mt8195-gce.h>
> >  #include <dt-bindings/interrupt-controller/arm-gic.h>
> >  #include <dt-bindings/interrupt-controller/irq.h>
> >  #include <dt-bindings/power/mt8195-power.h>
> > @@ -717,6 +718,26 @@
> >                         #clock-cells = <1>;
> >                 };
> > 
> > +               gce0: mdp_mailbox at 10320000 {
> > +                       compatible = "mediatek,mt8195-gce";
> > +                       reg = <0 0x10320000 0 0x4000>;
> > +                       interrupts = <GIC_SPI 226
> > IRQ_TYPE_LEVEL_HIGH 0>;
> > +                       #mbox-cells = <3>;
> > +                       clocks = <&infracfg_ao CLK_INFRA_AO_GCE>,
> > +                                <&infracfg_ao CLK_INFRA_AO_GCE2>;
> > +                       clock-names = "gce", "gce1";
> > +               };
> > +
> > +               gce1: disp_mailbox at 10330000 {
> > +                       compatible = "mediatek,mt8195-gce";
> > +                       reg = <0 0x10330000 0 0x4000>;
> > +                       interrupts = <GIC_SPI 228
> > IRQ_TYPE_LEVEL_HIGH 0>;
> > +                       #mbox-cells = <3>;
> > +                       clocks = <&infracfg_ao CLK_INFRA_AO_GCE>,
> > +                                <&infracfg_ao CLK_INFRA_AO_GCE2>;
> > +                       clock-names = "gce", "gce1";
> 
> I think each gce could be broken into two function block, the core
> function block and event processing block.
> Each block has independent clock source and "gce" is for core
> function
> block and "gce1" is for event processing block, is it?
> If so, the core function of gce0 and gce1 has common clock source
> (<&infracfg_ao CLK_INFRA_AO_GCE>), right?
> 
> Regards,
> Chun-Kuang.
> 
> > +               };
> > +
> >                 uart0: serial at 11001100 {
> >                         compatible = "mediatek,mt8195-uart",
> > "mediatek,mt6577-uart";
> >                         reg = <0 0x11001100 0 0x100>;
> > --
> > 2.18.0
> > 
gce0 and gce1 are two duplicate hardware node each of them have thier
own core function block and event proccessing block.
The clocks: <&infracfg_ao CLK_INFRA_AO_GCE> is for gce0,
<&infracfg_ao CLK_INFRA_AO_GCE2> is for gce1.

For the design of GCE hardware event signal transportation, each cmdq
mailbox should enable or disable the other gce clk at the same time.

I put two clock source in one gce node so that I can get both of them
easier when each cmdq driver probe.
But I think take out the other gce clk for each gce node is fine.
I will modify it at the next patch version.

Regards,
Jason-JH.Lin.
-- 
Jason-JH Lin <jason-jh.lin at mediatek.com>